- 您现在的位置：买卖IC网 > Datasheet目录610 > 90017-3 (TE Connectivity)ASSY SAHT Datasheet资料下载
参数资料
| 型号： | 90017-3 |
| 厂商： | TE Connectivity |
| 文件页数： | 3/4页 |
| 文件大小： | 0K |
| 描述： | ASSY SAHT |
| 标准包装： | 5 |
| 系列： | Certi-Crimp, Amp-Leaf |
| 工具类型： | 手动压接器 |
| 适用于相关产品： | 卡边缘触点，18-22 AWG |
| 特点： | 侧面插入，棘齿 |
| 配用： | 42840-3-ND - CONT AMP LEAF L/P 30/3 AU 583989-4-ND - CONN CONTACT 22-18AWG 15AU CRIMP 583989-3-ND - CONT AMP LEAF L/P 30/3 AU |
408-7622
month, the inspection frequency should be based on
the amount of use, ambient working conditions,
operator training and skill, and established company
standards. These inspections should be performed in
the following sequence:
A. Visual Inspection
1. Remove all lubrication and accumulated film by
immersing the tool (handles partially closed) into a
suitable degreaser that will not affect paint or plastic
material.
Position Point on
Center of Wire Barrel
Opposite Seam
Modified
Anvil
“A”
±0.038
[±.0015]
2. Make certain all retaining pins are in place and
are secured with the proper retaining rings. If
replacements are necessary, refer to Figure 5.
3. Close the tool handles until the ratchet releases,
and then allow the handles to open freely. If they do
not open quickly and fully, then the spring is
defective and must be replaced (see Section 5,
REPLACEMENT AND REPAIR).
4. Inspect the tool, with special emphasis on
CONTACT
NUMBER
(LP)
42840
583989
60082
583272
583994
WIRE SIZE
AWG (Max)
20
(2) 22
18
CRIMP SECT
(Wire Size
Marking)
22-20
2-22
1-18
CRIMP
HEIGHT
DIM. “A”
0.978 [.0385]
1.130 [.0445]
checking for worn, cracked, or broken crimping
dies. If damage to any part of the head is evident,
return the tool for evaluation and repair (see Section
5, REPLACEMENT AND REPAIR).
B. Crimp Height Inspection
Crimp height inspection is performed through the
use of a micrometer with a modified anvil,
commonly referred to as a crimp height comparator. ?
TE does not market crimp height comparators.
Refer to Instruction Sheet 408-7424 for detailed
information on obtaining and using a crimp height
comparator.
Proceed as follows:
1. Refer to the chart in Figure 4 and select a contact
and a wire (maximum size) for each crimp section.
2. Refer to Section 3, CRIMPING PROCEDURE,
and crimp the contact(s) accordingly.
3. Using a crimp height comparator, measure the
wire barrel crimp height as shown in Figure 4. If the
crimp height conforms to that shown in the chart,
the tool is considered dimensionally correct. If not,
return the tool for evaluation and repair (refer to
Section 5, REPLACEMENT AND REPAIR).
C. Ratchet Inspection
Obtain a 0.025-mm [.001-in.] shim that is suitable for
checking the clearance between the bottoming
surfaces of the crimping dies. Proceed as follows:
1. Select a contact and maximum size wire for the
hand tool.
2. Position the contact and wire between the
crimping dies, as described in Section 3,
CRIMPING PROCEDURE.
Rev B
Figure 4
3. Holding the wire in place, squeeze the tool
handles together until the CERTI-CRIMP ratchet
releases. Hold the handles in this position,
maintaining just enough tension to keep the dies
closed.
4. Check the clearance between the bottoming
surfaces of the crimping dies. If the clearance is
0.025 [.001] or less, the ratchet is satisfactory. If the
clearance exceeds 0.025 [.001], the ratchet is out of
adjustment and must be repaired.
If the tool conforms to these inspection procedures,
lubricate it with a thin coat of any good SAE 20 motor
oil and return it to service.
5. REPLACEMENT AND REPAIR
The parts listed in Figure 5 are customer- replaceable.
A complete inventory can be stocked and controlled to
prevent lost time when replacement of parts is
necessary. Order replacement parts through your ?
TE Connectivity, or call 1-800-526-5142, or send a
facsimile of your purchase order to 1-717-986-7605, or
write to:
CUSTOMER SERVICE (038-035) ?
TYCO ELECTRONICS CORPORATION ?
PO BOX 3608 ?
HARRISBURG PA 17105-3608
For customer repair service, call 1-800-526-5136.
3 of 4
相关PDF资料 |
PDF描述 |
|---|---|
| 90026 | TOOL SHORT HANDLE 24-22AWG CRIMP |
| 90045 | DAHT F CRIMP 14-18 |
| 90050-1 | DAHT TAPER PIN 16-20 |
| 90062 | DAHT F CRIMP 14-24 |
| 90075-1 | ASSY SAHT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 9001730000 | 制造商:Weidmuller 功能描述:BLADE, AQM 3/4 -EA - Bulk |
| 90017305 | 制造商: 功能描述: 制造商:undefined 功能描述: |
| 90-0174 | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:PACKAGE LAND PATTERN, (U5) 5L SOT23 |
| 900-174 | 制造商:Eclipse Tools 功能描述: |
| 90-0175 | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:PACKAGE LAND PATTERN, (U6) 6L SOT |
发布紧急采购，3分钟左右您将得到回复。