- 您现在的位置：买卖IC网 > PDF目录18489 > 90240-2 (TE Connectivity)DIE PIDG 69875 14-12 PDF资料下载
参数资料
| 型号： | 90240-2 |
| 厂商： | TE Connectivity |
| 文件页数： | 1/4页 |
| 文件大小： | 0K |
| 描述： | DIE PIDG 69875 14-12 |
| 标准包装： | 1 |
| 系列： | * |
| 配用： | A0905CT-ND - CONN RECEPT FAST 12-14 AWG .250 A0905TR-ND - CONN RECEPT FAST 12-14 AWG .250 |
Crimping Die Assemblies
90240- 2, 90248- 2, and 90280- 1
Instruction Sheet
408-- 7563
14 MAR 11 Rev B
Die
Holding
Screw
Assembly
Screw
Moving
Die
Floating
Crimper
Wire Strip
Length
(See Table)
PIDG* FASTON*
Terminal
Wire
Barrel
Saddle
AMP--TAPETRONIC*
Machine 69875
Die
Holding
Screw
Insulation
Conductor
Insulation
Barrel
Stationary
Die
NOTE: Not to Scale
SERIES
DIE
ASSEMBLY
NUMBER
PART NUMBER
(TAPE MOUNTED)
TERMINAL
INSULATION
COLOR
RANGE
(AWG)
WIRE
STRIP LENGTH
+0.41 [.016]
INSULATION
DIA (Max)
90248--2
90240--2
90280--1
60894--2
61048--2
61060--2
42844--3
61198--4
.110
.250
Clear
Green
Yellow
22 -- 18
14 -- 12
12 -- 10
5.56 [.219]
8.74 [.344]
7.14 [.281]
2.54 [.100]
6.35 [.250]
Figure 1
All dimensions on this sheet are in millimeters
[with inch equivalents provided in brackets].
1. INTRODUCTION
This instruction sheet covers die assemblies that are
used to crimp PIDG FASTON Terminals. Refer to
Figure 1 for appropriate die assembly and terminal
combinations. The dies and terminals are color coded
to indicate accepted wire range. The dies fit into the
AMP--TAPETRONIC Machine 69875. Refer to
Customer Manual 409--1993.
NOTE
Figures and illustrations are for identification only
and are not drawn to scale.
Read these instructions carefully and completely
before crimping any terminals.
Reasons for reissue of this instruction sheet are
provided in Section 7, REVISION SUMMARY.
2. DESCRIPTION (Figure 1)
Each die assembly consists of a stationary die and a
moving die. The stationary die has a die holding
screw. The moving die has a die holding screw and a
saddle with an assembly screw, and it is marked to
indicate the wire range crimped.
3. DIE INSTALLATION
Prepare the machine to receive dies according to the
instructions in 409--1993 under “Die Replacement”,
and proceed as follows:
1. Position the moving die into the upper crimping
area of the machine and finger tighten the holding
screw.
2. Position the stationary die into the lower
crimping area of the machine and start the holding
screw, but do not tighten it.
3. Hand cycle the machine until the dies bottom
against each other. Tighten both holding screws.
Re--assemble and adjust the machine, again following
the instructions provided in 409--1993.
E 2011 Tyco Electronics Corporation, a TE Connectivity Ltd. Company TOOLING ASSISTANCE CENTER 1--800--722--1111
All Rights Reserved PRODUCT INFORMATION 1--800--522--6752
TE logo is a trademark.
*Trademark. Other product names, logos, or company names might be trademarks of their respective owners.
This controlled document is subject to change.
For latest revision and Regional Customer Service,
visit our website at www.te.com
1 of 4
LOC B
相关PDF资料 |
PDF描述 |
|---|---|
| 81A1A-B28-B25L | POT 1M OHM 5/8" SQ 1/2W PLAS |
| B32529C3563J289 | FILM CAP 0.0560UF 5% 250V |
| 91A1A-B24-D15 | POT 10K OHM 5/8" SQ 1/4W PLAS |
| 1-58166-1 | TOOL SDL FERRULE DIE 6POS |
| 81A1A-B28-B13L | POT 5K OHM 5/8" SQ 1/2W PLAS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 9024020000 | 制造商:Weidmuller 功能描述:SCREWDRIVER, BIT E6.3 -EA - Bulk 制造商:Weidmuller 功能描述:SCREWDRIVER BIT E6.3 |
| 9024-03 | 制造商: 功能描述: 制造商:undefined 功能描述: |
| 9024030000 | 制造商:Weidmuller 功能描述:SCREWDRIVER BITE6,3 0,8X4,0X70 -EA - Bulk 制造商:Weidmuller 功能描述:BIT E6 3 0 8X4 0X70 |
| 9024040000 | 制造商:Weidmuller 功能描述:SCREWDRIVER, BIT E6.3 -EA - Bulk 制造商:Weidmuller 功能描述:SCREWDRIVER BIT E6.3 制造商:Weidmuller 功能描述:ScrewDriver Insert, Slotted, Blade |
| 902-405 | 功能描述:支架与垫片 Plastic Spcr .405 in Nylon White RoHS:否 制造商:Schurter 类型:Transipillar Spacers 长度:16 m 螺纹大小:M4 外径:10 mm 材料:Nylon with Steel 电镀:Zinc |
发布紧急采购，3分钟左右您将得到回复。