- 您现在的位置：买卖IC网 > Datasheet目录611 > 90247-1 (TE Connectivity)TOOL HAND CRIMP SAHT 14-20AWG Datasheet资料下载
参数资料
| 型号： | 90247-1 |
| 厂商： | TE Connectivity |
| 文件页数： | 2/4页 |
| 文件大小： | 0K |
| 描述： | TOOL HAND CRIMP SAHT 14-20AWG |
| 标准包装： | 1 |
| 系列： | Certi-Crimp, MATE-N-LOK |
| 工具类型： | 手动压接器 |
| 适用于相关产品： | 矩形触点，14-20 AWG |
| 特点： | 侧面插入，棘齿 |
i
CERTI-- CRIMP Hand Crimping Tool 90247-- 1
NOTE If using a strip--form contact, the cutoff tabs
MUST meet the dimension requirement stated in
Application Specification 114--1007 or the
customer drawing for the product.
Proceed as follows:
1. Hold the tool so the BACK of the tool (wire side)
is facing you.
2. Ensure that the tool ratchet is released by
squeezing the tool handles and allowing them to
open FULLY.
3. Insert the contact, mating end first, into the
appropriate crimping chamber from the BACK of
the tool. Position the contact between the dies so
that the locator/insulation stop enters the contact
locator slot. See Figure 3.
408-- 7434
Crimp Inspection
Wire Barrel Seam Must Be
Completely Closed With No
Loose Wire Strands
Wire Insulation Must
Not Enter Wire Barrel
End of Wire Must Be Even With
or Protrude Slightly from End of
Wire Barrel
Figure 4
Crimping Contact
NOTE
i
For detailed crimp inspection requirements, refer
to Application Specification 114--1007.
Back of Tool
(Wire Side)
Locator/Insulation
Stop in Contact
Locator Slot
Contact
Support
4. INSULATION CRIMP ADJUSTMENT
The insulation barrel crimp height is regulated by the
insulation crimp adjustment lever. To determine the
proper setting, test crimp a contact using the setting
which approximates the wire insulation size: 1—small,
2—medium, or 3—large. If the crimped insulation
barrel is too tight or too loose, change the setting
accordingly. The crimp should hold the wire insulation
firmly without cutting into it.
5. MAINTENANCE AND INSPECTION
Stripped
Wire
Figure 3
4. Holding the contact in position, squeeze the tool
handles together until the dies close just enough to
hold the contact in place. DO NOT deform contact
wire barrel or insulation barrel.
5. Insert a properly stripped wire into the contact
wire barrel until the wire insulation butts against the
locator/insulation stop.
6. Holding the wire in place, squeeze the tool
handles together until the ratchet releases. Allow
the tool handles to open FULLY.
7. Remove the crimped contact from the tool, and
inspect the crimp according to Figure 4.
The tool is inspected before shipment. The tool
should be inspected immediately upon arrival at your
facility to ensure that the tool was not damaged
during shipment.
5.1. Daily Maintenance
Remove all foreign particles with a clean, soft brush,
or a clean, soft, lint--free cloth. Make sure the proper
retaining pins are in place, and secured with the
proper retaining rings. If foreign matter cannot be
removed easily, or if the proper replacement parts are
not available, refer to Section 6, REPLACEMENT
AND REPAIR, for information on obtaining further
evaluation and repair.
Make certain all pivot points and bearing surfaces are
protected with a THIN coat of any good SAE 20 motor
oil. Do NOT oil excessively. When tool is not in use,
keep the handles closed to prevent objects from
becoming lodged between the dies, and store the tool
in a clean, dry area.
2 of 4
Tyco Electronics Corporation
Rev B
相关PDF资料 |
PDF描述 |
|---|---|
| 90249-2 | DIE TYPE II CONTACTS 69875 |
| 90268-1 | SAHT F CRIMP 24-28 |
| 90270-1 | SAHT F CRIMP 14-18 |
| 90274-2 | SAHT F CRIMP |
| 90276-2 | HHHT PIDG PG FASTON 10-12 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 9024730000 | 制造商:Weidmuller 功能描述:DMSE 0.5X3.0X75 -EA - Bulk |
| 902-475 | 功能描述:支架与垫片 Plastic Spcr .475 in Nylon White RoHS:否 制造商:Schurter 类型:Transipillar Spacers 长度:16 m 螺纹大小:M4 外径:10 mm 材料:Nylon with Steel 电镀:Zinc |
| 9024760000 | 制造商:Weidmuller 功能描述:DMS2 BIT,1/4 ,0.6X3.5X75,SLOT -EA - Bulk |
| 902477 | 制造商:Weidmuller 功能描述: |
| 902478 | 制造商:Weidmuller 功能描述: |
发布紧急采购，3分钟左右您将得到回复。