- 您现在的位置：买卖IC网 > PDF目录18547 > 90391-3 (TE Connectivity)DIE SET ULTRA-FASTONS 16-14 AWG PDF资料下载
参数资料
| 型号： | 90391-3 |
| 厂商： | TE Connectivity |
| 文件页数： | 3/5页 |
| 文件大小： | 0K |
| 描述： | DIE SET ULTRA-FASTONS 16-14 AWG |
| 标准包装： | 1 |
| 系列： | Pro-Crimper III, Faston |
| 压接或电缆尺寸： | 14-16 AWG |
| 压接手柄： | A28005-ND |
| 连接器类型： | 端子及连接件 |
| 产品目录页面： | 375 (CN2011-ZH PDF) |
| 配用： | 8-520125-1-ND - CONN FAST RECEPT 14-16 AWG .187 8-350820-1-ND - CONN ULTRA FAST RCPT 14-16 AWG 8-520129-1-ND - CONN FAST FLG RCPT 18-22AWG .250 8-520133-1-ND - CONN RCPT FLG FAST 16-14AWG .250 8-520107-1-ND - CONN TAB 14-16 AWG .250 8-350816-1-ND - CONN RCEPT 16-14AWG ULTRA-FAST 8-520339-1-ND - CONN RCPT FLG FAST 14-16AWG .187 A27840-ND - CONN FAST FLG RCPT 18-22AWG .250 A27811-ND - CONN FAST RECEPT 14-16 AWG .187 A27824-ND - CONN FAST RECEPT 14-16 AWG .250 更多... |
| 相关产品： | A28005-ND - HAND CRIMP TOOL/FASTOS(W/O DIES) |
| 其它名称： | 90391-3-ND A28008 |
408-9279
Die Retaining
Screw
Die Stop
Setscrew
(Flush on
Both
Sides)
Figure 3
Upper Die
Lower Die
Locator
? For flag terminals, the flat side of the wire end
must face outward and the mating end must seat on
the locator.
7. Squeeze the tool handles sufficiently to hold
the terminal firmly in place without deforming it.
8. Insert a properly stripped wire into the barrel of
the terminal.
9. Hold the wire in place and squeeze the tool
handles until the ratchet releases.
10. Allow the tool handles to open fully, and
remove the crimped terminal.
5. MAINTENANCE/INSPECTION
5.1. Daily Maintenance
Remove all foreign particles with a clean, soft brush or
a clean, soft, lint-free cloth. Do NOT use materials or
objects that can damage the dies. If foreign matter
cannot be removed easily, or if the proper replacement
parts are not available, return the dies to your
supervisor.
Make certain the dies are protected with a THIN coat
of any good SAE 20 motor oil. DO NOT OIL
EXCESSIVELY.
When the dies are not in use, mate and store them in
a clean, dry area.
4. CRIMPING PROCEDURE
1. Refer to the table in Figure 2, select a wire of
the specified size and strip the wire to the
dimension provided. Do NOT nick or cut the wire
strands.
2. Select an applicable contact. See Figure 2.
3. Hold the tool so that the front of the tool is
facing you.
4. Make sure that the ratchet is released.
Squeeze the tool handles together and allow
them to open fully.
5. Rotate the blue plastic locator stop index to the
appropriate position.
? When crimping a 110 series terminal, rotate the
index until the number “110” appears in the
uppermost position.
? When crimping a 187 or 250 series terminal,
rotate the index until the numbers “250-187” appear
in the uppermost position.
Orientation for Tab
and Receptacle
Flat Side of
Wire End
Flat Surface of
Terminal
Front of Tool
(Terminal Side)
Tool Frame
6. Insert the terminal into the proper crimp
section. In-line terminals may be crimped in either
in-line section. Flag terminals must be crimped in
the flag crimp section. See Figure 4.
Orientation for
Flag Terminal
Anvil
Locator
Stop Index
Locator
? For in-line terminals, the flat side of the terminal
must seat on the locator.
Rev E
Figure 4
3 of 5
相关PDF资料 |
PDF描述 |
|---|---|
| YB215CWCKG01-5F12-FB | SWITCH PUSH SPDT 0.4VA 28V |
| DLP31SN121ML2L | CHOKE COMMON MODE 120 OHM 1206 |
| NTB5605PT4 | MOSFET P-CH 60V 18.5A D2PAK |
| A13-1 | TOOL HAND INSERTION FOR T68 |
| NTB4302G | MOSFET N-CH 30V 74A D2PAK |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 90392A028 | 制造商: 功能描述: 制造商:undefined 功能描述: |
| 90393 | 制造商:Distributed By MCM 功能描述:Three Piece Synthetic PaintBrush Set |
| 9039-3419 | 制造商:Leach International Corporation 功能描述:LRE - Bulk |
| 903-935 | 功能描述:支架与垫片 Plastic Spcr .935 in Nylon White RoHS:否 制造商:Schurter 类型:Transipillar Spacers 长度:16 m 螺纹大小:M4 外径:10 mm 材料:Nylon with Steel 电镀:Zinc |
| 903-940 | 功能描述:支架与垫片 Plastic Spcr .94 in Nylon White RoHS:否 制造商:Schurter 类型:Transipillar Spacers 长度:16 m 螺纹大小:M4 外径:10 mm 材料:Nylon with Steel 电镀:Zinc |
发布紧急采购，3分钟左右您将得到回复。