- 您现在的位置：买卖IC网 > Datasheet目录611 > 90575-2 (TE Connectivity)TOOL DIESET 14-20AWG COM-MATE Datasheet资料下载
参数资料
| 型号： | 90575-2 |
| 厂商： | TE Connectivity |
| 文件页数： | 3/6页 |
| 文件大小： | 0K |
| 描述： | TOOL DIESET 14-20AWG COM-MATE |
| 标准包装： | 1 |
| 系列： | MATE-N-LOK II |
| 压接或电缆尺寸： | 14-20 AWG |
| 压接手柄： | A9996-ND |
| 连接器类型： | 压接端子 |
| 产品目录页面： | 229 (CN2011-ZH PDF) |
| 相关产品： | 679304-1-ND - TOOL PNEUMATIC HEAD ASSEMBLY A97885-ND - TOOL HAND CRIMPING SDE PEW 12 A9996-ND - PRO CRIMPER HAND TOOL W/O DIES |
| 其它名称： | A9939 |
i
!
PRO- CRIMPER III Hand Crimping Tool Assembly 90575- 1
2. If adjustment is required, loosen the screw that
holds the contact support onto the locator
assembly.
NOTE The ratchet has detents that create audible clicks
as the tool handles are closed.
i
3. Place a contact with wire into the proper nest
and close the tool handles until the ratchet reaches
the sixth click, or until the contact support touches
the contact.
4. Slightly loosen the nut that holds the locator
assembly onto the tool frame.
5. Move the contact support as required to
eliminate the bending of the contact.
6. Tighten the nut and close the handles until the
ratchet releases.
7. Remove and inspect the contact.
8. Make another sample crimp. If the contact is
straight, tighten the contact support screw. If the
contact is still being bent during crimping, repeat
the adjustment procedure.
5. CRIMPING PROCEDURE
NOTE This tool is provided with a crimp adjustment
feature. Initially, the crimp height should be
verified as specified in Figure 4. Refer to
Section 6, CRIMP HEIGHT INSPECTION, and
Section 7, RATCHET ADJUSTMENT, to verify
crimp height before using the tool to crimp
desired contacts and wire sizes.
408- 9887
Refer to the table in Figure 1 and select wire of the
specified size and insulation diameter. Strip the wire
to the length indicated in Figure 1, taking care not to
nick or cut wire strands. Select an applicable contact
and identify the appropriate crimp section according
to the wire size markings on the tool. Refer to
Figure 3 and proceed as follows:
1. Hold the tool so that the back (wire side) is
facing you. Squeeze tool handles together and
allow them to open fully.
2. Holding the contact by the mating end, insert the
contact — insulation barrel first — through the front
of the tool and into the appropriate crimp section.
3. Position the contact so that the mating end of
the contact is on the locator side of the tool, and so
that the open “U” of the wire and insulation barrels
face the top of the tool. Place the contact up into
the nest so that the movable locator drops into the
slot in the contact. Refer to Figure 3. Butt the front
end of the wire barrel against the movable locator.
CAUTION Make sure that both sides of the insulation barrel
are started evenly into the crimping section. Do
NOT attempt to crimp an improperly positioned
contact.
4. Hold the contact in position and squeeze the
tool handles together until ratchet engages
sufficiently to hold the contact in position. Do NOT
deform insulation barrel or wire barrel.
Contact
Support
Locator
Adjustment
Screw for
Contact Support
Back of Tool
(Wire Side)
Wire
Contact
(Typ)
Locator in
Wire Stop Slot
Strip
Length
Wire Inserted
to Stop
Figure 3
Rev C
Tyco Electronics Corporation
3 of 6
相关PDF资料 |
PDF描述 |
|---|---|
| 90652-1 | PRO-CRIMPER ASSY MULTILOCK |
| 90654-2 | PROCRIMPER DIE ASSY MULTILOCK |
| 90682-2 | PROCRIMPER DIE ASSY DYNAMIC |
| 90683-2 | PROCRIMPER DIE ASSY DYNAMIC |
| 90684-2 | PROCRIMPER DIE ASSY DYNAMIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 905-755 | 功能描述:支架与垫片 Plastic Spcr .755 in Nylon White RoHS:否 制造商:Schurter 类型:Transipillar Spacers 长度:16 m 螺纹大小:M4 外径:10 mm 材料:Nylon with Steel 电镀:Zinc |
| 905759-0002 | 制造商: 功能描述: 制造商:undefined 功能描述: |
| 905759-2 | 制造商: 功能描述: 制造商:undefined 功能描述: |
| 905-760 | 功能描述:支架与垫片 Plastic Spcr .76 in Nylon White RoHS:否 制造商:Schurter 类型:Transipillar Spacers 长度:16 m 螺纹大小:M4 外径:10 mm 材料:Nylon with Steel 电镀:Zinc |
| 905760-0002 | 制造商: 功能描述: 制造商:undefined 功能描述: |
发布紧急采购，3分钟左右您将得到回复。