- 您现在的位置：买卖IC网 > PDF目录19180 > 90683-1 (TE Connectivity)PRO-CRIMPER ASSEMBLY PDF资料下载
参数资料
| 型号： | 90683-1 |
| 厂商： | TE Connectivity |
| 文件页数： | 4/6页 |
| 文件大小： | 0K |
| 描述： | PRO-CRIMPER ASSEMBLY |
| 标准包装： | 5 |
| 系列： | Pro-Crimper III 型，动态 D-3000 |
| 工具类型： | 手动压接器 |
| 适用于相关产品： | 矩形触点，20-24 AWG |
| 特点： | 侧面插入，棘齿 |
| 配用： | A29250-ND - CONN TAB 20-24AWG CRIMP TIN A29249-ND - CONN TAB 20-24AWG CRIMP 30GOLD A29248-ND - CONN TAB 20-24AWG CRIMP 15GOLD A29224-ND - CONN RCPT 20-24AWG CRIMP TIN A29223-ND - CONN RCPT 20-24AWG CRIMP 30GOLD A29222-ND - CONN RCPT 20-24AWG CRIMP 15GOLD A29221-ND - CONN RCPT 20-24AWG CRIMP 30GOLD A29220-ND - CONN RCPT 20-24AWG CRIMP 15GOLD |
PRO- CRIMPER III Hand Crimping Tool Assembly 90683- 1
4. Hold the contact in position and squeeze the
tool handles together until ratchet engages
sufficiently to hold the contact in position. Do NOT
deform insulation barrel or wire barrel.
5. Insert stripped wire into contact insulation and
wire barrels until it is butted against the wire stop,
as shown in Figure 3.
6. Holding the wire in place, squeeze tool handles
together until ratchet releases. Allow tool handles
to open and remove crimped contact.
408- 9935
2. Refer to Section 5, CRIMPING PROCEDURE,
and crimp the contact(s) accordingly.
3. Using a crimp height comparator, measure the
wire barrel crimp height as shown in Figure 4. If the
crimp height conforms to that shown in the table,
the tool is considered dimensionally correct. If not,
the tool must be adjusted. Refer to Section 7,
RATCHET (Crimp Height) ADJUSTMENT.
7. RATCHET (Crimp Height) ADJUSTMENT (Figure 5)
NOTE
i
The crimped contact may stick in the crimping
area, but the contact can be easily removed by
pushing downward on the top of the locator (see
Figure 3).
1. Remove the lockscrew from the ratchet
adjustment wheel.
Screwdriver
7. Check the contact’s crimp height as described in
Section 6, CRIMP HEIGHT INSPECTION. If
necessary, adjust the crimp height as described in
Section 7, RATCHET (Crimp Height)
ADJUSTMENT.
6. CRIMP HEIGHT INSPECTION
Crimp height inspection is performed through the use
of a micrometer with a modified anvil, commonly
referred to as a crimp--height comparator. Tyco
Electronics does not manufacture or market
crimp--height comparators. Detailed information on
obtaining and using crimp--height comparators can be
found in instruction sheet 408--7424.
Proceed as follows:
Ratchet
Adjustment
Wheel
Lockscrew
(Typ)
1. Refer to Figure 4 and select a wire (maximum
size) for each crimp section listed.
Position Point
on Center of
Wire Barrel
Opposite
Seam
Modified Anvil “A”
Figure 5
2. With a screwdriver, adjust the ratchet wheel
from the locator side of the tool.
3. Observe the ratchet adjustment wheel. If a
tighter crimp is required, rotate the adjustment
wheel COUNTERCLOCKWISE to a
higher--numbered setting. If a looser crimp is
required, rotate the adjustment wheel
CLOCKWISE to a lower--numbered setting.
4. Replace the lockscrew.
Wire Size
AWG (Max)
22
20
Crimp Section
(Wire Size Marking)
24--22
20
Crimp Height
Dimension A
(and Tolerance + )
1.02 + .07
[ .040 + .003]
1.17 + .07
[.046 + .003]
5. Make a sample crimp and measure the crimp
height. If the dimension is acceptable, replace and
secure the lockscrew. If the dimension is
unacceptable, continue to adjust the ratchet, and
again measure a sample crimp.
Figure 4
4 of 6
Tyco Electronics Corporation
Rev C
相关PDF资料 |
PDF描述 |
|---|---|
| 229451-2 | PALM GRIP TOOL & 50 POSN SLIDE |
| 58499-1 | TOOL PRO CRIMPER II W/DI |
| A6S-7104-PH | SWITCH DIP 7POS RAISED SMD |
| 5370T1LC | LED RED T-3/4 VERT LOW CUR PCB |
| DP04T | PIANO STYLE DIP SWITCH |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 90683-2 | 功能描述:折皱器 PROCRIMPER DIE ASSY DYNAMIC RoHS:否 制造商:Hirose Connector 类型: 描述/功能:Cable and Shield Crimper |
| 906-835 | 功能描述:支架与垫片 Plastic Spcr .835 in Nylon White RoHS:否 制造商:Schurter 类型:Transipillar Spacers 长度:16 m 螺纹大小:M4 外径:10 mm 材料:Nylon with Steel 电镀:Zinc |
| 90684 | 制造商:OMRON INDUSTRIAL AUTOMATION 功能描述:2814 |
| 906-840 | 功能描述:支架与垫片 Plastic Spcr .84 in Nylon White RoHS:否 制造商:Schurter 类型:Transipillar Spacers 长度:16 m 螺纹大小:M4 外径:10 mm 材料:Nylon with Steel 电镀:Zinc |
| 90684-1 | 功能描述:折皱器 PRO-CRIMPER ASSY RoHS:否 制造商:Hirose Connector 类型: 描述/功能:Cable and Shield Crimper |
发布紧急采购，3分钟左右您将得到回复。