- 您现在的位置：买卖IC网 > PDF目录19195 > 90870-1 (TE Connectivity)TOOL CRIMP .062 AWG 30 W/DIE PDF资料下载
参数资料
| 型号： | 90870-1 |
| 厂商： | TE Connectivity |
| 文件页数： | 3/6页 |
| 文件大小： | 0K |
| 描述： | TOOL CRIMP .062 AWG 30 W/DIE |
| 标准包装： | 1 |
| 系列： | Pro-Crimper III，商用 0.062" |
| 工具类型： | 手动压接器 |
| 适用于相关产品： | 矩形触点，24-30 AWG |
| 特点： | 侧面插入，棘齿 |
| 产品目录页面： | 240 (CN2011-ZH PDF) |
| 配用： | A14048-ND - CONN SOCKET 24-30AWG TIN CRIMP A14016-ND - CONN PIN 24-30AWG TIN CRIMP |
| 其它名称： | A9819 |
PRO- CRIMPER III Hand Crimping Tool Assembly 90870- 1
4. CONTACT SUPPORT ADJUSTMENT (Figure 3)
5. CRIMPING PROCEDURE
408- 9965
NOTE The contact support is preset prior to shipment,
but minor adjustment may be necessary.
i
1. Make a sample crimp and determine if the
contact is straight, bending upward, or bending
downward.
NOTE
i
This tool is provided with a crimp adjustment
feature. Initially, the crimp height should be
verified as specified in Figure 4. Refer to
Section 6, CRIMP HEIGHT INSPECTION, and
Section 7, RATCHET ADJUSTMENT, to verify
crimp height before using the tool to crimp
desired contacts and wire sizes.
2. If adjustment is required, loosen the screw that
holds the contact support onto the locator
assembly.
NOTE The ratchet has detents that create audible clicks
as the tool handles are closed.
i
3. Place a contact with wire into the proper nest
and close the tool handles until the ratchet reaches
the sixth click, or until the contact support touches
the contact.
4. Slightly loosen the nut that holds the locator
assembly onto the tool frame.
5. Move the contact support as required to
eliminate the bending of the contact.
6. Tighten the nut and close the handles until the
ratchet releases.
7. Remove and inspect the contact.
Refer to the table in Figure 1 and select wire of the
specified size and insulation diameter. Strip the wire
to the length indicated in Figure 1, taking care not to
nick or cut wire strands. Select an applicable contact
and identify the appropriate crimp section according
to the wire size markings on the tool. Refer to
Figure 3 and proceed as follows:
1. Hold the tool so that the back (wire side) is
facing you. Squeeze tool handles together and
allow them to open fully.
2. Holding the contact by the mating end, insert the
contact — insulation barrel first — through the front
of the tool and into the appropriate crimp section.
3. Position the contact so that the mating end of
the contact is on the locator side of the tool, and so
that the open “U” of the wire and insulation barrels
face the top of the tool. Place the contact up into
the nest so that the movable locator drops into the
slot in the contact. Refer to Figure 3. Butt the front
end of the wire barrel against the movable locator.
8. Make another sample crimp. If the contact is
straight, tighten the contact support screw. If the
contact is still being bent during crimping, repeat
the adjustment procedure.
Contact
Locator
Support
CAUTION
!
Make sure that both sides of the insulation barrel
are started evenly into the crimping section. Do
NOT attempt to crimp an improperly positioned
contact.
Adjustment
Screw for
Contact
Support
Back of Tool
(Wire Side)
Wire
Contact
(Typ)
Locator
in Wire
Stop Slot
Strip
Length
Wire
Inserted
to Stop
Figure 3
Rev C
Tyco Electronics Corporation
3 of 6
相关PDF资料 |
PDF描述 |
|---|---|
| 90871-1 | PROCRIMPER III W/DIE 14-20AWG |
| 90869-1 | TOOL CRIMP .062 AWG 24 W/DIE |
| 210-5MSD | SWITCH RAISED ACTUATOR 5 SEC |
| 210-5LPSD | SWITCH SPST 5 SEC STRAIGHT TERM |
| 210-5ESF | SWITCH EXTENDED ACTUATOR 5 SEC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 908701-000 | 制造商:TE Connectivity 功能描述:Bullet Terminal 14-16AWG M 34mm 4.6mm Tin Loose Piece 制造商:TE Connectivity 功能描述:SNAP TERMINAL 14-16AWG M 34.54MM 5.08MM TN LOOSE PIECE - Bulk 制造商:TE Connectivity 功能描述:CONN PLUG 14-16AWG DURASEAL 制造商:TE Connectivity 功能描述:B-106-7502 |
| 90870-2 | 功能描述:冲压机与冲模 COMM .062 PIN/SOC PROCRIMP DIE RoHS:否 制造商:Souriau 大小: 产品:Dies 类型:Crimping 描述/功能: |
| 908-7028-2HZ | 制造商:Amphenol RF 功能描述:MALE CONTACT |
| 90870314 | 制造商:Western Auto 功能描述: |
| 908-705 | 功能描述:支架与垫片 Plastic Spcr .705 in Nylon White RoHS:否 制造商:Schurter 类型:Transipillar Spacers 长度:16 m 螺纹大小:M4 外径:10 mm 材料:Nylon with Steel 电镀:Zinc |
发布紧急采购，3分钟左右您将得到回复。