- 您现在的位置：买卖IC网 > Datasheet目录612 > 91117-1 (TE Connectivity)TOOL CLINCHING Datasheet资料下载
参数资料
| 型号： | 91117-1 |
| 厂商： | TE Connectivity |
| 文件页数： | 2/2页 |
| 文件大小： | 0K |
| 描述： | TOOL CLINCHING |
| 标准包装： | 5 |
| 系列： | * |
end of the connector and number–coded on the
other end.
2. Place the key into the cavity at the desired
position. Insert the rivet into the back of the cavity
with the flat edge against the connector.
3. Open the tool handles, and position the tool
perpendicular to the connector.
4. Place the lower jaw on the rivet, and close the
tool punch tip through the key and into the rivet.
5. Squeeze the tool handles together until the jaws
are bottomed. Remove the tool and, if required,
repeat these procedures on the other end of the
connector.
Remove all foreign particles with a clean, soft brush
or a clean, soft, lint–free cloth. Make sure the proper
retaining pins are in place and are secured with the
proper retaining rings.
Make sure all pivot points and bearing surfaces are
protected with a thin coat of any good SAE 20 motor
oil. DO NOT oil excessively.
It is recommended that the tool be inspected upon
arrival at your facility, and at regularly scheduled
intervals, to ensure that the tool has not been
damaged during handling.
Though recommendations call for at least one
inspection a month, the inspection frequency should
be based on the amount of use, ambient working
conditions, operator training and skill, and established
company standards.
Customer–replaceable parts are listed in Figure 3.
Order replacement parts through your representative,
or call 1–800–526–5142, or send a facsimile of your
purchase order to 717–986–7605, or write to:
CUSTOMER SERVICE (038–035)
TYCO ELECTRONICS CORPORATION
PO BOX 3608
HARRISBURG PA 17105–3608
For customer repair service, call 1–800–526–5136.
Revisions to this instruction sheet include:
Updated document to corporate requirements
Removed obsolete connector part number
Figure 3
相关PDF资料 |
PDF描述 |
|---|---|
| 91117-6 | TOOL CLINCHING |
| 91136-1 | TOOL EXTRACTION CONTACT DIN |
| 91144-1 | CONTACT EXTRACTION TOOL |
| 91156-1 | EXTRACTION TOOL |
| 91164-2 | AMPLIMITE INS TOOL 9 POS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 91117-2 | 功能描述:手工工具 TOOL CLINCHING RoHS:否 制造商:Molex 产品:Extraction Tools 类型: 描述/功能:Extraction tool |
| 9111-72 BLK | 功能描述:PATCHCORD BANA PLUG STKG 72" BLK RoHS:是 类别:测试设备 >> 测试引线 - 香蕉，量表接口 系列:9111 标准包装:1 系列:6570 类型:插接线 配置:香蕉插头至短头鳄鱼夹 第一连接器:香蕉插头，单，屏蔽，直角 第二连接器:接线夹，隔离型，特大号 线缆长度:60.0"（1524.00mm） 所含物品:1 根引线，红 材料 - 绝缘体:硅树脂 堆叠方法:不可堆叠 线规:18 AWG 电压 - 额定:1000V（1kV） 额定电流:20A 额定值:CAT III 1000V，IEC 1010 |
| 9111-72 RED | 功能描述:PATCHCORD BANA PLUG STKG 72" RED RoHS:是 类别:测试设备 >> 测试引线 - 香蕉，量表接口 系列:9111 标准包装:1 系列:6570 类型:插接线 配置:香蕉插头至短头鳄鱼夹 第一连接器:香蕉插头，单，屏蔽，直角 第二连接器:接线夹，隔离型，特大号 线缆长度:60.0"（1524.00mm） 所含物品:1 根引线，红 材料 - 绝缘体:硅树脂 堆叠方法:不可堆叠 线规:18 AWG 电压 - 额定:1000V（1kV） 额定电流:20A 额定值:CAT III 1000V，IEC 1010 |
| 9111-72-S | 功能描述:PATCHCORD BANA PLUG SET/10 72" RoHS:是 类别:测试设备 >> 测试引线 - 香蕉，量表接口 系列:9111 标准包装:1 系列:6570 类型:插接线 配置:香蕉插头至短头鳄鱼夹 第一连接器:香蕉插头，单，屏蔽，直角 第二连接器:接线夹，隔离型，特大号 线缆长度:60.0"（1524.00mm） 所含物品:1 根引线，红 材料 - 绝缘体:硅树脂 堆叠方法:不可堆叠 线规:18 AWG 电压 - 额定:1000V（1kV） 额定电流:20A 额定值:CAT III 1000V，IEC 1010 |
| 91117-3 | 功能描述:手工工具 TOOL HAND RoHS:否 制造商:Molex 产品:Extraction Tools 类型: 描述/功能:Extraction tool |
发布紧急采购，3分钟左右您将得到回复。