- 您现在的位置：买卖IC网 > PDF目录19055 > 91313-2 (TE Connectivity)6 ROW HS3 SEATING TOOL ASSY PDF资料下载
参数资料
| 型号： | 91313-2 |
| 厂商： | TE Connectivity |
| 文件页数： | 2/3页 |
| 文件大小： | 0K |
| 描述： | 6 ROW HS3 SEATING TOOL ASSY |
| 标准包装： | 1 |
| 系列： | * |
408-4546
Damage to the pc board, seating tool, or header
!
Do not use damaged or defective headers. ?
?
!
For Seating Tools -1 (not keyed), make sure that
the grounding arrow is pointing toward the end row
i
3.2. PC Board Support Fixture (Customer Supplied)
A pc board support must be used to provide proper
support for the pc board and alignment of the seating
tool to the header, and to protect the pc board and
header contacts from damage. Design a pc board
support fixture using the recommendations in
Instruction Sheet 408-6927.
4. SEATING
1. Set the seating height to the dimension shown in
seating height PLUS the combined thicknesses of
the pc board and pc board support).
2. Position the header onto pc board so that the
header contact posts are properly aligned with the
holes in the pc board and pc board support.
3. Insert the header onto the pc board until the post
sections of the contacts are resting securely on, but
have not fully entered, the pc board.
4. Position the appropriate seating tool into the
header, making sure that the seating tool is
bottomed on the housing floor.
NOTE
of ground blades of the header. ?
Seating Height
(Header Seated)
38.1 +.254/-0.00
[1.500 +.010/-.000]
5. Center the seating tool and header under the
applicator ram of the applicator; slowly lower the
ram until it just meets the seating tool. Verify the
alignment of the pc board support, pc board,
header, and seating tool.
CAUTION
may occur if the wrong size seating tool is used, the
seating height is improperly set, the grounding
arrow (for Seating Tools -1) is oriented incorrectly,
or the seating tool is not properly seated in the
header before cycling the ram.
6. Cycle the applicator. Check the header for proper
seating using the requirements in the Application
Specification 114-13020.
7. Remove the pc board with the seated header or
reposition the pc board and pc board support to
seat additional headers.
CAUTION
?
5. MAINTENANCE AND INSPECTION
5.1. Initial Inspection
Each seating tool is assembled and inspected before
shipment. It is recommended that the seating tool be
inspected using Figure 3 immediately upon arrival to
ensure that it has not been damaged during shipment.
Applicator Ram
(Fully Down) (Ref)
Seating Tool Centered
Under Ram
Seating Tool Inside Header
Housing and Bottomed on
Housing Floor
Applicator
Shut Height
(Ram Down)
0.00-0.254 [.000-.010]
(Single Plane Application)
0.10 [.004] Max
(Mid-Plane Application)
Contact Posts Aligned with Holes in
PC Board and PC Board Support
Allowable Gap
PC Board
PC Board Support
Figure 2
Rev B
2 of 3
相关PDF资料 |
PDF描述 |
|---|---|
| 58274-3 | SEATING TOOL ACTION PIN 9POS |
| LP0005/01-LI98-0.15 | LI98 FOR LXK8-PWXX-0016 & 0012 |
| LP0004/01-LI98-0.15 | LI98 FOR LXK8-PWXX-0008 |
| LP0003/01-LI98-0.15 | LI98 FOR LXK8-PWXX-0004 |
| HS-4150-0345 | HEATSINK 1.5" FOR BL-2000/4000 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 913-133 | 制造商:SPC Multicomp 功能描述:CAPACITOR 470UF 35V |
| 913-135 | 功能描述:支架与垫片 Plastic Spcr .135 in Nylon White RoHS:否 制造商:Schurter 类型:Transipillar Spacers 长度:16 m 螺纹大小:M4 外径:10 mm 材料:Nylon with Steel 电镀:Zinc |
| 913139 | 制造商:ERNI Electronics 功能描述:C64FACVV5-00EE3017.0*K307E018* 制造商:Phoenix Contact 功能描述:H 6 A 制造商:ERNI Electronics 功能描述:913139 / C 64 F AC VV 5-00 EE30 / DIN F |
| 913-13MM | 功能描述:支架与垫片 Plastic Spcr 13mm Nylon White RoHS:否 制造商:Schurter 类型:Transipillar Spacers 长度:16 m 螺纹大小:M4 外径:10 mm 材料:Nylon with Steel 电镀:Zinc |
| 9131-4 | 制造商:Multi Contact AG 功能描述:SOCKET 4MM SHROUDED YELLOW |
发布紧急采购，3分钟左右您将得到回复。