- 您现在的位置：买卖IC网 > Datasheet目录613 > 91318-1 (TE Connectivity)12 ROW RECPT SEAT TOOL Datasheet资料下载
参数资料
| 型号： | 91318-1 |
| 厂商： | TE Connectivity |
| 文件页数： | 2/3页 |
| 文件大小： | 0K |
| 描述： | 12 ROW RECPT SEAT TOOL |
| 标准包装： | 1 |
| 系列： | * |
!
i
Seating Tools 91318-- [ ], 91319-- [ ], and 91320-- [ ]
3.2. Application Tooling
Power for the seating tool must be provided by a
machine capable of supplying a downward force of
89 Newtons (N) [20 lb] per contact. Manual Electric
Servo Press (MEP 6T) 2--1399500--5 and Bench Top
Electric Servo Presses (BMEP 3T) 1--1399400--5 and
(BMEP 5T) 2--1399401--4 are available for this
seating tool. For information on the presses, visit the
press--fit assembly equipment website at
http://tooling.tycoelectronics.com/pressfit.asp .
4. SEATING
1. Set seating height to the dimension shown in
Figure 2 (applicator shut height will equal the
seating height PLUS the combined thicknesses of
the pc board, and pc board support fixture).
2. Position the connector onto the pc board so that
the contacts are properly aligned with the holes in
the pc board and the holes or slots in the pc board
support fixture. See Figure 2.
3. Sit the connector onto the pc board until the tips
of the contacts are resting securely on, but have
not fully entered, the holes in the pc board.
408-- 4571
meets the seating tool. Verify the alignment of the
pc board support fixture, pc board, connector, and
seating tool.
CAUTION Damage to the pc board, seating tool, or
connector may occur if seating height is
improperly set, if the pc board is not properly
positioned with the seating tool, or if the seating
tool is not properly seated on the connector
before cycling the applicator ram.
6. Cycle the applicator ram according to
instructions for the application tooling.
7. Remove the pc board with the seated connector,
and check the connector for proper seating
according to the following:
a. the widest section of each contact is inside its
intended pc board hole
b. the connector is seated on the pc board with
the seating height given in Figure 2.
NOTE For detailed inspection requirements of the
seated connector assembly, refer to Application
Specification 114--13020.
4. Position the seating tool onto the connector with
the slanted surface oriented as shown in Figure 2.
5. Center the seating tool and connector under the
applicator ram, and slowly lower the ram until it just
CAUTION
!
A damage connector should not be used. If a
damaged connector is evident, it should be
removed from the pc board and replaced with a
new one.
View After Seating
Applicator Ram
(Fully Down)
Applicator
Shut Height
(Ram Down)
Seating Height
(Connector Seated)
38.1 [1.50]
PC Board
Figure 2
Seating Tool Centered
Under Applicator Ram and
Bottomed on Connector
Contacts in PC Board Holes
and Holes or Grooves in
PC Board Support Fixture
PC Board Support Fixture
(Customer Supplied)
2 of 3
Tyco Electronics Corporation
Rev A
相关PDF资料 |
PDF描述 |
|---|---|
| 91327-1 | SEAT TL 2MM HM UP SHLD TYPE F |
| 91333-1 | VS-3 HANDLE KIT |
| 91338-1 | 0.64 MM CONTACT PRO-CRIMPER |
| 91338-2 | TOOL HAND PRO CRIMPER 20-18AWG |
| 91346-1 | 2MM HM SEATING TOOL TYPE AB 25 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 9-1318118-8 | 功能描述:DYNAMIC D-2100 REC HSG 16P Y-KEY 制造商:te connectivity amp connectors 系列:* 零件状态:有效 标准包装:1,600 |
| 9-1318118-9 | 制造商:TE Connectivity 功能描述:DYNAMIC 2100D REC 20P DBL Y NATURAL |
| 9-1318119-3 | 制造商:TE CONNECTIVITY 功能描述:DYNAMIC 2100D REC HSG 6P Y NATURAL 制造商:TE Connectivity 功能描述:DYNAMIC 2100D REC HSG 6P Y NATURAL |
| 9-1318124-2 | 功能描述:6 位 接头，有罩 连接器 0.098"（2.50mm） 通孔 金 制造商:te connectivity amp connectors 系列:动态 D-2100 包装:管件 零件状态:有效 触头类型:公形引脚 连接器类型:接头，有罩 针脚数:6 加载的针脚数:全部 间距:0.098"（2.50mm） 排数:2 排距:0.148"（3.75mm） 触头配接长度:- 安装类型:通孔 端接:焊接 紧固类型:- 特性:板锁 触头镀层:金 触头镀层厚度:15μin（0.38μm） 颜色:自然色 标准包装:46 |
| 9-1318126-2 | 制造商:TE CONNECTIVITY 功能描述:DYNAMIC 2100D HDR ASSY V 12P Y NATURAL |
发布紧急采购，3分钟左右您将得到回复。