- 您现在的位置：买卖IC网 > Datasheet目录613 > 91349-4 (TE Connectivity)SEATING TL HDR 4 PR 20 COL Datasheet资料下载
参数资料
| 型号： | 91349-4 |
| 厂商： | TE Connectivity |
| 文件页数： | 2/4页 |
| 文件大小： | 0K |
| 描述： | SEATING TL HDR 4 PR 20 COL |
| 标准包装： | 1 |
| 系列： | * |
!
!
i
Seating Tools 91348- [ ], 91349- [ ], and 91375- [ ]
3.2. Application Tooling
Power for seating tools must be provided by a
machine capable of supplying a downward force of
45 Newtons (N) [10 lb] per contact. Manual Electric
Servo Press (MEP 6T) 1585699--1, Bench Top
Electric Servo Presses (BMEP 3T) 1585697--1, and
(BMEP 5T) 1585696--1 are available for this seating
tool. For information on the presses, visit the press--fit
assembly equipment website at
http://tooling.tycoelectronics.com/pressfit.asp .
CAUTION Over--driving of the connector will deform parts
critical to the quality of the connection. Maximum
force occurs prior to the connector bottoming on
the pc board.
4. SEATING
1. Set seating height to the dimension shown in
Figure 2 (application tool shut height will equal the
tool seating height PLUS the combined
thicknesses of the pc board and support fixture).
After seating, a gap of no more than 0.10 mm
[.004 in.] between the connector standoffs and the
pc board is allowed.
NOTE The seating height of 38.1 mm [1.50 in.] is a
reference starting point. Seating height may need
adjusted to obtain the 0.1 mm [.004 in.]
maximum gap between the connector and the pc
board.
Note: Not to Scale
408- 8501
2. Position the connector on the pc board so that
contacts are properly aligned with the holes in the
pc board and pc board support fixture.
3. Sit the connector onto pc board until the open
section of the contacts are resting securely on, but
have not fully entered, the holes in the pc board.
4. Orient the key(s) of the blade with the groove(s)
on the inside of the connector housing, then
position the seating tool onto the connector,
making sure the blade bottoms on the housing
floor.
CAUTION Damage to the pc board, seating tool, or
connector may occur if the wrong seating tool is
used, if the seating height is improperly set, or if
the seating tool is not properly seated in the
connector before cycling the ram. DO NOT use
damaged product.
5. Center the seating tool (with the connector)
under the ram of the applicator tool; and slowly
lower the ram until it just meets the seating tool.
Verify alignment of the pc board support fixture, pc
board, connector, and seating tool.
6. Cycle the ram according to instructions included
with the application tooling. Check the connector
for proper seating using the requirements in
Application Specification 114--13059.
7. Remove the pc board or reposition the pc board
and pc board support fixture for seating additional
connectors.
Applicator Ram (Fully Down)
(Ref)
Seating Tool
Applicator Tooling
Shut Height
(Ram Down)
Seating Height
(Connector Seated)
38.1 [1.50] Ref
Maximum
Gap Allowed
0.10 [.004]
Figure 2
Blade Inside Connector
Housing and Bottomed on
Housing Floor
Contacts in Holes in PC Board
and PC Board Support
PC Board
PC Board Support Fixture
2 of 4
Tyco Electronics Corporation
Rev G
相关PDF资料 |
PDF描述 |
|---|---|
| 91360-1 | SEATING TL 2MM HM TYPE M |
| 91369-2 | PRO-C DIE SL156 16 |
| 91376-1 | SEATING TL RCPT HMZD 3 PR |
| 91391-2 | SDE ERGO DIE MICRO MNL |
| 913923-1 | EXTRACTON TOOL FOR 175150 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 913-495 | 功能描述:支架与垫片 Plastic Spcr .495 in Nylon White RoHS:否 制造商:Schurter 类型:Transipillar Spacers 长度:16 m 螺纹大小:M4 外径:10 mm 材料:Nylon with Steel 电镀:Zinc |
| 9134D | 功能描述:WR RAT COMB 34MM 制造商:apex tool group 系列:* 零件状态:在售 标准包装:10 |
| 913-4MM | 功能描述:支架与垫片 Plastic Spcr 4mm Nylon White RoHS:否 制造商:Schurter 类型:Transipillar Spacers 长度:16 m 螺纹大小:M4 外径:10 mm 材料:Nylon with Steel 电镀:Zinc |
| 9135 | 制造商:Abbatron/HH Smith 功能描述:Standoff; #2-56; 0.437 in.; 1/4 in.; Hex; Brass 制造商:Abbatron/HH Smith 功能描述:Standoffs Hex F/F 0.187in 0.187in 2-56 0.437in Brass Nickel |
| 9135 WAF | 制造商:Fairchild Semiconductor Corporation 功能描述: |
发布紧急采购，3分钟左右您将得到回复。