- 您现在的位置：买卖IC网 > Datasheet目录613 > 91360-1 (TE Connectivity)SEATING TL 2MM HM TYPE M Datasheet资料下载
参数资料
| 型号： | 91360-1 |
| 厂商： | TE Connectivity |
| 文件页数： | 2/3页 |
| 文件大小： | 0K |
| 描述： | SEATING TL 2MM HM TYPE M |
| 标准包装： | 1 |
| 系列： | * |
When setting up equipment to seat connectors, pay
particular attention to the following:
— The seating tool must be matched to the
connector
— The seating tool, connector, and applicator ram
must be properly aligned before cycling the tool
6. Cycle the tool to seat the connector in the pc
board. Then retract the ram, and carefully remove
the seating tool. Check to make sure that the
connector has been properly seated.
7. Repeat Steps 2 through 6 until all connectors
are seated.
1. Set seating height to the dimension shown in
Figure 2 (applicator shut height will equal the
seating height PLUS the combined thicknesses of
the pc board and pc board support fixture).
2. Position the connector onto pc board so that the
contacts (and alignment features) are properly
aligned to the pc board and support fixture.
3. Place the connector onto pc board until the
contacts are resting securely on, but have not fully
entered, the pc board.
4. Position the seating tool onto the connector,
making sure that the tool is bottomed on the
housing floor.
5. Center the seating tool and connector under the
applicator ram of the tool. Slowly lower the ram
until it just meets the seating tool. Verify alignment
of the support fixture, pc board, connector, and
seating tool.
The seating tool is assembled and inspected before
shipment. It is recommended that the tool be
inspected immediately upon arrival at your facility to
ensure that the tool has not been damaged during
shipment.
It is recommended that each operator be made aware
of, and responsible for, the following steps of daily
maintenance:
1. Remove dust, moisture, and contaminants with
a clean, soft brush or a lint–free cloth. DO NOT
use objects that could damage the tool
components.
Figure 2
相关PDF资料 |
PDF描述 |
|---|---|
| 91369-2 | PRO-C DIE SL156 16 |
| 91376-1 | SEATING TL RCPT HMZD 3 PR |
| 91391-2 | SDE ERGO DIE MICRO MNL |
| 913923-1 | EXTRACTON TOOL FOR 175150 |
| 91411-2 | MASS TERMINATION APPLICATOR |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 913-601 | 制造商:SPC Multicomp 功能描述:CAPACITOR 105C 10UF 25V |
| 913605 | 制造商:Phoenix Contact 功能描述:Fuse Terminal Block |
| 913-605 | 功能描述:支架与垫片 Plastic Spcr .605 in Nylon White RoHS:否 制造商:Schurter 类型:Transipillar Spacers 长度:16 m 螺纹大小:M4 外径:10 mm 材料:Nylon with Steel 电镀:Zinc |
| 913606 | 制造商:ERNI Electronics 功能描述:M24-8MABCVVV3-000606**207UP019999 制造商:ERNI Electronics 功能描述:913606 / M 24-8 M ABC VVV 3-00 0606 / M SERIES |
| 913607 | 制造商:ERNI Electronics 功能描述:M24-8FABCVVV2-00060604.0*207EP019999 制造商:ERNI Electronics 功能描述:913607 / M 24-8 F ABC VVV 2-00 0606 / M SERIES |
发布紧急采购，3分钟左右您将得到回复。