- 您现在的位置：买卖IC网 > PDF目录122717 > 9173B-01CS08LFT (INTEGRATED DEVICE TECHNOLOGY INC) 75 MHz, VIDEO CLOCK GENERATOR, PDSO8 PDF资料下载
参数资料
| 型号： | 9173B-01CS08LFT |
| 厂商： | INTEGRATED DEVICE TECHNOLOGY INC |
| 元件分类： | 时钟产生/分配 |
| 英文描述： | 75 MHz, VIDEO CLOCK GENERATOR, PDSO8 |
| 封装： | 0.150 INCH, ROHS COMPLIANT, SOIC-8 |
| 文件页数： | 3/9页 |
| 文件大小： | 303K |
| 代理商： | 9173B-01CS08LFT |
IDT9173B
VIDEO GENLOCK PLL
CLOCK SYNTHESIZER
IDT VIDEO GENLOCK PLL
3
IDT9173B
REV B 111209
Using the IDT9173B in Genlock Applications
Most video sources, such as video cameras, are
asynchronous, free-running devices. To digitize video or
synchronize one video source to another free-running
reference video source, a video “genlock” (generator lock)
circuit is required. The IDT9173B integrates the analog
blocks which make the task much easier.
In the complete video genlock circuit, the primary function of
the IDT9173B is to provide the analog circuitry required to
generate the video dot clock within a PLL. This application
is illustrated in Figure 1. The input reference signal for this
circuit is the horizontal synchronization (H-SYNC) signal. If
a composite video reference source is being used, the
h-sync pulses must be separated from the composite signal.
A video sync separator circuit, such as the National
Semiconductor LM1881, can be used for this purpose.
The clock feedback divider shown in Figure 1 is a digital
divider used within the PLL to multiply the reference
frequency. Its divide ratio establishes how many video dot
clock cycles occur per h-sync pulse. For example, if 880
pixel clocks are desired per h-sync pulse, then the divider
ratio is set to 880. Hence, together the h-sync frequency and
external divider ratio establish the dot clock frequency:
fOUT = fIN x N where N is external divide ratio
Both input pins IN and FBIN respond only to negative-going
clock edges of the input signal. The H-SYNC signal must be
constant frequency in the 12 kHz to 1 MHz range and stable
(low clock jitter) for creation of a stable output clock.
The output hook-ups of the IDT9173B are dictated by the
desired dot clock frequency. The primary consideration is
the internal VCO which operates over a frequency range of
10 MHz to 75 MHz. Because of the selectable VCO output
divider and the additional divider on output CLK2, four
distinct output frequency ranges can be achieved. The
following Table lists these ranges and the corresponding
device configuration.
Note that both outputs, CLK1 and CLK2, are available
during operation even though only one is fed back via the
external clock divider.
Pin 5, OE, tristates both CLK1 and CLK2 upon logic low
input. This feature can be used to revert dot clock control to
the system clock when not in genlock mode (hence, when in
genlock mode the system dot clock must be tristated).
When unused, inputs FS0 and OE must be tied to either
GND (logic low) or VDD (logic high).
Figure 1: Typical Application of IDT9173B in a Video Genlock System
FS0
State
Output
Used
Frequency/Range
IDT9173B-01
Frequency/Range
IDT9173B-15
0
CLK1
10 to 75 MHz
5 to 37.5 MHz
0
CLK2
5 to 37.5 MHz
2.5 to 18.75 MHz
1
CLK1
2.5 to 18.75 MHz
1.25 to 9.375 MHz
1
CLK2
1.25 to 9.375 MHz
0.625 to 4.6875 MHz
相关PDF资料 |
PDF描述 |
|---|---|
| 951601AFLFT | 66.66 MHz, PROC SPECIFIC CLOCK GENERATOR, PDSO48 |
| 954201BFLFT | 400 MHz, PROC SPECIFIC CLOCK GENERATOR, PDSO56 |
| 935271490512 | 4 CHANNEL(S), 5M bps, SERIAL COMM CONTROLLER, PQCC68 |
| 935271979118 | 8 I/O, PIA-GENERAL PURPOSE, PQCC16 |
| 935263358512 | 8-BIT, OTPROM, 20 MHz, MICROCONTROLLER, PDSO20 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 9173-B-156 | 制造商:Hart Scientific / Fluke 功能描述:METROLOGY WELL, 700C, W/9173-INSB, 115V 制造商:DANAHER - FLUKE 功能描述:METROLOGY WELL, 700C, W/9173-INSB, 115V |
| 9173B-15CS08LF | 功能描述:时钟发生器及支持产品 VIDEO GENERATOR CLK RoHS:否 制造商:Silicon Labs 类型:Clock Generators 最大输入频率:14.318 MHz 最大输出频率:166 MHz 输出端数量:16 占空比 - 最大:55 % 工作电源电压:3.3 V 工作电源电流:1 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:QFN-56 |
| 9173B-15CS08LFT | 功能描述:时钟发生器及支持产品 VIDEO GENERATOR CLK RoHS:否 制造商:Silicon Labs 类型:Clock Generators 最大输入频率:14.318 MHz 最大输出频率:166 MHz 输出端数量:16 占空比 - 最大:55 % 工作电源电压:3.3 V 工作电源电流:1 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:QFN-56 |
| 9173-B-R-156 | 制造商:Hart Scientific / Fluke 功能描述:METROLOGY WELL, 700C,W/9173-INSB,W/REF, 115V 制造商:DANAHER - FLUKE 功能描述:METROLOGY WELL, 700C,W/9173-INSB,W/REF, 115V 制造商:Fluke Electronics 功能描述:METROLOGY WELL, 700C,W/9173-INSB,W/REF, 115V |
| 9173C JB | 制造商:JET TEC 功能描述:CARTRIDGE EPSON COMP T033240+30% |
发布紧急采购，3分钟左右您将得到回复。