- 您现在的位置：买卖IC网 > PDF目录24619 > 9179BF-01LF (INTEGRATED DEVICE TECHNOLOGY INC) 91 SERIES, LOW SKEW CLOCK DRIVER, 18 TRUE OUTPUT(S), 0 INVERTED OUTPUT(S), PDSO48 PDF资料下载
参数资料
| 型号： | 9179BF-01LF |
| 厂商： | INTEGRATED DEVICE TECHNOLOGY INC |
| 元件分类： | 时钟及定时 |
| 英文描述： | 91 SERIES, LOW SKEW CLOCK DRIVER, 18 TRUE OUTPUT(S), 0 INVERTED OUTPUT(S), PDSO48 |
| 封装： | SSOP-48 |
| 文件页数： | 5/10页 |
| 文件大小： | 176K |
| 代理商： | 9179BF-01LF |
4
ICS9179B-01
Serial Configuration Command Bitmaps
Byte 0: SDRAM Clock Register
A.
For the clock generator to be addressed by an I
2C controller, the following address must be sent as a start
sequence, with an acknowledge bit between each byte.
B.
The clock generator is a slave/receiver I
2C component. It can "read back "(in Philips I2C protocol) the data stored
in the latches for verification. (set R/W# to 1 above). There is no BYTE count supported, so it does not meet
the Intel SMB PIIX4 protocol.
C.
The data transfer rate supported by this clock generator is 100K bits/sec (standard mode)
D.
The input is operating at 3.3V logic levels.
E.
The data byte format is 8 bit bytes.
F.
To simplify the clock generator I
2C interface, the protocol is set to use only block writes from the controller.The
bytes must be accessed in sequential order from lowest to highest byte with the ability to stop after any complete
byte has been transferred. The Command code and Byte count shown above must be sent, but the data is ignored
for those two bytes. The data is loaded until a Stop sequence is issued.
G.
In the power down mode (PWR_DWN# Low), the SDATA and SCLK pins are tristated and the internal data latches
maintain all prior programming information.
H.
At power-on, all registers are set to a default condition. Bytes 0 through 2 default to a 1 (Enabled output state).
General I
2C serial interface information
Notes: 1 = Enabled; 0 = Disabled, outputs held low
Then Byte 0, 1, 2, etc in
sequence until STOP.
Byte 0, 1, 2, etc in sequence until STOP.
Note: PWD = Power-Up Default
相关PDF资料 |
PDF描述 |
|---|---|
| 9179BF-01T | 9179 SERIES, LOW SKEW CLOCK DRIVER, 18 TRUE OUTPUT(S), 0 INVERTED OUTPUT(S), PDSO48 |
| 9179BF-01LFT | 9179 SERIES, LOW SKEW CLOCK DRIVER, 18 TRUE OUTPUT(S), 0 INVERTED OUTPUT(S), PDSO48 |
| 9179BF-01 | 9179 SERIES, LOW SKEW CLOCK DRIVER, 18 TRUE OUTPUT(S), 0 INVERTED OUTPUT(S), PDSO48 |
| 9179BF-03LF-T | 9179 SERIES, LOW SKEW CLOCK DRIVER, 10 TRUE OUTPUT(S), 0 INVERTED OUTPUT(S), PDSO28 |
| 9179BF-03LF | 9179 SERIES, LOW SKEW CLOCK DRIVER, 10 TRUE OUTPUT(S), 0 INVERTED OUTPUT(S), PDSO28 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 9179BF-01LFT | 功能描述:Clock Fanout Buffer (Distribution) IC 150MHz 48-BSSOP (0.295", 7.50mm Width) 制造商:idt, integrated device technology inc 系列:- 包装:带卷（TR） 零件状态:过期 类型:扇出缓冲器（分配） 电路数:1 比率 - 输入:输出:1：18 差分 - 输入:输出:无/无 输入:时钟 输出:时钟 频率 - 最大值:150MHz 电压 - 电源:3.135 V ~ 3.465 V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:48-BSSOP（0.295"，7.50mm 宽） 供应商器件封装:48-SSOP 标准包装:1,000 |
| 9179BF-03LF | 功能描述:时钟驱动器及分配 RoHS:否 制造商:Micrel 乘法/除法因子:1:4 输出类型:Differential 最大输出频率:4.2 GHz 电源电压-最大: 电源电压-最小:5 V 最大工作温度:+ 85 C 封装 / 箱体:SOIC-8 封装:Reel |
| 9179BF-03LFT | 功能描述:时钟驱动器及分配 RoHS:否 制造商:Micrel 乘法/除法因子:1:4 输出类型:Differential 最大输出频率:4.2 GHz 电源电压-最大: 电源电压-最小:5 V 最大工作温度:+ 85 C 封装 / 箱体:SOIC-8 封装:Reel |
| 917A524 | 功能描述:RF 连接器 SMA FEMALE PNL MNT 4 HOLE FLANGE RoHS:否 制造商:Bomar Interconnect 产品:Connectors 射频系列:BNC 型式:Jack (Female) 极性: 触点电镀:Gold 阻抗: 端接类型:Solder 主体类型:Straight Bulkhead 电缆类型: |
| 917A524B | 功能描述:RF 连接器 SMA PNL MNT JACK 4 HOLE BLUNT POST RoHS:否 制造商:Bomar Interconnect 产品:Connectors 射频系列:BNC 型式:Jack (Female) 极性: 触点电镀:Gold 阻抗: 端接类型:Solder 主体类型:Straight Bulkhead 电缆类型: |
发布紧急采购，3分钟左右您将得到回复。