- 您现在的位置：买卖IC网 > PDF目录18515 > 91904-3 (TE Connectivity)TOOL DIE SET SDE PREMIUM RG-55 PDF资料下载
参数资料
| 型号： | 91904-3 |
| 厂商： | TE Connectivity |
| 文件页数： | 1/5页 |
| 文件大小： | 0K |
| 描述： | TOOL DIE SET SDE PREMIUM RG-55 |
| 标准包装： | 5 |
| 系列： | Coaxicon |
| 压接或电缆尺寸： | RG/U-55 |
| 压接手柄： | A9996-ND |
| 连接器类型： | 同轴连接器 |
| 相关产品： | A9996-ND - PRO CRIMPER HAND TOOL W/O DIES |
| 其它名称： | A31206 |
SDE Crimping Die Assemblies
91900-1, 91901-1, 91903-1,
91904-[ ], and 91905-1
Instruction Sheet
408-8579
10 MAR 11 Rev C
PROPER USE GUIDELINES
Cumulative Trauma Disorders can result from the prolonged use of manually powered hand tools. Hand tools are intended for occasional use
and low volume applications. A wide selection of powered application equipment for extended-use, production operations is available.
Indenter
Die
Typical
Crimpiing
Die Assembly
Ferrule
Crimping
Chamber
coaxial cable. Each die is held in the PRO-CRIMPER
III hand tool jaws by a single screw. See Figure 1.
3. DIE INSTALLATION (Figure 1)
1. Close the tool handles until the ratchet releases,
then allow the tool handles to open fully.
2. Install anvil die in the movable jaw of the tool
frame. Align the die with the retaining screw hole,
then secure die with the die-retaining screw. Do
NOT fully tighten.
3. Install indenter die in the stationary jaw of the tool
frame. Slowly close the tool handles, allowing the
dies to align themselves.
Anvil Die
Center Contact
Crimping Chamber
NOTE
i
Once the anvil has entered the indenter, place a
copper bus bar (1.57 ± 0.05 [.062 ± .002] diameter)
into the center contact crimping chamber of the die
assembly.
Figure 1
1. INTRODUCTION
SDE (Two-Piece) Crimping Die Assemblies are
designed to crimp a variety of connectors when used
in PRO-CRIMPER* III Frame Assembly 354940-1.
Refer to Figure 5 for a list of connectors and their
associated dies.
4. Close the tool handles completely.
5. Securely tighten both screws with the appropriate
screwdriver.
4. CRIMPING PROCEDURE
Select the appropriate cable size and connector. The
wire size and insulation diameter must be within the
specified range for the connector.
Catalog 1307191 provides a guide for cable-to-
connector selection. For connectors not referenced in
the catalog, contact Tyco Electronics Product
Engineering for recommendations.
NOTE
i
This tool is provided with a crimp height adjustment
feature. Initially, the crimp height should be verified.
Refer to Section 5, Crimp height Adjustment, to
verify crimp height before using the tool.
NOTE
i
NOTE
Refer to instruction sheet 408-9930 for information
concerning PRO-CRIMPER II Hand Tool Frame
354940-1.
Dimensions in this instruction sheet are in
millimeters [with inches in brackets]. Figures are for
reference only, and are not drawn to scale.
Reasons for reissue of this instruction sheet are
provided in Section 8, REVISION SUMMARY.
2. DESCRIPTION
Each two-piece crimping die assembly consists of an
indenter die and an anvil die, which when closed forms
two or three crimping chambers. The larger crimping
chambers crimp the ferrule of the connector onto the
coaxial cable. The smaller crimping chamber crimps
the center contact onto the center conductor of the
For detailed information on cable strip lengths and
proper assembly of the connector, refer to the
instructions packaged with the connector. Make sure
that the connector's ferrule has been placed onto the
cable, and that the cable's braided shield is flared
away from the cable. Then proceed as follows:
4.1. Crimping the Center Contact (Figure 2)
1. Close the tool handles until the dies are partially
closed.
2. Assemble the center contact onto the cable
center conductor and place the center contact in the
smallest crimping chamber of the anvil die.
Make sure the flange on the end of the center
contact butts against the die.
i
?2011 Tyco Electronics Corporation, a TE Connectivity Ltd. Company
All Rights Reserved
TOOLING ASSISTANCE CENTER 1-800-722-1111
PRODUCT INFORMATION 1-800-522-6752
This controlled document is subject to change.
For latest revision and Regional Customer Service,
1 of 5
TE logo is a trademark.
*Trademark. Other products, logos, and company names might be trademarks of their respective owners.
visit our website at www.te.com
LOC B
相关PDF资料 |
PDF描述 |
|---|---|
| AML22CBJ8AD | SWITCH PUSHBUTTON DPDT 3A 125V |
| ATS073A-E | CRYSTAL 7.3728 MHZ SERIES FUND |
| 1624207-1 | POT 22K OHM 0.4W 20% SIDE FLAT |
| B32529C6163J289 | FILM CAP 0.0160UF 5% 400V |
| AML22CBE3BD | SWITCH PUSHBUTTON DPDT 0.1A 125V |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 91904-4 | 功能描述:冲压机与冲模 PREM SDE DIE COAXICO RoHS:否 制造商:Souriau 大小: 产品:Dies 类型:Crimping 描述/功能: |
| 91905 | 制造商:STANCOR 功能描述:coil Relay 120 VAC SPDT |
| 91-905 | 制造商:STANCOR 功能描述:coil Relay 120 VAC SPDT 制造商:White-Rodgers 功能描述: |
| 9190-5 | 功能描述:螺丝和紧固件 BIND HD SCRW BLUE RoHS:否 制造商:Unspecified 产品: 类型:Washer 螺纹大小: 长度: 材料:Steel 电镀:Nickel 螺丝头: 螺丝类型: |
| 919050-SE | 功能描述:液体分配器和瓶子 Epoxy Needle 19 GaugeX1/2" Black RoHS:否 制造商:OK International 产品:Soldering Tools 大小: 类型: 颜色: 特点: |
发布紧急采购，3分钟左右您将得到回复。