- 您现在的位置：买卖IC网 > PDF目录18519 > 91904-4 (TE Connectivity)TOOL DIE SET SDE PREMIUM RG-58 PDF资料下载
参数资料
| 型号： | 91904-4 |
| 厂商： | TE Connectivity |
| 文件页数： | 2/5页 |
| 文件大小： | 0K |
| 描述： | TOOL DIE SET SDE PREMIUM RG-58 |
| 标准包装： | 1 |
| 系列： | Coaxicon |
| 压接或电缆尺寸： | RG/U-58 |
| 压接手柄： | A9996-ND |
| 连接器类型： | 同轴连接器 |
| 产品目录页面： | 455 (CN2011-ZH PDF) |
| 相关产品： | A9996-ND - PRO CRIMPER HAND TOOL W/O DIES |
| 其它名称： | A31207 |
408-8579
Crimping the Center Contact
Typical Plug
Contact
Flange on End of
Contact
Crimping Die
Stripped
Cable
Typical Jack
Contact
Flange on End of
Contact
Anvil Die
Crimping Die
NOTE: Typical Crimping Dies Shown
Figure 2
crimp an improperly positioned ferrule.
NOTE
i
3. Holding the cable in place, close the tool handles
until the ratchet releases.
4. Allow the tool handles to open fully and remove
the crimped center contact from the dies.
4.2. Crimping the Ferrule (Figure 3)
1. Insert the crimped center contact into the
connector body until the cable dielectric butts
against the dielectric inside the connector body or
until the center contact is securely positioned within
the connector. Make sure that the braided shield is
over the support sleeve of the connector body and
that no strands from the shield enter the connector
body.
2. Slide the ferrule up over the braided shield and
onto the connector until the ferrule butts against the
shoulder on the connector body.
3. Place the ferrule in the appropriate crimping
chamber of the anvil die so that the shoulder on the
connector body butts against the edge of the die.
Refer to the instruction sheet packaged with the
connector to determine the appropriate crimping
chamber for the ferrule.
4. With a screwdriver, adjust the ratchet wheel from
the opposite side of the tool.
Rev C
CAUTION Make sure that both sides of the ferrule are started
evenly into the crimping chamber. Do not attempt to
!
5. Carefully close the tool handles until the ratchet
releases.
Crimping the Ferrule
Shoulder on
Connector Body
Butts Against
Edge of Die
Ferrule in Crimping
Chamber on Anvil
Die
NOTE: Typical Crimping Dies Shown
Figure 3
2 of 5
相关PDF资料 |
PDF描述 |
|---|---|
| 252B104A50TB | POT JOYSTICK 100K OHM W/SWITCH |
| B32520C6682K189 | FILM CAP 0.0068UF 10% 400V |
| 1624227-8 | POT 47K OHM 1/5W 20% SIDE ROUND |
| ASA2-72.000MHZ-L-T | OSC 72.000 MHZ 1.8V SMD |
| ASFLMPC-33.333MHZ-T3 | OSC 33.333 MHZ CMOS MEMS SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 91905 | 制造商:STANCOR 功能描述:coil Relay 120 VAC SPDT |
| 91-905 | 制造商:STANCOR 功能描述:coil Relay 120 VAC SPDT 制造商:White-Rodgers 功能描述: |
| 9190-5 | 功能描述:螺丝和紧固件 BIND HD SCRW BLUE RoHS:否 制造商:Unspecified 产品: 类型:Washer 螺纹大小: 长度: 材料:Steel 电镀:Nickel 螺丝头: 螺丝类型: |
| 919050-SE | 功能描述:液体分配器和瓶子 Epoxy Needle 19 GaugeX1/2" Black RoHS:否 制造商:OK International 产品:Soldering Tools 大小: 类型: 颜色: 特点: |
| 91905-1 | 功能描述:冲压机与冲模 PREM SDE DIE ARINC 3 CRIMP RoHS:否 制造商:Souriau 大小: 产品:Dies 类型:Crimping 描述/功能: |
发布紧急采购，3分钟左右您将得到回复。