- 您现在的位置：买卖IC网 > PDF目录24624 > 9250CF-10 (INTEGRATED DEVICE TECHNOLOGY INC) 100 MHz, PROC SPECIFIC CLOCK GENERATOR, PDSO56 PDF资料下载
参数资料
| 型号： | 9250CF-10 |
| 厂商： | INTEGRATED DEVICE TECHNOLOGY INC |
| 元件分类： | 时钟产生/分配 |
| 英文描述： | 100 MHz, PROC SPECIFIC CLOCK GENERATOR, PDSO56 |
| 封装： | 0.300 INCH, SSOP-56 |
| 文件页数： | 14/18页 |
| 文件大小： | 452K |
| 代理商： | 9250CF-10 |
5
ICS9250- 10
1.
The ICS clock generator is a slave/receiver, I2C component. It can read back the data stored in the latches for verification.
Read-BackwillsupportIntelPIIX4"Block-Read"protocol.
2.
The data transfer rate supported by this clock generator is 100K bits/sec or less (standard mode)
3.
The input is operating at 3.3V logic levels.
4.
The data byte format is 8 bit bytes.
5.
To simplify the clock generator I2C interface, the protocol is set to use only "Block-Writes" from the controller. The
bytes must be accessed in sequential order from lowest to highest byte with the ability to stop after any complete byte
has been transferred. The Command code and Byte count shown above must be sent, but the data is ignored for those
two bytes. The data is loaded until a Stop sequence is issued.
6.
At power-on, all registers are set to a default condition, as shown.
General I
2C serial interface information
The information in this section assumes familiarity with I2C programming.
For more information, contact ICS for an I2C programming application note.
How to Write:
Controller (host) sends a start bit.
Controller (host) sends the write address D2
(H)
ICS clock will acknowledge
Controller (host) sends a dummy command code
ICS clock will acknowledge
Controller (host) sends a dummy byte count
ICS clock will acknowledge
Controller (host) starts sending first byte (Byte 0)
through byte 5
ICS clock will acknowledge each byte one at a time.
Controller (host) sends a Stop bit
How to Read:
Controller (host) will send start bit.
Controler (host) sends the read address D3
(H)
ICS clock will acknowledge
ICS clock will send the byte count
Controller (host) acknowledges
ICS clock sends first byte (Byte 0) through byte 5
Controller (host) will need to acknowledge each byte
Controller (host) will send a stop bit
Notes:
Controller (Host)
ICS (Slave/Receiver)
Start Bit
Address
D3(H)
ACK
Byte Count
ACK
Byte 0
ACK
Byte 1
ACK
Byte 2
ACK
Byte 3
ACK
Byte 4
ACK
Byte 5
ACK
Stop Bit
How to Read:
Controller (Host)
ICS (Slave/Receiver)
Start Bit
Address
D2(H)
ACK
Dummy Command Code
ACK
Dummy Byte Count
ACK
Byte 0
ACK
Byte 1
ACK
Byte 2
ACK
Byte 3
ACK
Byte 4
ACK
Byte 5
ACK
Stop Bit
How to Write:
相关PDF资料 |
PDF描述 |
|---|---|
| 9250CF-10LF | 100 MHz, PROC SPECIFIC CLOCK GENERATOR, PDSO56 |
| 925387-1 | WIRE TERMINAL |
| 925387-2 | TAB TERMINAL |
| 925552-8 | 1 mm2, STEEL, NICKEL FINISH, WIRE TERMINAL |
| 925553-1 | 2.5 mm2, BRASS, WIRE TERMINAL |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 9250CF-10LF | 功能描述:时钟发生器及支持产品 RoHS:否 制造商:Silicon Labs 类型:Clock Generators 最大输入频率:14.318 MHz 最大输出频率:166 MHz 输出端数量:16 占空比 - 最大:55 % 工作电源电压:3.3 V 工作电源电流:1 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:QFN-56 |
| 9250CF-10LFT | 功能描述:时钟发生器及支持产品 RoHS:否 制造商:Silicon Labs 类型:Clock Generators 最大输入频率:14.318 MHz 最大输出频率:166 MHz 输出端数量:16 占空比 - 最大:55 % 工作电源电压:3.3 V 工作电源电流:1 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:QFN-56 |
| 9250YF-27LF-T | 制造商:IDT 制造商全称:Integrated Device Technology 功能描述:Frequency Generator and Integrated Buffers for Celeron & PII/IIITM |
| 9251 | 制造商:Apex Tool Group 功能描述:LOWER BRACKET FOR 9290 SERIES PNEUMATIC CUTTER |
| 9-251 | 制造商:Bernstein 功能描述:Bulk 制造商:BERNSTEIN WERKZEUGFABRIK 功能描述:VICE BALL SWIVEL MOUNTED 制造商:BERNSTEIN WERKZEUGFABRIK 功能描述:VICE, BALL SWIVEL MOUNTED 制造商:BERNSTEIN WERKZEUGFABRIK 功能描述:VICE, BALL SWIVEL MOUNTED; Accessory Type:Clamp Mounting Ball Joint Base; For Use With:Work Benches with Maximum Table Thickness of 80mm; SVHC:No SVHC (19-Dec-2012); Weight:950g ;RoHS Compliant: NA |
发布紧急采购，3分钟左右您将得到回复。