参数资料
型号: 92HD87B1X5NDGXYYX8
厂商: INTEGRATED DEVICE TECHNOLOGY INC
元件分类: 消费家电
英文描述: SPECIALTY CONSUMER CIRCUIT, QCC40
封装: ROHS COMPLIANT, QFN-40
文件页数: 57/204页
文件大小: 2369K
代理商: 92HD87B1X5NDGXYYX8
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页当前第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页第130页第131页第132页第133页第134页第135页第136页第137页第138页第139页第140页第141页第142页第143页第144页第145页第146页第147页第148页第149页第150页第151页第152页第153页第154页第155页第156页第157页第158页第159页第160页第161页第162页第163页第164页第165页第166页第167页第168页第169页第170页第171页第172页第173页第174页第175页第176页第177页第178页第179页第180页第181页第182页第183页第184页第185页第186页第187页第188页第189页第190页第191页第192页第193页第194页第195页第196页第197页第198页第199页第200页第201页第202页第203页第204页
IDT CONFIDENTIAL
15
V 0.995 01/11
2009 INTEGRATED DEVICE TECHNOLOGY, INC.
92HD87
SINGLE CHIP PC AUDIO SYSTEM, CODEC+STEREO SPEAKER AMPLIFIER+CAPLESS HP+LDO
enable this use model, the CODEC must resume within 10mS and not pop. Intel HDA015-B / Low
Power White paper power goals are < 30mW when analog PC_Beep is not enabled, and < 60mW
when analog PC_Beep is enabled. (Charge pump and BTL amplifier power excluded.)
While in AFG D3, the HD Audio controller may be in a D0 state (HD Audio bus active) or in a D3
state (HD Audio bus held in reset with no Bit_Clk, SData_Out, or Sync activity.) The expected behav-
ior is as follows (see the HDA015-B section for more information):
2.8.1.
AFG D3cold
The D3cold power state is the lowest power state available that does not use vendor specific verbs.
While in D3cold, the CODEC will still respond to bus requests to revert to a higher power state (dou-
ble AFG reset, link reset). However, audio processing, port presence detect, and other functions are
disabled. Per the HD Audio bus HDA015-B, the D3cold state is intended to be used just prior to
removing power to the CODEC. Typically, power will be removed within 200mS. However, the codec
may exit from the D3cold state by generating 2, back-to-back, AFG reset events. Resume time from
D3cold is less than 200mS.
2.9.
Vendor Specific Function Group Power States D4/D5
The codec introduces vendor specific power states. A vendor defined verb is added to the Audio
Function Group that combines multiple vendor specific power control bits into logical power states
for use by the audio driver. The 2 states defined offer lower power than the 5 existing states defined
in the HD Audio specification and HDA015-B. The Vendor Specific D4 state provides lower digital
power consumption relative to D3cold by disabling HD Audio link responses. Vendor specific D5 fur-
ther reduces power consumption on the digital supply by turning off GPIO drivers, and reduces ana-
log power consumption by turning off all analog circuitry except for reset circuits.
States D4/D5 are not entered until D3cold has been requested. Software can pre-program the D4 or
D5 state as a re-definition of how the part will behave when the D3cold power state is requested or
software may enter D3cold, then set the D4 or D5. The preferred method is to request D3cold, then
select D4 or D5 as desired.This will reduce the severity of pops encountered when entering D4 or
D5.
Both power states require a link reset or removal of DVDD to exit.
The CODEC may pop when using these verbs and transition times to an active state (D1 or D0 for
example) may take several seconds.
2.10. Low-voltage HDA Signaling
The codec is compatible with either 1.5V or 3.3V HDA bus signaling; the voltage selection is done
dynamically based on the input voltage of DVDD_IO.
DVDD_IO is currently not a logic configuration pin, but rather provides the digital power supply to be
used for the HDA bus signals.
Function
HDA Bus active
HDA Bus stopped
Port Presence Detect
state change
Unsolicited Response
Wake Event1 followed by an unsolicited response
1.The Port Presence detect circuit is currently dependent on a clock and must be changed to gener-
ate a wake event.
GPIO state change
Unsolicited Response
Wake Event followed by an unsolicited response
相关PDF资料
PDF描述
92HD87B1X5NDGXYYX SPECIALTY CONSUMER CIRCUIT, QCC40
92HD87B2X5NDGXYYX8 SPECIALTY CONSUMER CIRCUIT, QCC40
92HD87B2X5NDGXYYX SPECIALTY CONSUMER CIRCUIT, QCC40
92HD87B3X5NDGXYYX8 SPECIALTY CONSUMER CIRCUIT, QCC40
92HD87B3X5NDGXYYX SPECIALTY CONSUMER CIRCUIT, QCC40
相关代理商/技术参数
参数描述
92HD87B2X5NDGXRAX 功能描述:接口—CODEC RoHS:否 制造商:Texas Instruments 类型: 分辨率: 转换速率:48 kSPs 接口类型:I2C ADC 数量:2 DAC 数量:4 工作电源电压:1.8 V, 2.1 V, 2.3 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:DSBGA-81 封装:Reel
92HD87B2X5NDGXRAX8 功能描述:接口—CODEC RoHS:否 制造商:Texas Instruments 类型: 分辨率: 转换速率:48 kSPs 接口类型:I2C ADC 数量:2 DAC 数量:4 工作电源电压:1.8 V, 2.1 V, 2.3 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:DSBGA-81 封装:Reel
92HD87B3X5NDGXRAX 功能描述:接口—CODEC RoHS:否 制造商:Texas Instruments 类型: 分辨率: 转换速率:48 kSPs 接口类型:I2C ADC 数量:2 DAC 数量:4 工作电源电压:1.8 V, 2.1 V, 2.3 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:DSBGA-81 封装:Reel
92HD87B3X5NDGXRAX8 制造商:Integrated Device Technology Inc 功能描述:Audio Codec 2ADC / 2DAC 24-Bit 40-Pin QFN EP T/R 制造商:Integrated Device Technology Inc 功能描述:40QFN - Tape and Reel
92HD87B4X5NDGXRAX 功能描述:接口—CODEC RoHS:否 制造商:Texas Instruments 类型: 分辨率: 转换速率:48 kSPs 接口类型:I2C ADC 数量:2 DAC 数量:4 工作电源电压:1.8 V, 2.1 V, 2.3 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:DSBGA-81 封装:Reel