- 您现在的位置：买卖IC网 > PDF目录24830 > 935269823118 (NXP SEMICONDUCTORS) LINE TRANSCEIVER, PBCC16 PDF资料下载
参数资料
| 型号： | 935269823118 |
| 厂商： | NXP SEMICONDUCTORS |
| 元件分类： | Buffer和线驱动 |
| 英文描述： | LINE TRANSCEIVER, PBCC16 |
| 封装： | 3 X 3 X 0.65 MM, PLASTIC, MO-217, SOT-639-2, HBCC-16 |
| 文件页数： | 13/25页 |
| 文件大小： | 594K |
| 代理商： | 935269823118 |
Philips Semiconductors
ISP1105/1106/1107
Advanced USB transceivers
Product data
Rev. 07 — 29 March 2002
20 of 25
9397 750 09529
Koninklijke Philips Electronics N.V. 2002. All rights reserved.
15. Soldering
15.1 Introduction to soldering surface mount packages
This text gives a very brief insight to a complex technology. A more in-depth account
of soldering ICs can be found in our
Data Handbook IC26; Integrated Circuit
Packages (document order number 9398 652 90011).
There is no soldering method that is ideal for all surface mount IC packages. Wave
soldering can still be used for certain surface mount ICs, but it is not suitable for ne
pitch SMDs. In these situations reow soldering is recommended.
15.2 Reow soldering
Reow soldering requires solder paste (a suspension of ne solder particles, ux and
binding agent) to be applied to the printed-circuit board by screen printing, stencilling
or pressure-syringe dispensing before package placement.
Several methods exist for reowing; for example, convection or convection/infrared
heating in a conveyor type oven. Throughput times (preheating, soldering and
cooling) vary between 100 and 200 seconds depending on heating method.
Typical reow peak temperatures range from 215 to 250
°C. The top-surface
temperature of the packages should preferable be kept below 220
°C for thick/large
packages, and below 235
°C small/thin packages.
15.3 Wave soldering
Conventional single wave soldering is not recommended for surface mount devices
(SMDs) or printed-circuit boards with a high component density, as solder bridging
and non-wetting can present major problems.
To overcome these problems the double-wave soldering method was specically
developed.
If wave soldering is used the following conditions must be observed for optimal
results:
Use a double-wave soldering method comprising a turbulent wave with high
upward pressure followed by a smooth laminar wave.
For packages with leads on two sides and a pitch (e):
– larger than or equal to 1.27 mm, the footprint longitudinal axis is preferred to be
parallel to the transport direction of the printed-circuit board;
– smaller than 1.27 mm, the footprint longitudinal axis must be parallel to the
transport direction of the printed-circuit board.
The footprint must incorporate solder thieves at the downstream end.
For packages with leads on four sides, the footprint must be placed at a 45
° angle
to the transport direction of the printed-circuit board. The footprint must
incorporate solder thieves downstream and at the side corners.
相关PDF资料 |
PDF描述 |
|---|---|
| 0803-6204-02 | Quad ISDN U Interface Hybrid |
| 935269132112 | PLL BASED CLOCK DRIVER, 10 TRUE OUTPUT(S), 0 INVERTED OUTPUT(S), PDSO48 |
| 935270667118 | PLL BASED CLOCK DRIVER, 10 TRUE OUTPUT(S), 0 INVERTED OUTPUT(S), PDSO48 |
| 935269132118 | PLL BASED CLOCK DRIVER, 10 TRUE OUTPUT(S), 0 INVERTED OUTPUT(S), PDSO48 |
| 935269202112 | 8 I/O, PIA-GENERAL PURPOSE, PDSO16 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 935269987557 | 制造商:NXP Semiconductors 功能描述:SUB ONLY TDA9587-1US1-V1.8 SUBBED TO 935269987557 |
| 935270713557 | 制造商:NXP Semiconductors 功能描述:SUB ONLY IC CHP |
| 935270792551 | 制造商:NXP Semiconductors 功能描述:IC BUFF DVR TRI-ST 16BIT 56VFBGA |
| 935270792557 | 制造商:NXP Semiconductors 功能描述:IC BUFF DVR TRI-ST 16BIT 56VFBGA |
| 935270793551 | 制造商:NXP Semiconductors 功能描述:IC BUS TRCVR 3-ST 16BIT 56VFBGA |
发布紧急采购，3分钟左右您将得到回复。