- 您现在的位置：买卖IC网 > PDF目录42445 > 93C76A-E/MS 512 X 16 MICROWIRE BUS SERIAL EEPROM, PDSO8 PDF资料下载
参数资料
| 型号： | 93C76A-E/MS |
| 元件分类： | PROM |
| 英文描述： | 512 X 16 MICROWIRE BUS SERIAL EEPROM, PDSO8 |
| 封装： | ROHS COMPLIANT, PLASTIC, MSOP-8 |
| 文件页数： | 2/38页 |
| 文件大小： | 700K |
| 代理商： | 93C76A-E/MS |
第1页当前第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页
93XX46X/56X/66X/76X/86X
DS21929D-page 10
2007 Microchip Technology Inc.
3.0
FUNCTIONAL DESCRIPTION
When the ORG pin is connected to VCC, the (x16)
organization is selected. When it is connected to
ground, the (x8) organization is selected. Instruc-
tions, addresses and write data are clocked into the
DI pin on the rising edge of the clock (CLK). The DO
pin is normally held in a High-Z state except when
reading data from the device, or when checking the
Ready/Busy status during a programming operation.
The Ready/Busy status can be verified during an
Erase/Write operation by polling the DO pin; DO low
indicates that programming is still in progress, while
DO high indicates the device is ready. DO will enter
the High-Z state on the falling edge of CS.
3.1
Start Condition
The Start bit is detected by the device if CS and DI are
both high with respect to the positive edge of CLK for
the first time.
Before a Start condition is detected, CS, CLK and DI
may change in any combination (except to that of a
Start condition), without resulting in any device
operation (Read, Write, Erase, EWEN, EWDS, ERAL
or WRAL). As soon as CS is high, the device is no
longer in Standby mode.
An instruction following a Start condition will only be
executed if the required opcode, address and data bits
for any particular instruction are clocked in.
3.2
Data In/Data Out (DI/DO)
It is possible to connect the Data In and Data Out pins
together. However, with this configuration it is possible
for a “bus conflict” to occur during the “dummy zero”
that precedes the read operation, if A0 is a logic high
level. Under such a condition the voltage level seen at
Data Out is undefined and will depend upon the relative
impedances of Data Out and the signal source driving
A0. The higher the current sourcing capability of the
driver, the higher the voltage at the Data Out pin. In
order to limit this current, a resistor should be
connected between DI and DO.
3.3
Data Protection
All modes of operation are inhibited when VCC is below
a typical voltage of 1.5V for ‘93AAXX’ and ‘93LCXX’
devices or 3.8V for ‘93CXX’ devices.
The EWEN and EWDS commands give additional
protection against accidentally programming during
normal operation.
After power-up, the device is automatically in the
EWDS mode. Therefore, an EWEN instruction must be
performed before the initial ERASE or WRITE instruction
can be executed.
Block Diagram
Note:
When preparing to transmit an instruction,
either the CLK or DI signal levels must be
at a logic low as CS is toggled active high.
Note:
For added protection, an EWDS command
should be performed after every write
operation and an external 10 k
Ω pull-down
protection resistor should be added to the
CS pin.
Note:
To prevent accidental writes to the array in
the 93XX76C/86C devices, set the PE pin
to a logic low.
VCC
VSS
HV Generator
EEPROM
Array
I/O Control
Logic
Memory
Control
Logic
X
Dec
Byte Latches
Y Decoder
Sense Amp.
R/W Control
DI
DO
CS
CLK
ORG(1)
PE(2)
Note 1: ORG pin: Only on 93XX46C/56C/66C/76C/86C.
2: PE pin: Only on 93XX76C/86C.
相关PDF资料 |
PDF描述 |
|---|---|
| 93C76AT-E/ST | 256 X 16 MICROWIRE BUS SERIAL EEPROM, PDSO8 |
| 93AA76B-I/MC | 512 X 16 MICROWIRE BUS SERIAL EEPROM, PDSO8 |
| 93LC76AT-I/P | 128 X 8 MICROWIRE BUS SERIAL EEPROM, PDIP8 |
| 93C66BT-E/P | 128 X 8 MICROWIRE BUS SERIAL EEPROM, PDIP8 |
| 93AA56B-E/ST | 128 X 16 MICROWIRE BUS SERIAL EEPROM, PDSO8 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 93C76A-I/CH | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:1K-16K Microwire Compatible Serial EEPROMs |
| 93C76A-I/MC | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:1K-16K Microwire Compatible Serial EEPROMs |
| 93C76A-I/MCG | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:8K Microwire Compatible Serial EEPROM |
| 93C76AI/MS | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:8K Microwire Compatible Serial EEPROM |
| 93C76A-I/MS | 功能描述:电可擦除可编程只读存储器 8k 1024 X 8 SERIAL EE,IND RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 |
发布紧急采购，3分钟左右您将得到回复。