参数资料
| 型号： | 93LC76CT-I/ST |
| 厂商： | Microchip Technology |
| 文件页数： | 10/36页 |
| 文件大小： | 0K |
| 描述： | IC EEPROM 8KBIT 3MHZ 8TSSOP |
| 标准包装： | 2,500 |
| 格式 - 存储器： | EEPROMs - 串行 |
| 存储器类型： | EEPROM |
| 存储容量： | 8K（1K x 8 或 512 x 16） |
| 速度： | 2MHz，3MHz |
| 接口： | Microwire 3 线串行 |
| 电源电压： | 2.5 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 8-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 8-TSSOP |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页当前第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页
93AA76A/B/C, 93LC76A/B/C, 93C76A/B/C
3.0
PIN DESCRIPTIONS
TABLE 3-1:
PIN DESCRIPTIONS
Name
CS
CLK
DI
DO
V SS
ORG
PDIP
1
2
3
4
5
6
SOIC
1
2
3
4
5
6
TSSOP
1
2
3
4
5
6
MSOP
1
2
3
4
5
6
DFN (1)
1
2
3
4
5
6
TDFN (1)
1
2
3
4
5
6
SOT-23
5
4
3
1
2
—
Function
Chip Select
Serial Clock
Data In
Data Out
Ground
Organization/93XX76C
only
PE
7
7
7
7
7
7
—
Program Enable/
93XX76C only
V CC
8
8
8
8
8
8
6
Power Supply
Note 1:
The exposed pad on the DFN/TDFN package may be connected to V SS or left floating.
3.1
Chip Select (CS)
data bits before an instruction is executed. CLK and DI
A high level selects the device; a low level deselects
the device and forces it into Standby mode. However, a
then become “don’t care” inputs waiting for a new Start
condition to be detected.
programming cycle that is already in progress will be
completed, regardless of the Chip Select (CS) input
3.3
Data In (DI)
signal. If CS is brought low during a program cycle, the
device will go into Standby mode as soon as the
programming cycle is completed.
Data In (DI) is used to clock in a Start bit, opcode,
address and data synchronously with the CLK input.
CS must be low for 250 ns minimum (T CSL ) between
3.4
Data Out (DO)
consecutive instructions. If CS is low, the internal
control logic is held in a Reset status.
Data Out (DO) is used in the Read mode to output data
synchronously with the CLK input (T PD after the
3.2
Serial Clock (CLK)
positive edge of CLK).
This pin also provides Ready/ Busy status information
The Serial Clock is used to synchronize the communi-
cation between a master device and the 93XX series
device. Opcodes, address and data bits are clocked in
on the positive edge of CLK. Data bits are also clocked
out on the positive edge of CLK.
CLK can be stopped anywhere in the transmission
sequence (at high or low-level) and can be continued
anytime with respect to Clock High Time (T CKH ) and
Clock Low Time (T CKL ). This gives the controlling
master freedom in preparing opcode, address and
during erase and write cycles. Ready/ Busy status infor-
mation is available on the DO pin if CS is brought high
after being low for minimum Chip Select Low Time
(T CSL ) and an erase or write operation has been
initiated.
The Status signal is not available on DO, if CS is held
low during the entire erase or write cycle. In this case,
DO is in the High-Z mode. If status is checked after the
erase/write cycle, the data line will be high to indicate
the device is ready.
data.
CLK is a “don’t care” if CS is low (device deselected). If
CS is high, but the Start condition has not been
detected (DI = 0 ), any number of clock cycles can be
received by the device without changing its status (i.e.,
waiting for a Start condition).
Note:
3.5
After a programming cycle is complete,
issuing a Start bit and then taking CS low
will clear the Ready/ Busy status from DO.
Organization (ORG)
CLK cycles are not required during the self-timed write
(i.e., auto erase/write) cycle.
After detection of a Start condition the specified number
of clock cycles (respectively, low-to-high transitions of
CLK) must be provided. These clock cycles are
required to clock in all required opcode, address and
DS21796M-page 10
When the ORG pin is connected to V CC or logic high,
the (x16) memory organization is selected. When the
ORG pin is tied to V SS or logic low, the (x8) memory
organization is selected. For proper operation, ORG
must be tied to a valid logic level.
93XX76A devices are always (x8) organization and
93XX76B devices are always (x16) organization.
? 2003-2012 Microchip Technology Inc.
相关PDF资料 |
PDF描述 |
|---|---|
| EHHD15MM | CONN DSUB 15PIN MALE-MALE |
| ASM43DRST-S288 | CONN EDGECARD 86POS .156 EXTEND |
| 93LC76CT-I/MS | IC EEPROM 8KBIT 3MHZ 8MSOP |
| XC3S200A-5FG320C | IC SPARTAN-3A FPGA 200K 320FBGA |
| AGM43DRST-S288 | CONN EDGECARD EXTEND 86POS .156 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 93LC76-I/P | 功能描述:电可擦除可编程只读存储器 516x8 Or 1024x8 RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 |
| 93LC76-I/SN | 功能描述:电可擦除可编程只读存储器 516x8 Or 1024x8 RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 |
| 93LC76T/SN | 功能描述:电可擦除可编程只读存储器 516x8 Or 1024x8 RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 |
| 93LC76T-I/SN | 功能描述:电可擦除可编程只读存储器 516x8 Or 1024x8 RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 |
| 93LC86/P | 功能描述:电可擦除可编程只读存储器 1024x16-2048x8 PDIP8 RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 |
发布紧急采购，3分钟左右您将得到回复。