参数资料
| 型号： | 93LC86T/SN |
| 厂商： | Microchip Technology |
| 文件页数： | 6/22页 |
| 文件大小： | 0K |
| 描述： | IC EEPROM 16KBIT 3MHZ 8SOIC |
| 标准包装： | 3,300 |
| 格式 - 存储器： | EEPROMs - 串行 |
| 存储器类型： | EEPROM |
| 存储容量： | 16K（2K x 8 或 1K x 16） |
| 速度： | 2MHz，3MHz |
| 接口： | Microwire 3 线串行 |
| 电源电压： | 2.5 V ~ 6.0 V |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SOICN |
| 包装： | 带卷 (TR) |
93LC76/86
2.0
PRINCIPLES OF OPERATION
2.3
Erase/Write Enable and Disable
When the ORG pin is connected to V CC , the x16 orga-
nization is selected. When it is connected to ground,
the x8 organization is selected. Instructions, addresses
and write data are clocked into the DI pin on the rising
edge of the clock (CLK). The DO pin is normally held in
a high-Z state except when reading data from the
device, or when checking the Ready/Busy status
during a programming operation. The Ready/Busy
status can be verified during an erase/write operation
by polling the DO pin; DO low indicates that program-
ming is still in progress, while DO high indicates the
device is ready. The DO will enter the high-impedance
state on the falling edge of the CS.
(EWEN, EWDS)
The 93LC76/86 powers up in the Erase/Write Disable
(EWDS) state. All programming modes must be
preceded by an Erase/Write Enable ( EWEN ) instruction.
Once the EWEN instruction is executed, programming
remains enabled until an EWDS instruction is executed
or V CC is removed from the device. To protect against
accidental data disturb, the EWDS instruction can be
used to disable all erase/write functions and should
follow all programming operations. Execution of a READ
instruction is independent of both the EWEN and EWDS
instructions.
2.1
Start Condition
2.4 Data Protection
During power-up, all programming modes of operation
The Start bit is detected by the device if CS and DI are
both high with respect to the positive edge of CLK for
the first time.
Before a Start condition is detected, CS, CLK and DI
may change in any combination (except to that of a
Start condition), without resulting in any device opera-
tion (Read, Write, Erase, EWEN, EWDS, ERAL and
WRAL). As soon as CS is high, the device is no longer
in the Standby mode.
An instruction following a Start condition will only be
executed if the required amount of opcode, address
and data bits for any particular instruction are clocked
in.
After execution of an instruction (i.e., clock in or out of
the last required address or data bit) CLK and DI
become “don't care” bits until a new Start condition is
detected.
are inhibited until V CC has reached a level greater than
1.4V. During power-down, the source data protection
circuitry acts to inhibit all programming modes when
V CC has fallen below 1.4V.
The EWEN and EWDS commands give additional
protection against accidentally programming during
normal operation.
After power-up, the device is automatically in the
EWDS mode. Therefore, an EWEN instruction must be
performed before any ERASE or WRITE instruction can
be executed.
2.2
DI/DO
It is possible to connect the Data In and Data Out pins
together. However, with this configuration it is possible
for a “bus conflict” to occur during the “dummy zero”
that precedes the read operation, if A0 is a logic high
level. Under such a condition the voltage level seen at
Data Out is undefined and will depend upon the relative
impedances of Data Out and the signal source driving
A0. The higher the current sourcing capability of A0,
the higher the voltage at the Data Out pin.
DS21131F-page 6
? 2010 Microchip Technology Inc.
相关PDF资料 |
PDF描述 |
|---|---|
| 93LC86T-I/SN | IC EEPROM 16KBIT 3MHZ 8SOIC |
| 93LC76T/SN | IC EEPROM 8KBIT 3MHZ 8SOIC |
| XCV200E-6PQ240C | IC FPGA 1.8V C-TEMP 240-PQFP |
| 93LC76T-I/SN | IC EEPROM 8KBIT 3MHZ 8SOIC |
| XC6SLX100-3FG484I | IC FPGA SPARTAN 6 484FGGBGA |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 93LCL | 功能描述:SELF-LEVELING CROSS-LINE LASER L 制造商:klein tools, inc. 系列:- 零件状态:在售 工具类型:激光水准仪 配套使用产品/相关产品:测量 标准包装:1 |
| 93LCLS | 功能描述:SELF-LEVELING CROSS-LINE LASER L 制造商:klein tools, inc. 系列:- 零件状态:在售 工具类型:激光水准仪 配套使用产品/相关产品:测量 标准包装:1 |
| 93LCS56/66 WAF | 制造商:Microchip Technology Inc 功能描述: |
| 93LDM65 | 功能描述:LASER DISTANCE MEASURER 65 FT / 制造商:klein tools, inc. 系列:- 零件状态:在售 工具类型:测距仪，激光 配套使用产品/相关产品:现场测试 重量:0.253 磅（114.76g） 标准包装:1 |
| 93MT100K | 制造商:未知厂家 制造商全称:未知厂家 功能描述:THYRISTOR MODULE|3-PH FULL-WAVE|FULLY CNTLD|1KV V(RRM)|90A I(T) |
发布紧急采购，3分钟左右您将得到回复。