- 您现在的位置：买卖IC网 > PDF目录122717 > 951411BGLFT (INTEGRATED DEVICE TECHNOLOGY INC) 400 MHz, PROC SPECIFIC CLOCK GENERATOR, PDSO56 PDF资料下载
参数资料
| 型号： | 951411BGLFT |
| 厂商： | INTEGRATED DEVICE TECHNOLOGY INC |
| 元件分类： | 时钟产生/分配 |
| 英文描述： | 400 MHz, PROC SPECIFIC CLOCK GENERATOR, PDSO56 |
| 封装： | 6.10 MM, 0.50 MM PITCH, GREEN, MO-153, TSSOP-56 |
| 文件页数： | 9/21页 |
| 文件大小： | 225K |
| 代理商： | 951411BGLFT |
17
Integrated
Circuit
Systems, Inc.
ICS951411
0891E—03/07/05
Fig. 1
Shared Pin Operation -
Input/Output Pins
The I/O pins designated by (input/output) on the ICS951416
serve as dual signal functions to the device. During initial
power-up, they act as input pins. The logic level (voltage)
that is present on these pins at this time is read and stored
into a 5-bit internal data latch. At the end of Power-On reset,
(see AC characteristics for timing values), the device
changes the mode of operations for these pins to an output
function. In this mode the pins produce the specified buffered
clocks to external loads.
To program (load) the internal configuration register for
these pins, a resistor is connected to either the VDD (logic 1)
power supply or the GND (logic 0) voltage potential. A 10
Kilohm (10K) resistor is used to provide both the solid CMOS
programming voltage needed during the power-up
programming period and to provide an insignificant load on
the output clock during the subsequent operating period.
Via to
VDD
Clock trace to load
Series Term. Res.
Programming
Header
Via to Gnd
Device
Pad
2K
W
8.2K
W
Figure 1 shows a means of implementing this function
when a switch or 2 pin header is used. With no jumper is
installed the pin will be pulled high. With the jumper in
place the pin will be pulled low. If programmability is not
necessary, than only a single resistor is necessary. The
programming resistors should be located close to the series
termination resistor to minimize the current loop area. It is
more important to locate the series termination resistor
close to the driver than the programming resistor.
相关PDF资料 |
PDF描述 |
|---|---|
| 952302AG | PROC SPECIFIC CLOCK GENERATOR, PDSO48 |
| 9148F-18 | 100 MHz, PROC SPECIFIC CLOCK GENERATOR, PDSO28 |
| 932S203YGLFT | 133.3 MHz, PROC SPECIFIC CLOCK GENERATOR, PDSO56 |
| 9FG1200DG-1LFT | 400 MHz, OTHER CLOCK GENERATOR, PDSO56 |
| 935267488112 | 8-BIT, OTPROM, 20 MHz, MICROCONTROLLER, PDSO20 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 951412-2011309-AR-PT | 功能描述:集管和线壳 12P BD STCK HDR 2R STRT SMT 10U AU RoHS:否 产品种类:1.0MM Rectangular Connectors 产品类型:Headers - Pin Strip 系列:DF50 触点类型:Pin (Male) 节距:1 mm 位置/触点数量:16 排数:1 安装风格:SMD/SMT 安装角:Right 端接类型:Solder 外壳材料:Liquid Crystal Polymer (LCP) 触点材料:Brass 触点电镀:Gold 制造商:Hirose Connector |
| 951412-2011309-AR-TP | 功能描述:集管和线壳 12P BD STCK HDR 2R STRT SMT 10U AU RoHS:否 产品种类:1.0MM Rectangular Connectors 产品类型:Headers - Pin Strip 系列:DF50 触点类型:Pin (Male) 节距:1 mm 位置/触点数量:16 排数:1 安装风格:SMD/SMT 安装角:Right 端接类型:Solder 外壳材料:Liquid Crystal Polymer (LCP) 触点材料:Brass 触点电镀:Gold 制造商:Hirose Connector |
| 951412-2011409-AR-PT | 功能描述:集管和线壳 12P BD STCK HDR 2R STRT SMT 10U AU RoHS:否 产品种类:1.0MM Rectangular Connectors 产品类型:Headers - Pin Strip 系列:DF50 触点类型:Pin (Male) 节距:1 mm 位置/触点数量:16 排数:1 安装风格:SMD/SMT 安装角:Right 端接类型:Solder 外壳材料:Liquid Crystal Polymer (LCP) 触点材料:Brass 触点电镀:Gold 制造商:Hirose Connector |
| 951412-2011409-AR-TP | 功能描述:集管和线壳 12P BD STCK HDR 2R STRT SMT 10U AU RoHS:否 产品种类:1.0MM Rectangular Connectors 产品类型:Headers - Pin Strip 系列:DF50 触点类型:Pin (Male) 节距:1 mm 位置/触点数量:16 排数:1 安装风格:SMD/SMT 安装角:Right 端接类型:Solder 外壳材料:Liquid Crystal Polymer (LCP) 触点材料:Brass 触点电镀:Gold 制造商:Hirose Connector |
| 951412-2011609-AR-PT | 功能描述:集管和线壳 12P BD STCK HDR 2R STRT SMT 10U AU RoHS:否 产品种类:1.0MM Rectangular Connectors 产品类型:Headers - Pin Strip 系列:DF50 触点类型:Pin (Male) 节距:1 mm 位置/触点数量:16 排数:1 安装风格:SMD/SMT 安装角:Right 端接类型:Solder 外壳材料:Liquid Crystal Polymer (LCP) 触点材料:Brass 触点电镀:Gold 制造商:Hirose Connector |
发布紧急采购，3分钟左右您将得到回复。