- 您现在的位置：买卖IC网 > PDF目录8366 > 97-3057-1016-1 (Amphenol Industrial Operations)CABLE CLAMP+BUSHING 24,28 PDF资料下载
参数资料
| 型号： | 97-3057-1016-1 |
| 厂商： | Amphenol Industrial Operations |
| 文件页数： | 5/48页 |
| 文件大小： | 0K |
| 描述： | CABLE CLAMP+BUSHING 24,28 |
| 产品培训模块： | 97 Series MIL-5015 Connectors |
| 标准包装： | 1 |
| 系列： | 97 |
| 缆线开口： | 0.938"（23.80mm） |
| 外壳尺寸 - 插件： | 24，28 |
| 螺纹尺寸： | 1 7/16-18 |
| 特点： | 套管 |
| 产品目录页面： | 391 (CN2011-ZH PDF) |
| 配用： | 97-3106A-28-20P-ND - CONN PLUG 14POS STRAIGHT W/PIN 97-3106A-28-18P-ND - CONN PLUG 12POS STRAIGHT W/PIN 97-3106A-28-15S-ND - CONN PLUG 35POS STRAIGHT W/SKT 97-3106A-28-15P-ND - CONN PLUG 35POS STRAIGHT W/PIN 97-3106A-28-12S-ND - CONN PLUG 26POS STRAIGHT W/SKT 97-3106A-28-12P-ND - CONN PLUG 26POS STRAIGHT W/PIN 97-3106A-24-5S-ND - CONN PLUG 16POS STRAIGHT W/SKT 97-3106A-24-5P-ND - CONN PLUG 16POS STRAIGHT W/PIN 97-3106A-24-2P-ND - CONN PLUG 7POS STRAIGHT W/PIN 97-3106A-24-22S-ND - CONN PLUG 4POS STRAIGHT W/SKT 更多... |
| 相关产品： | 97-79-513-16-ND - BUSHING 24,28 15/16OD |
第1页第2页第3页第4页当前第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页
Guide to Selecting a Connector
1
2
3
4
5
6
7
8
In selecting a connector, it first must be
determined if a non-environmental 97
A or B Series 5015 type is required or if
an environmental MS-5015 Class E, F,
or R type* is required.
If determined that the general duty,
non-environmental 97 series is the
choice - then this catalog is appropriate
to your needs
The following 8 steps apply to for-
mulation of a part number.**
How many wires are you
going to connect?
What gauge?
These two questions are important,
because they indicate which insert you
need. There are literally hundreds to
choose from.
The insert arrangements for solder
contact connectors are illustrated on
pages 6-11. The inserts most often
used are highlighted on these pages.
Here’s an example of how to choose
an insert arrangement. Say you want to
connect eight 16-ga. wires, - first find
the section of arrangements contain-
ing 8 contacts. Insert number 20-7 is
the one you want because it contains
eight 16-ga. contacts and it is one of
the most often used. The one you
choose might depend on your space or
voltage requirements. The voltage
capacity of each insert is listed under
its diagram.
If you have more than one wire size
to connect, the method is essentially
the same. Actually, the insert configu-
rations for multiple-size wires are a lot
more flexible than they appear. That’s
because you can always solder a
smaller wire to a larger contact. How-
ever, soldering a large wire to a small
contact isn’t recommended because of
size and current requirements.
What if several identical
connectors have different
functions?
Here’s a situation to watch out for. You
have four identical receptacles on a
panel. One carries high current loads.
The others have low current functions.
A plug mated with the wrong receptacle
(cross-mating) could ruin your valu-
able equipment.
To avoid cross-mating, you can
order identical inserts positioned in
both the plugs and receptacles at vari-
ous angles from standard. These varia-
tions from standard position are called
alternate insert positions, and are
described on page 12.
What kind of receptacle do
you need?
For Wall Mounting Use a wall recep-
tacle, type 3100. The elongated back of
this receptacle extends through thick
wall material. It is threaded to accept
standard hardware fittings.
For Unmounted Applications Use
the cable receptacle, type 3101.
For Box or Panel Mounting Use the
box receptacle, type 3102. This recep-
tacle’s back is short to conserve space.
It is not threaded on the back end and
is used when no accessories such as
clamps are needed.
What kind of plug do you
need?
For ordinary situations The straight
plug, type 3106 meets most connector
requirements. However . . .
when space is critical you may want
to consider using an angle plug, type
3108. This type plug lets the cable
enter your equipment at a right angle.
Do you need a plug with a
Solid or Split back shell?
You can get both straight and angle
plugs in solid or split back shell
designs. With the solid shell you have
greater strength and you save space.
On the other hand, the split shell
design lets you quickly inspect the sol-
der terminals when you need to. This
feature could be important if you’ll be
subjecting the connector to rough han-
dling and heavy use.
The designation to use for solid
shell construction is the letter A. This
designation letter goes immediately
after the main shell type number: for
example, 3106A or 3108A.
The designation for split shell construc-
tion is the letter B; for example, 3106B
or 3108B.
Because of application, receptacles
are made in solid backshell construc-
tion only. Their designation is 3100A,
3101A. (See how to order for solder
contact connectors, page 19.
Which connector gets the
socket? - the receptacle or
the plug?
You’re at the point where you desig-
nate which inserts are used with which
shells. Either pin or socket inserts can
be used with plugs or receptacles.
Here’s a good rule of thumb. Order
the sockets for the connector at the
“hot” side of the circuit. By having sock-
ets at the power source, there’s little
chance that a wayward finger or screw-
driver will short the circuit or cause per-
sonal injury.
The designation for sockets is sim-
ply S in a part number, following the
insert code number. For pins, the des-
ignation is P. Therefore, the 20-7P
insert would have pin contacts, while
the 20-7S insert would have socket
contacts.
What type of plating is pre-
ferred?
If you prefer the standard olive cad-
mium, non-reflective, electrically con-
ductive finish, then no suffix number is
required. Other plating variations are
available, including environmentally
friendly zinc alloy. See how to order
instructions for the various plating fin-
ishes offered for 97 Series solder con-
nectors on page 19.
Do you need any
accessories?
Accessories - cable clamps, protection
caps and chains, conduit adapters, and
panel gaskets are shown on pages 33-
39.
* If an environmental type MIL-5015 E, F or R Class is required, then the
catalog that should be consulted is 12-020, MS/Standard MIL-5015
Cylindrical Connectors. See www.amphenol-industrial.com for on-line
catalogs or contact Amphenol, Sidney, NY.
** These steps are for solder type connectors which are described in
detail on pages 3-19. If a crimp type connector is needed, the same
steps apply, however, you should consult pages 20-29 for details on 97
Series connectors with crimp contacts.
相关PDF资料 |
PDF描述 |
|---|---|
| MS27508E16B6B | CONN HSG RCPT 6POS BOX MNT SCKT |
| MS27484T10F35PBLC | CONN HSG PLUG 13POS STRGHT PIN |
| 74HCT1G126GV,125 | IC BUS BUFF DVR TRI-ST SC74A |
| 97-3057-1008-1 | CABLE CLAMP+BUSHING 16,16S |
| MS27505E13B4SALC | CONN HSG RCPT 4POS BOX MNT SCKT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 97-3057-1016-1(621) | 功能描述:环形MIL规格应变消除装置与适配器 Clamp with Bushing Size 24, 28 Blk Zinc RoHS:否 制造商:Amphenol Industrial 产品:Cable Clamps 类型:Bushing Cable Clamps MIL 类型:MIL-DTL-5015 系列:97 外壳大小:16S, 16 匹配样式:Threaded 主体材料:Aluminum Alloy 主体类型:Straight |
| 97-3057-1016-1(639) | 功能描述:环形MIL规格应变消除装置与适配器 CLAMP CLEAR CHROMATE OVER CADMIUM RoHS:否 制造商:Amphenol Industrial 产品:Cable Clamps 类型:Bushing Cable Clamps MIL 类型:MIL-DTL-5015 系列:97 外壳大小:16S, 16 匹配样式:Threaded 主体材料:Aluminum Alloy 主体类型:Straight |
| 97-3057-1016-1(676) | 功能描述:环形MIL规格应变消除装置与适配器 CLAMP RoHS:否 制造商:Amphenol Industrial 产品:Cable Clamps 类型:Bushing Cable Clamps MIL 类型:MIL-DTL-5015 系列:97 外壳大小:16S, 16 匹配样式:Threaded 主体材料:Aluminum Alloy 主体类型:Straight |
| 97-3057-1016-1(689) | 功能描述:环形MIL规格应变消除装置与适配器 Cable Clamp with Bushing Sz 24/28 RoHS:否 制造商:Amphenol Industrial 产品:Cable Clamps 类型:Bushing Cable Clamps MIL 类型:MIL-DTL-5015 系列:97 外壳大小:16S, 16 匹配样式:Threaded 主体材料:Aluminum Alloy 主体类型:Straight |
| 97-3057-1016-1-621 | 制造商:Amphenol Corporation 功能描述:CLAMP - Bulk 制造商:Amphenol Industrial Operations 功能描述:CABLE CLAMP W/B 24 & 28 621 |
发布紧急采购，3分钟左右您将得到回复。