- 您现在的位置：买卖IC网 > PDF目录10195 > 97-3106A-24-28P (Amphenol Industrial Operations)CONN PLUG 24POS W/PINS PDF资料下载
参数资料
| 型号： | 97-3106A-24-28P |
| 厂商： | Amphenol Industrial Operations |
| 文件页数： | 5/48页 |
| 文件大小： | 0K |
| 描述： | CONN PLUG 24POS W/PINS |
| 产品培训模块： | 97 Series MIL-5015 Connectors |
| 产品目录绘图： | Insert Pattern 24-28 |
| 标准包装： | 1 |
| 系列： | 97 |
| 连接器类型： | 插头，公引脚 |
| 位置数： | 24 |
| 外壳尺寸 - 插件： | 24-28 |
| 安装类型： | 自由悬挂 |
| 端子： | 焊杯 |
| 紧固型： | 有螺纹 |
| 方向： | N（正常型） |
| 外壳材料，表面处理： | 铝，镀草绿色镉 |
| 触点表面涂层： | 银 |
| 包装： | 散装 |
| 额定电流： | 13A |
| 电压 - 额定： | 200VAC，250VDC |
| 工作温度： | -55°C ~ 125°C |
| 产品目录页面： | 391 (CN2011-ZH PDF) |
| 配套产品： | 97-3102A-24-28S-ND - CONN RECEPT BOX MNT 24POS W/SOCK |
| 相关产品： | 97-60-24P(621)-ND - CONN CAP FOR SIZE 24 PLUG 97-3057-1016-1-ND - CABLE CLAMP+BUSHING 24,28 97-3057-1016-ND - CABLE CLAMP 24,28 15/16OD |
| 其它名称： | 10-820073-28P |
第1页第2页第3页第4页当前第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页
Guide to Selecting a Connector
1
2
3
4
5
6
7
8
In selecting a connector, it first must be
determined if a non-environmental 97
A or B Series 5015 type is required or if
an environmental MS-5015 Class E, F,
or R type* is required.
If determined that the general duty,
non-environmental 97 series is the
choice - then this catalog is appropriate
to your needs
The following 8 steps apply to for-
mulation of a part number.**
How many wires are you
going to connect?
What gauge?
These two questions are important,
because they indicate which insert you
need. There are literally hundreds to
choose from.
The insert arrangements for solder
contact connectors are illustrated on
pages 6-11. The inserts most often
used are highlighted on these pages.
Here’s an example of how to choose
an insert arrangement. Say you want to
connect eight 16-ga. wires, - first find
the section of arrangements contain-
ing 8 contacts. Insert number 20-7 is
the one you want because it contains
eight 16-ga. contacts and it is one of
the most often used. The one you
choose might depend on your space or
voltage requirements. The voltage
capacity of each insert is listed under
its diagram.
If you have more than one wire size
to connect, the method is essentially
the same. Actually, the insert configu-
rations for multiple-size wires are a lot
more flexible than they appear. That’s
because you can always solder a
smaller wire to a larger contact. How-
ever, soldering a large wire to a small
contact isn’t recommended because of
size and current requirements.
What if several identical
connectors have different
functions?
Here’s a situation to watch out for. You
have four identical receptacles on a
panel. One carries high current loads.
The others have low current functions.
A plug mated with the wrong receptacle
(cross-mating) could ruin your valu-
able equipment.
To avoid cross-mating, you can
order identical inserts positioned in
both the plugs and receptacles at vari-
ous angles from standard. These varia-
tions from standard position are called
alternate insert positions, and are
described on page 12.
What kind of receptacle do
you need?
For Wall Mounting Use a wall recep-
tacle, type 3100. The elongated back of
this receptacle extends through thick
wall material. It is threaded to accept
standard hardware fittings.
For Unmounted Applications Use
the cable receptacle, type 3101.
For Box or Panel Mounting Use the
box receptacle, type 3102. This recep-
tacle’s back is short to conserve space.
It is not threaded on the back end and
is used when no accessories such as
clamps are needed.
What kind of plug do you
need?
For ordinary situations The straight
plug, type 3106 meets most connector
requirements. However . . .
when space is critical you may want
to consider using an angle plug, type
3108. This type plug lets the cable
enter your equipment at a right angle.
Do you need a plug with a
Solid or Split back shell?
You can get both straight and angle
plugs in solid or split back shell
designs. With the solid shell you have
greater strength and you save space.
On the other hand, the split shell
design lets you quickly inspect the sol-
der terminals when you need to. This
feature could be important if you’ll be
subjecting the connector to rough han-
dling and heavy use.
The designation to use for solid
shell construction is the letter A. This
designation letter goes immediately
after the main shell type number: for
example, 3106A or 3108A.
The designation for split shell construc-
tion is the letter B; for example, 3106B
or 3108B.
Because of application, receptacles
are made in solid backshell construc-
tion only. Their designation is 3100A,
3101A. (See how to order for solder
contact connectors, page 19.
Which connector gets the
socket? - the receptacle or
the plug?
You’re at the point where you desig-
nate which inserts are used with which
shells. Either pin or socket inserts can
be used with plugs or receptacles.
Here’s a good rule of thumb. Order
the sockets for the connector at the
“hot” side of the circuit. By having sock-
ets at the power source, there’s little
chance that a wayward finger or screw-
driver will short the circuit or cause per-
sonal injury.
The designation for sockets is sim-
ply S in a part number, following the
insert code number. For pins, the des-
ignation is P. Therefore, the 20-7P
insert would have pin contacts, while
the 20-7S insert would have socket
contacts.
What type of plating is pre-
ferred?
If you prefer the standard olive cad-
mium, non-reflective, electrically con-
ductive finish, then no suffix number is
required. Other plating variations are
available, including environmentally
friendly zinc alloy. See how to order
instructions for the various plating fin-
ishes offered for 97 Series solder con-
nectors on page 19.
Do you need any
accessories?
Accessories - cable clamps, protection
caps and chains, conduit adapters, and
panel gaskets are shown on pages 33-
39.
* If an environmental type MIL-5015 E, F or R Class is required, then the
catalog that should be consulted is 12-020, MS/Standard MIL-5015
Cylindrical Connectors. See www.amphenol-industrial.com for on-line
catalogs or contact Amphenol, Sidney, NY.
** These steps are for solder type connectors which are described in
detail on pages 3-19. If a crimp type connector is needed, the same
steps apply, however, you should consult pages 20-29 for details on 97
Series connectors with crimp contacts.
相关PDF资料 |
PDF描述 |
|---|---|
| LTC1279ISW#TR | IC ADC 12BIT SAMPL SHTDWN 24SOIC |
| VI-BW2-MY | CONVERTER MOD DC/DC 15V 50W |
| PX0745/P | CONN PLUG 7POS W/PINS BLACK |
| VI-BW1-MY | CONVERTER MOD DC/DC 12V 50W |
| D38999/20FB98PC | CONN RCPT 6POS WALL MNT W/PINS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 97-3106A24-28P | 制造商:Amphenol Corporation 功能描述:CIRCULAR SIZE 24 24WAY PIN 制造商:Amphenol Aerospace 功能描述:CIRCULAR, SIZE 24, 24WAY, PIN 制造商:Amphenol Industrial Operations 功能描述:CONNECTOR, CIRCULAR, PLUG, 24POS, CABLE; Connector Type:Circular Industrial; Series:97; Connector Body Material:Aluminium; Gender:Plug; Contact Gender:Pin; Connector Mounting:Cable; Connector Shell Size:24; Insert Arrangement:24-28 |
| 97-3106A-24-28P(426)(639) | 制造商:Amphenol Aerospace 功能描述:Conn MIL-C-5015 Circular PIN 24 POS Solder ST Cable Mount 24 Terminal 1 Port |
| 97-3106A-24-28P(621) | 功能描述:环形MIL规格连接器 24P Shell Size 24 Straight Plug RoHS:否 制造商:Amphenol MIL 类型:MIL-DTL-5015 系列:97 产品类型:Receptacles 外壳大小:28 外壳类型:Potting 触点类型:Socket (Female) 位置/触点数量:14 插入安排:28-2 触点材料:Copper Alloy 触点电镀:Silver 安装角:Straight 安装风格:Wire 端接类型:Solder 电流额定值: |
| 97-3106A-24-28P(639) | 功能描述:环形MIL规格连接器 24P Shell Size 24 Straight Plug RoHS:否 制造商:Amphenol MIL 类型:MIL-DTL-5015 系列:97 产品类型:Receptacles 外壳大小:28 外壳类型:Potting 触点类型:Socket (Female) 位置/触点数量:14 插入安排:28-2 触点材料:Copper Alloy 触点电镀:Silver 安装角:Straight 安装风格:Wire 端接类型:Solder 电流额定值: |
| 97-3106A-24-28P(689) | 功能描述:环形MIL规格连接器 24P SZ 24 Straight Solid Plug 5015 RoHS:否 制造商:Amphenol MIL 类型:MIL-DTL-5015 系列:97 产品类型:Receptacles 外壳大小:28 外壳类型:Potting 触点类型:Socket (Female) 位置/触点数量:14 插入安排:28-2 触点材料:Copper Alloy 触点电镀:Silver 安装角:Straight 安装风格:Wire 端接类型:Solder 电流额定值: |
发布紧急采购，3分钟左右您将得到回复。