- 您现在的位置：买卖IC网 > PDF目录25570 > 9P936AFLFT (INTEGRATED DEVICE TECHNOLOGY INC) LOW SKEW CLOCK DRIVER, PDSO28 PDF资料下载
参数资料
| 型号： | 9P936AFLFT |
| 厂商： | INTEGRATED DEVICE TECHNOLOGY INC |
| 元件分类： | 时钟及定时 |
| 英文描述： | LOW SKEW CLOCK DRIVER, PDSO28 |
| 封装： | ROHS COMPLIANT, MO-150, SSOP-28 |
| 文件页数： | 11/12页 |
| 文件大小： | 188K |
| 代理商： | 9P936AFLFT |
IDTTM/ICSTM
Low Skew Dual Bank DDR I/II Fan-out Buffer
1084C 12/03/09
ICS9P936
Low Skew Dual Bank DDR I/II Fan-out Buffer
8
1.
The ICS clock generator is a slave/receiver, I
2C component. It can read back the data stored in the latches for verification.
Read-Back will support Intel PIIX4 "Block-Read" protocol.
2.
The data transfer rate supported by this clock generator is 100K bits/sec or less (standard mode)
3.
The input is operating at 3.3V logic levels.
4.
The data byte format is 8 bit bytes.
5.
To simplify the clock generator I
2C interface, the protocol is set to use only "Block-Writes" from the controller. The bytes
must be accessed in sequential order from lowest to highest byte with the ability to stop after any complete byte has been
transferred. The Command code and Byte count shown above must be sent, but the data is ignored for those two bytes.
The data is loaded until a Stop sequence is issued.
6.
At power-on, all registers are set to a default condition, as shown.
Controller (Host)
ICS (Slave/Receiver)
Start Bit
Address
D4(H)
ACK
Dummy Command Code
ACK
Dummy Byte Count
ACK
Byte 0
ACK
Byte 1
ACK
Byte 2
ACK
Byte 3
ACK
Byte 4
ACK
Byte 5
ACK
Byte 6
ACK
Byte 7
ACK
Stop Bit
How to Write:
Controller (Host)
ICS (Slave/Receiver)
Start Bit
Address
D5(H)
ACK
Byte Count
ACK
Byte 0
ACK
Byte 1
ACK
Byte 2
ACK
Byte 3
ACK
Byte 4
ACK
Byte 5
ACK
Byte 6
ACK
Byte 7
Stop Bit
How to Read:
General I
2C serial interface information
The information in this section assumes familiarity with I
2C programming.
For more information, contact ICS for an I
2C programming application note.
How to Write:
Controller (host) sends a start bit.
Controller (host) sends the write address D4
(H)
ICS clock will
acknowledge
Controller (host) sends a dummy command code
ICS clock will
acknowledge
Controller (host) sends a dummy byte count
ICS clock will
acknowledge
Controller (host) starts sending first byte (Byte 0)
through byte 6
ICS clock will
acknowledge each byte one at a
time.
Controller (host) sends a Stop bit
How to Read:
Controller (host) will send start bit.
Controller (host) sends the read address D5
(H)
ICS clock will
acknowledge
ICS clock will send the
byte count
Controller (host) acknowledges
ICS clock sends first byte
(Byte 0) through byte
7
Controller (host) will need to acknowledge each
byte
Controller (host) will send a stop bit
Notes:
相关PDF资料 |
PDF描述 |
|---|---|
| 9UMS9001AKLFT | 200 MHz, PROC SPECIFIC CLOCK GENERATOR, PQCC56 |
| 9UMS9001AKLF | 200 MHz, PROC SPECIFIC CLOCK GENERATOR, PQCC56 |
| 9UMS9610CKLFT | 166.67 MHz, PROC SPECIFIC CLOCK GENERATOR, PQCC48 |
| 9UMS9610CKLF | 166.67 MHz, PROC SPECIFIC CLOCK GENERATOR, PQCC48 |
| 9UMS9633BFILFT | 166.67 MHz, PROC SPECIFIC CLOCK GENERATOR, PDSO48 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 9P936AGLF | 功能描述:时钟缓冲器 RoHS:否 制造商:Texas Instruments 输出端数量:5 最大输入频率:40 MHz 传播延迟（最大值）: 电源电压-最大:3.45 V 电源电压-最小:2.375 V 最大功率耗散: 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LLP-24 封装:Reel |
| 9P936AGLFT | 功能描述:时钟缓冲器 RoHS:否 制造商:Texas Instruments 输出端数量:5 最大输入频率:40 MHz 传播延迟（最大值）: 电源电压-最大:3.45 V 电源电压-最小:2.375 V 最大功率耗散: 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LLP-24 封装:Reel |
| 9P939AFLF | 制造商:Integrated Device Technology Inc 功能描述:IDT 9P939AFLF GENERAL PURPOSE SEMICONDUCTORS - Rail/Tube 制造商:Integrated Device Technology Inc 功能描述:IDT 9P939AFLF General Purpose Semiconductors |
| 9P946AFLF | 功能描述:时钟缓冲器 RoHS:否 制造商:Texas Instruments 输出端数量:5 最大输入频率:40 MHz 传播延迟（最大值）: 电源电压-最大:3.45 V 电源电压-最小:2.375 V 最大功率耗散: 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LLP-24 封装:Reel |
| 9P946AFLFT | 功能描述:时钟缓冲器 RoHS:否 制造商:Texas Instruments 输出端数量:5 最大输入频率:40 MHz 传播延迟（最大值）: 电源电压-最大:3.45 V 电源电压-最小:2.375 V 最大功率耗散: 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LLP-24 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。