- 您现在的位置：买卖IC网 > PDF目录15652 > A-SERIAL PROGRAMMING ADP (Fujitsu Semiconductor America Inc)SERIAL PROGRAM ADAPTER PDF资料下载
参数资料
| 型号： | A-SERIAL PROGRAMMING ADP |
| 厂商： | Fujitsu Semiconductor America Inc |
| 文件页数： | 7/14页 |
| 文件大小： | 0K |
| 描述： | SERIAL PROGRAM ADAPTER |
| 标准包装： | 1 |
| 模块/板类型： | 适配器板 |
| 适用于相关产品： | Fujitsu MCU |
| 其它名称： | 865-1113 A-SERIAL PROGRAMMING ADP-ND Q5749476 |
Procedure for Hardware/Software Setup of Flash Adapter
The following steps are required to set up the Hardware and software of the flash programming adapter.
1. Download the FLASH programming utility from the CD.
2. Connect one side of the ribbon cable to Adapter (J1) and other side to the user target board (Note: The user
board should have the 10-pin header for the cable). The pin outs for the header is shown in the figure 4, and
table1).
3. Connect '9 pin serial cable' or 'USB to serial cable' on one side to the adapter cable (J2) and other side to the
PC.
4. Set all DIP switches SW1 (MD0, MD2, Pxx, and Pyy) position to ON. Pxx aand Pyy pins are corresponds to
the pins listed in the Appendix A and B for starting pin for programming.
5. Connect the power supply to the target board (Power supply on the adapter board comes from the User
target Board via header).
6. Launch the flash programming utility on the PC.
7. Select the devices from the CPU list, and select the COM port (It depends on which port serial cable is
connected).
8. Switch on the power supply. Execute the < download> command from the Flash-programming interface.
9. If download is okay select the .mhx file (this file has been created after compiling the program) from the
user application software. Now select the <auto> command. A complete programming sequence will be
executed (Erase complete flash memory, blank check write file to flash memory and verify data). These
commands can be executed individually as well.
10. After successful execution of this command, set all the DIP switches to OFF, or disconnect the
programming cable.
11. The power on reset or pressing the reset button on target board will start the application in the flash
memory.
7
相关PDF资料 |
PDF描述 |
|---|---|
| VI-B0L-EY-F3 | CONVERTER MOD DC/DC 28V 50W |
| PA14SO1-03-6 | ADAPTER 14-SOIC TO 14-DIP |
| PA8SO1-03-6 | ADAPTER 8-SOIC TO 8-DIP |
| HSM11DRKI-S13 | CONN EDGECARD 22POS .156 EXTEND |
| PADSO2803Z-D420-28/2 | ADAPTER 28ZIF BD W/28SO PLUGS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ASERIES | 制造商:VISHAY 制造商全称:Vishay Siliconix 功能描述:Axial Leaded Multilayer Ceramic Capacitors for General Purpose Class 1, Class 2 and Class 3, 50 VDC, 100 VDC, 200 VDC, 500 VDC |
| ASESERIES | 制造商:ABRACON 制造商全称:Abracon Corporation 功能描述:3.3Vdc CMOS SMD CRYSTAL CLOCK OSCILLATOR |
| ASET | 制造商:ABRACON 制造商全称:Abracon Corporation 功能描述:TIGHT STABILITY INDUSTRIAL GRADE CRYSTAL OSCILLATOR |
| ASET_08 | 制造商:ABRACON 制造商全称:Abracon Corporation 功能描述:TIGHT STABILITY INDUSTRIAL GRADE CRYSTAL OSCILLATOR |
| ASET-10.000MHZ-Y-T | 功能描述:标准时钟振荡器 10MHz 3.0Volts 10ppm -40C +85C RoHS:否 制造商:AVX 产品:Standard Clock Oscillators 封装 / 箱体:7 mm x 5 mm 频率:75 MHz 频率稳定性:50 PPM 电源电压:2.5 V 负载电容: 端接类型:SMD/SMT 最小工作温度:0 C 最大工作温度:+ 70 C 输出格式:LVDS 尺寸: 封装:Reel 系列: |
发布紧急采购，3分钟左右您将得到回复。