参数资料
型号: A011-D-V-350
厂商: LEDdynamics Inc
文件页数: 4/9页
文件大小: 0K
描述: LED DRIVER 48V 350MA
标准包装: 10
系列: FlexBlock™ A011
类型: 恒定电流
拓扑: 降压-升压
输出数: 1
电压 - 输入(最小): 10V
电压 - 输入(最大): 32V
输出电压: 48V(最小值)
电流 - 输出(最大): 350mA
功率(瓦特): 17W
调光: 模拟,PWM
特点: SCP
工作温度: -40°C ~ 80°C
效率: 90%
端接类型: 导线引线
尺寸/尺寸: 2.00" L x 1.20" W x 0.38" H(50.8mm x 30.5mm x 9.5mm)
安装类型: 底座安装
其它名称: 788-1039
A011 FlexBlock
TM
High Output Wide Range LED Power Module
DATA SHEET Page 4 of 9
Specifications
Output current, A011-D-V-350 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 350mA
Output current, A011-D-V-700 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 700mA
Dimming Input, turn on threshold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.7V ±5%
Dimming Input, full on threshold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9V ±5%
External pot adjustment range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0%, 5-100% 4
Output rise time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . <2 ms 5, 6
Output fall time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . <100 μs 5, 6
Quiescent current (DIM = 0V) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . <6 mA 6
Operating temperature (Tcase). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -40-+80°C
Storage temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -40-+125°C
Application Information
The FlexBlock TM High Output LED Power Module is a high-efficiency dc to dc converter that delivers a fixed
output current by varying the output voltage as required to maintain the specified current. Because the
forward voltage of LEDs can change based on several environmental factors as well as the age of the LED, it
is important to use this type of driver in an LED system. A fast response current-sensing circuit permits the
unit to be used in applications where flashing or pulsing of the LEDs is required. Several options are available
allowing for use with many types of LEDs and in a variety of operating modes.
Fixed Current Drive
When the dimming wires (purple/gray) are left unconnected, the FlexBlock is designed to supply its rated
current to one or more LED junctions. For example, a 700mA rated unit will drive up to five white 700mA
LEDs connected in series at 12V DC . See figure 2 and figure 3.
When wired in the default configuration, as marked on the top of the unit, the A011 FlexBlock is in
Buck-Boost mode. This is the most flexible mode as it allows the input voltage to be below, the same, or
above the output voltage. This mode is recommended for loads with up to 6 LEDs in series.
A second, more efficient wiring option puts the A011 FlexBlock in boost-only mode. In this mode, the
LED+ output is not used, and the positive end of the LED load is instead connected to Vin+. This is shown in
Figure 11. It is extremely important that Vin < Vout under all conditions (LED forward voltages shrink slightly
as the LEDs warm up and as the LEDs are dimmed). If white LEDs are going to be dimmed, it is recommended
that Vin be less than (2V * #LEDs in series) to make sure the LEDs can be fully extinguished. This is due to the
fact that many LEDs will begin to light up at around 2.5V, at a reduced current, even when rated at 3.0Vf.
Figure 10 shows a 700mA unit driving multiple LEDs. Note that parallel strings of LEDs can be driven directly
with no additional circuitry required to insure current sharing. The nature of the LEDs themselves will provide
sufficient current sharing if the parallel strings comprise three or more junctions each, and are identical in length.
4 - Refer to figure 9 for the dimming response.
5 - Tested at 24V in , 24V out
6 - Actual value varies greatly based on input and/or output voltages. Actual values will be smaller in most applications.
?2011 LUXdrive, A Division of LEDdynamics, Inc. www.LUXdrive.com.
LEDdynamics, Inc.
Specifications subject to change without notice. May, 2011 - Rev 1.0
802.728.4533 P
802.728.3800 F
sales@LUXdrive.com
www.LUXdrive.com
Made in
the USA
相关PDF资料
PDF描述
S270J25SL0N6TJ5R CAP CER 27PF 1KV 5% RADIAL
EEC05DRTN-S734 CONN EDGECARD 10POS DIP .100 SLD
S220K25SL0N6TJ5R CAP CER 22PF 1KV 10% RADIAL
S220J25SL0N6TJ5R CAP CER 22PF 1KV 5% RADIAL
594D687X9004D2T035 CAP TANT 680UF 4V 10% 2917
相关代理商/技术参数
参数描述
A011-D-V-500 功能描述:LED SUPPLY CC FLEXBLOCK 500MA RoHS:是 类别:电源 - 外部/内部(非板载) >> LED 电源 - 恒定电压 系列:FlexBlock™ A011 标准包装:1 系列:LXV150 类型:恒定电压 拓扑:AC DC 转换器 输出数:1 电压 - 输入(最小):90VAC 电压 - 输入(最大):264VAC 输出电压:40V 电流 - 输出(最大):3.75A 功率(瓦特):150W 电压 - 隔离:3.75kV(3750V) 调光:- 特点:OCP,OTP,OVP,SCP 工作温度:-35°C ~ 70°C 效率:93% 端接类型:导线引线 尺寸/尺寸:8.90" L x 2.66" W x 1.57" H(226.0mm x 67.5mm x 40.0mm) 安装类型:底座安装 批准:CE,cULus,EN 额定值:IP67 重量:2.3 磅(1kg)
A011-D-V-700 功能描述:LED DRIVER 48V 700MA RoHS:是 类别:电源 - 外部/内部(非板载) >> LED 电源 - 恒定电压 系列:FlexBlock™ A011 标准包装:1 系列:LXV150 类型:恒定电压 拓扑:AC DC 转换器 输出数:1 电压 - 输入(最小):90VAC 电压 - 输入(最大):264VAC 输出电压:40V 电流 - 输出(最大):3.75A 功率(瓦特):150W 电压 - 隔离:3.75kV(3750V) 调光:- 特点:OCP,OTP,OVP,SCP 工作温度:-35°C ~ 70°C 效率:93% 端接类型:导线引线 尺寸/尺寸:8.90" L x 2.66" W x 1.57" H(226.0mm x 67.5mm x 40.0mm) 安装类型:底座安装 批准:CE,cULus,EN 额定值:IP67 重量:2.3 磅(1kg)
A012 功能描述:ADAPTER PROGRAMMER 16-SOIC RoHS:否 类别:编程器,开发系统 >> 过时/停产零件编号 系列:- 标准包装:1 系列:- 类型:MCU 适用于相关产品:Freescale MC68HC908LJ/LK(80-QFP ZIF 插口) 所含物品:面板、缆线、软件、数据表和用户手册 其它名称:520-1035
A012-006 功能描述:CABLE S-VIDEO 6' GOLD RoHS:是 类别:电缆组件 >> 圆形 系列:- 标准包装:1 系列:- 连接器类型:圆形 04 位置公型至导线引线 长度:1.64'(500.00mm) 缆线类型:单条 颜色:多色 屏蔽:无屏蔽 使用:面板安装,工业级 其它名称:SACC-E-MS-4CON-M16/0,5 SCO POSACC-E-MS-4CON-M16/0,5SCOPO
A01-200NS 制造商:未知厂家 制造商全称:未知厂家 功能描述:Logic IC