参数资料
型号: A011-D-V-700
厂商: LEDdynamics Inc
文件页数: 6/9页
文件大小: 0K
描述: LED DRIVER 48V 700MA
标准包装: 10
系列: FlexBlock™ A011
类型: 恒定电流
拓扑: 降压-升压
输出数: 1
电压 - 输入(最小): 10V
电压 - 输入(最大): 32V
输出电压: 48V(最小值)
电流 - 输出(最大): 700mA
功率(瓦特): 34W
调光: 模拟,PWM
特点: SCP
工作温度: -40°C ~ 80°C
效率: 90%
端接类型: 导线引线
尺寸/尺寸: 2.00" L x 1.20" W x 0.38" H(50.8mm x 30.5mm x 9.5mm)
安装类型: 底座安装
其它名称: 788-1038
A011 FlexBlock
TM
High Output Wide Range LED Power Module
DATA SHEET Page 6 of 9
External On/Off Control
Where a manual on/off control is desired, the potentiometer in Figure 14 may be replaced by a
pushbutton or toggle switch. The output current will be zero and the input current will drop to the
quiescent level when the switch is closed. Figures 16 and 17 show external dimming control combined
with on/off control.
Thermal Management
The FlexBlock can run many LED load configurations with no additional heat sinking in an ambient of
25 ° C. In situations with elevated ambient temperatures, such as those that might be experienced inside
an enclosed fixture, additional heat sinking may be required. If the temperature of the driver (as
measured at the T marking on the label) exceeds 60 ° C, additional heat sinking is recommended. If the
temperature of the driver exceeds 80 ° C, additional heat sinking is required.
The best surface for removing heat form the FlexBlock is the back side (opposite the labeled side). The
module can be attached to a heat sink with thermal grease and a mounting bracket that presses the unit
firmly against the heat sink, or with double-sided tape that provides both the thermal path and
mechanical mounting. When using tape (such as 3M F9469PC, a Very High Bond (VHB) tape suitable for
permanent mounting), using a thinner variety (0.005” thick or less) will aid in getting the heat through
the tape and to the heat sink. Care should be taken when positioning the FlexBlock module with VHB
tape as the high bond strength makes removing or repositioning the module very difficult.
If the FlexBlock becomes too hot during use, it will reduce the output current to limit the power
dissipation. If the temperature continues to rise, the driver will turn off until the temperature drops to a
safe level.
Connections
In all cases, the LEDs being driven should be located as close to the FlexBlock LED output as possible.
18AWG wire should be adequate for most wiring, but a heavier gauge should be considered when
long leads are required.
The power input wires should also be kept short. Where the power source is located several feet from the
unit, a 100μF or larger, 50V capacitor may be required across the input terminals as shown in Figure 20.
?2011 LUXdrive, A Division of LEDdynamics, Inc. www.LUXdrive.com.
LEDdynamics, Inc.
Specifications subject to change without notice. May, 2011 - Rev 1.0
802.728.4533 P
802.728.3800 F
sales@LUXdrive.com
www.LUXdrive.com
Made in
the USA
相关PDF资料
PDF描述
JTAGJET-TRACE-CM3-2 JTAG EMULATOR CORTEX-M3 2M MEM
S470K25SL0N6TJ5R CAP CER 47PF 1KV 10% RADIAL
T95Z106K035LSSL CAP TANT 10UF 35V 10% 2910
S470J25SL0N6TJ5R CAP CER 47PF 1KV 5% RADIAL
JTAGJET-ARM11 JTAG EMULATOR FOR ARM7/9/11
相关代理商/技术参数
参数描述
A012 功能描述:ADAPTER PROGRAMMER 16-SOIC RoHS:否 类别:编程器,开发系统 >> 过时/停产零件编号 系列:- 标准包装:1 系列:- 类型:MCU 适用于相关产品:Freescale MC68HC908LJ/LK(80-QFP ZIF 插口) 所含物品:面板、缆线、软件、数据表和用户手册 其它名称:520-1035
A012-006 功能描述:CABLE S-VIDEO 6' GOLD RoHS:是 类别:电缆组件 >> 圆形 系列:- 标准包装:1 系列:- 连接器类型:圆形 04 位置公型至导线引线 长度:1.64'(500.00mm) 缆线类型:单条 颜色:多色 屏蔽:无屏蔽 使用:面板安装,工业级 其它名称:SACC-E-MS-4CON-M16/0,5 SCO POSACC-E-MS-4CON-M16/0,5SCOPO
A01-200NS 制造商:未知厂家 制造商全称:未知厂家 功能描述:Logic IC
A0120106A 制造商:未知厂家 制造商全称:未知厂家 功能描述:MINIATURE WIDEBAND RF AMPLIFIERS
A012-012 功能描述:CABLE S-VIDEO M/M GOLD 12' RoHS:是 类别:电缆组件 >> 圆形 系列:- 标准包装:1 系列:- 连接器类型:圆形 04 位置公型至导线引线 长度:1.64'(500.00mm) 缆线类型:单条 颜色:多色 屏蔽:无屏蔽 使用:面板安装,工业级 其它名称:SACC-E-MS-4CON-M16/0,5 SCO POSACC-E-MS-4CON-M16/0,5SCOPO