- 您现在的位置：买卖IC网 > PDF目录21930 > A1202LUA-T (Allegro Microsystems Inc)IC SW CONTINUOUS TIME BIPO 3-SIP PDF资料下载
参数资料
| 型号： | A1202LUA-T |
| 厂商： | Allegro Microsystems Inc |
| 文件页数： | 11/14页 |
| 文件大小： | 356K |
| 描述： | IC SW CONTINUOUS TIME BIPO 3-SIP |
| 产品培训模块： | Current Sensor |
| 标准包装： | 4,000 |
| 传感范围： | 75G 跳闸，-75G 释放 |
| 类型： | 双极卡锁 |
| 电源电压： | 3.8 V ~ 24 V |
| 电流 - 电源： | 7.5mA |
| 电流 - 输出（最大）： | 25mA |
| 输出类型： | 数字式，开漏极 |
| 特点： | 稳压电压 |
| 工作温度： | -40°C ~ 150°C |
| 封装/外壳： | 3-SIP |
| 供应商设备封装： | 3-SIP |
| 包装： | 散装 |
| 其它名称： | 620-1010 |
Continuous-Time Bipolar Switch Family
A1202
and A1203
11
Allegro MicroSystems, LLC
115 Northeast Cutoff, Box 15036
Worcester, Massachusetts 01615-0036 (508) 853-5000
www.allegromicro.com
Power Derating
Power Derating
The device must be operated below the maximum junction
temperature of the device, T
J(max)
. Under certain combinations of
peak conditions, reliable operation may require derating sup-
plied power or improving the heat dissipation properties of the
application. This section presents a procedure for correlating
factors affecting operating T
J
. (Thermal data is also available on
the Allegro MicroSystems Web site.)
The Package Thermal Resistance, R
qJA
, is a figure of merit sum-
marizing the ability of the application and the device to dissipate
heat from the junction (die), through all paths to the ambient air.
Its primary component is the Effective Thermal Conductivity,
K, of the printed circuit board, including adjacent devices and
traces. Radiation from the die through the device case, R
qJC
, is
relatively small component of R
qJA
. Ambient air temperature,
T
A
, and air motion are significant external factors, damped by
overmolding.
The effect of varying power levels (Power Dissipation, P
D
), can
be estimated. The following formulas represent the fundamental
relationships used to estimate T
J
, at P
D
.
P
D
= V
IN
?/DIV>
I
IN
(1)
DT = P
D
?/DIV>
R
qJA
(2)
T
J
= T
A
+ 擳 (3)
For example, given common conditions such as: T
A
= 25癈,
V
CC
= 12 V, I
CC
= 4 mA, and R
qJA
= 140 癈/W, then:
P
D
= V
CC
?/DIV>
I
CC
= 12 V
?/DIV>
4 mA = 48 mW
DT = P
D
?/DIV>
R
qJA
= 48 mW
?/DIV>
140 癈/W = 7癈
T
J
= T
A
+ DT = 25癈 + 7癈 = 32癈
A worst-case estimate, P
D(max)
, represents the maximum allow-
able power level (V
CC(max)
, I
CC(max)
), without exceeding T
J(max)
,
at a selected R
qJA
and T
A
.
Example: Reliability for V
CC
at T
A
=
150癈, package UA, using
minimum-K PCB.
Observe the worst-case ratings for the device, specifically:
R
qJA
=
165癈/W, T
J(max)
=
165癈, V
CC(max)
=
24 V, and
I
CC(max)
=
7.5
mA.
Calculate the maximum allowable power level, P
D(max)
. First,
invert equation 3:
DT
max
= T
J(max)
T
A
= 165
癈
150
癈 = 15
癈
This provides the allowable increase to T
J
resulting from internal
power dissipation. Then, invert equation 2:
P
D(max)
= DT
max
?R
qJA
= 15癈 ?165 癈/W = 91 mW
Finally, invert equation 1 with respect to voltage:
V
CC(est)
= P
D(max)
? I
CC(max)
= 91 mW ?7.5 mA = 12.1 V
The result indicates that, at T
A
, the application and device can
dissipate adequate amounts of heat at voltages dV
CC(est)
.
Compare V
CC(est)
to V
CC(max)
. If V
CC(est)
d V
CC(max)
, then reli-
able operation between V
CC(est)
and V
CC(max)
requires enhanced
R
qJA
. If V
CC(est)
e V
CC(max)
, then operation between V
CC(est)
and
V
CC(max)
is reliable under these conditions.
相关PDF资料 |
PDF描述 |
|---|---|
| ABJ1614409 | SWITCH SNAP SPDT 1A SIM ROLLWIRE |
| A1103LUA-T | IC SWITCH HALL EFFECT 3-SIP |
| ABJ1612409 | SWITCH TURQ SPDT 1A HING WIRE LD |
| A1102LUA-T | IC SWITCH HALL EFFECT 3-SIP |
| A1214LUA-T | IC LATCH HALL EFFECT 3-SIP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| A1202P2 10 | 制造商:Thomas & Betts 功能描述:SS A1202P210 COMBO CHANNEL SIDE HOL |
| A1202W 20 | 制造商:Thomas & Betts 功能描述:A1200 BACK-TO-BACK WELDED |
| A1202W 20PG | 制造商:Thomas & Betts 功能描述:BACK-TO-BACK WELDED PRE-GALV STRUT |
| A1202W 27PG | 制造商:Thomas & Betts 功能描述:COMBINATION CHANNEL |
| A1203 | 制造商:Quick 功能描述:QFP 35 X 35NOZZLE FOR QUICK957/957D |
发布紧急采购，3分钟左右您将得到回复。