参数资料
型号: A1222LUA-T
厂商: Allegro Microsystems Inc
文件页数: 10/16页
文件大小: 347K
描述: IC HALL EFFECT LATCH 3-SIP
产品培训模块: Current Sensor
标准包装: 4,000
传感范围: 150G 跳闸,150G 释放
类型: 双极卡锁
电源电压: 3 V ~ 24 V
电流 - 电源: 4mA
电流 - 输出(最大): 25mA
输出类型: 数字式,开漏极
特点: 稳压电压
工作温度: -40°C ~ 150°C
封装/外壳: 3-SIP
供应商设备封装: 3-SIP
包装: 散装
其它名称: 620-1474
A1222LUA-T-ND
Chopper Stabilized Precision Hall Effect Latches
A1220, A1221,
A1222, and A1223
10
Allegro MicroSystems, LLC
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
C
BYP
A122x
VOUT
GND
0.1 糉
VCC
Output
R
L
V
S
Operation
The output of these devices switches low (turns on) when a mag-
netic field perpendicular to the Hall element exceeds the operate
point threshold, B
OP
 (see panel A of figure 1). After turn-on, the
output voltage is V
OUT(SAT)
. The output transistor is capable of
sinking current up to the short circuit current limit, I
OM
, which is
a minimum of 30 mA. When the magnetic field is reduced below
the release point, B
RP
 , the device output goes high (turns off).
The difference in the magnetic operate and release points is the
hysteresis, B
HYS ,
 of the device. This built-in hysteresis allows
clean switching of the output even in the presence of external
mechanical vibration and electrical noise.
Removal of the magnetic field will leave the device output
latched on if the last crossed switchpoint is B
OP
, or latched off if
the last crossed switch point is B
RP
.
Powering-on the device in the hysteresis range (less than B
OP
 and
higher than B
RP
) will give an indeterminate output state. The cor-
rect state is attained after the first excursion beyond B
OP
 or B
RP
.
Applications
It is strongly recommended that an external bypass capacitor be
connected (in close proximity to the Hall element) between the
supply and ground of the device to reduce both external noise
and noise generated by the chopper stabilization technique. As is
shown in panel B of figure 1, a 0.1 糉 capacitor is typical.
Extensive applications information for Hall effect devices is
available in:
" Hall-Effect IC Applications Guide, Application Note 27701
" Guidelines for Designing Subassemblies Using Hall-Effect 
Devices, Application Note 27703.1
" Soldering Methods for Allegros Products  SMT and Through-
Hole, Application Note 26009
All are provided in Allegro Electronic Data Book, AMS-702, and
the Allegro Web site, www.allegromicro.com.
Figure 1. Switching behavior of latches. In panel A, on the horizontal axis, the B+ direction indicates increasing south polarity magnetic field strength,
and the B direction indicates decreasing south polarity field strength (including the case of increasing north polarity). This behavior can be exhibited
when using a circuit such as that shown in panel B.
(A)
(B)
Functional Description
B
HYS
V
CC
V
OUT(SAT)
B+
B
V+
0
0
相关PDF资料
PDF描述
DST-5-12 XFRMR PWR 115/230V 6.3VAC 2.0A
9922-18YEL LEAD PLUG STK BAN 2MM YEL 18"
ST-5-20 XFRMR PWR 115V 10VAC 1.2A
DST-5-20 XFRMR PWR 115/230V 10VAC 1.2A
9922-18WTE LEAD PLUG STK BAN 2MM WHITE 18"
相关代理商/技术参数
参数描述
A1223 制造商:ALLEGRO 制造商全称:Allegro MicroSystems 功能描述:Chopper Stabilized Precision Hall Effect Latches
A-1223 制造商:TE Connectivity 功能描述:
A1223ELHLT-T 功能描述:SENSOR HALL EFF DGTL LATCH SOT23 RoHS:是 类别:传感器,转换器 >> 磁性 - 霍尔效应,数字式开关,线性,罗盘 (IC) 系列:- 标准包装:1 系列:- 传感范围:20mT ~ 80mT 类型:旋转 电源电压:4.5 V ~ 5.5 V 电流 - 电源:15mA 电流 - 输出(最大):- 输出类型:数字式,PWM,8.5 位串行 特点:可编程 工作温度:-40°C ~ 150°C 封装/外壳:20-SSOP(0.209",5.30mm 宽) 供应商设备封装:20-SSOP 包装:Digi-Reel® 其它名称:AS5132-HSST-500DKR
A1223ELHLX-T 功能描述:SENSOR HALL EFF DGTL LATCH SOT23 RoHS:是 类别:传感器,转换器 >> 磁性 - 霍尔效应,数字式开关,线性,罗盘 (IC) 系列:- 标准包装:1 系列:- 传感范围:20mT ~ 80mT 类型:旋转 电源电压:4.5 V ~ 5.5 V 电流 - 电源:15mA 电流 - 输出(最大):- 输出类型:数字式,PWM,8.5 位串行 特点:可编程 工作温度:-40°C ~ 150°C 封装/外壳:20-SSOP(0.209",5.30mm 宽) 供应商设备封装:20-SSOP 包装:Digi-Reel® 其它名称:AS5132-HSST-500DKR
A1223ELHLX-T2 制造商:ALLEGRO 制造商全称:Allegro MicroSystems 功能描述:Chopper Stabilized Precision Hall Effect Latches