- 您现在的位置：买卖IC网 > PDF目录67355 > A1244LLHLX-I1-T MAGNETIC FIELD SENSOR-HALL EFFECT, -8-8mT, RECTANGULAR, SURFACE MOUNT PDF资料下载
参数资料
| 型号： | A1244LLHLX-I1-T |
| 元件分类： | 磁阻传感器 |
| 英文描述： | MAGNETIC FIELD SENSOR-HALL EFFECT, -8-8mT, RECTANGULAR, SURFACE MOUNT |
| 封装： | 2 MM X 3 MM, 1 MM HEIGHT , LEAD FREE, SOT-23W, 3 PIN |
| 文件页数： | 12/12页 |
| 文件大小： | 251K |
| 代理商： | A1244LLHLX-I1-T |
Chopper-Stabilized, Two Wire
Hall-Effect Latch
A1244
9
Allegro MicroSystems, Inc.
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
Preliminary Data Sheet
Subject to Change Without Notice
May 5, 2011
The device must be operated below the maximum junction tem-
perature of the device, TJ(max). Under certain combinations of
peak conditions, reliable operation may require derating supplied
power or improving the heat dissipation properties of the appli-
cation. This section presents a procedure for correlating factors
affecting operating TJ. (Thermal data is also available on the
Allegro MicroSystems Web site.)
The Package Thermal Resistance, RJA, is a figure of merit sum-
marizing the ability of the application and the device to dissipate
heat from the junction (die), through all paths to the ambient air.
Its primary component is the Effective Thermal Conductivity, K,
of the printed circuit board, including adjacent devices and traces.
Radiation from the die through the device case, RJC, is relatively
small component of RJA. Ambient air temperature, TA, and air
motion are significant external factors, damped by overmolding.
The effect of varying power levels (Power Dissipation, PD), can
be estimated. The following formulas represent the fundamental
relationships used to estimate TJ, at PD.
PD = VIN
× IIN
(1)
T = PD
× RJA
(2)
TJ = TA + ΔT
(3)
For example, given common conditions such as: TA= 25°C,
VCC = 12 V, ICC = 4 mA, and RJA = 140 °C/W, then:
PD = VCC
× ICC = 12 V × 4 mA = 48 mW
T = PD
× RJA = 48 mW × 140 °C/W = 7°C
TJ = TA + T = 25°C + 7°C = 32°C
A worst-case estimate, PD(max), represents the maximum allow-
able power level (VCC(max), ICC(max)), without exceeding
TJ(max), at a selected RJA and TA.
Example: Reliability for VCC at TA=150°C, package LH, using a
low-K PCB.
Observe the worst-case ratings for the device, specifically:
RJA=110 °C/W, TJ(max) =165°C, VCC(max)= 24 V, and
ICC(max) = 17 mA.
Calculate the maximum allowable power level, PD(max). First,
invert equation 3:
Tmax = TJ(max) – TA = 165°C–150°C = 15°C
This provides the allowable increase to TJ resulting from internal
power dissipation. Then, invert equation 2:
PD(max) = Tmax÷RJA =15°C÷110 °C/W=136mW
Finally, invert equation 1 with respect to voltage:
VCC(est) = PD(max) ÷ ICC(max)= 136mW÷17 mA= 8 V
The result indicates that, at TA, the application and device can
dissipate adequate amounts of heat at voltages ≤VCC(est).
Compare VCC(est) to VCC(max). If VCC(est) ≤ VCC(max), then reli-
able operation between VCC(est) and VCC(max) requires enhanced
RJA. If VCC(est) ≥ VCC(max), then operation between VCC(est)
and VCC(max) is reliable under these conditions.
Power Derating
相关PDF资料 |
PDF描述 |
|---|---|
| A1244LUA-I1-T | MAGNETIC FIELD SENSOR-HALL EFFECT, -8-8mT, RECTANGULAR, THROUGH HOLE MOUNT |
| A1321LUA | MAGNETIC FIELD SENSOR-HALL EFFECT, 10mT, 0.20-4.70V, RECTANGULAR, THROUGH HOLE MOUNT |
| A1322ELHLT | MAGNETIC FIELD SENSOR-HALL EFFECT, 10mT, 0.20-4.70V, RECTANGULAR, SURFACE MOUNT |
| A1321L | MAGNETIC FIELD SENSOR-HALL EFFECT, 0.2-4.7V, RECTANGULAR, SURFACE MOUNT |
| A1322L | MAGNETIC FIELD SENSOR-HALL EFFECT, 0.2-4.7V, RECTANGULAR, SURFACE MOUNT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| A1244LLHLX-I2-T | 功能描述:IC HALL EFFECT LATCH SOT-23W RoHS:是 类别:传感器，转换器 >> 磁性 - 霍尔效应，数字式开关，线性，罗盘 (IC) 系列:- 标准包装:1 系列:- 传感范围:20mT ~ 80mT 类型:旋转 电源电压:4.5 V ~ 5.5 V 电流 - 电源:15mA 电流 - 输出（最大）:- 输出类型:数字式，PWM，8.5 位串行 特点:可编程 工作温度:-40°C ~ 150°C 封装/外壳:20-SSOP（0.209"，5.30mm 宽） 供应商设备封装:20-SSOP 包装:Digi-Reel® 其它名称:AS5132-HSST-500DKR |
| A1244LUA-I1-T | 功能描述:IC HALL EFFECT LATCH SIP-3 RoHS:是 类别:传感器，转换器 >> 磁性 - 霍尔效应，数字式开关，线性，罗盘 (IC) 系列:- 标准包装:1 系列:- 传感范围:20mT ~ 80mT 类型:旋转 电源电压:4.5 V ~ 5.5 V 电流 - 电源:15mA 电流 - 输出（最大）:- 输出类型:数字式，PWM，8.5 位串行 特点:可编程 工作温度:-40°C ~ 150°C 封装/外壳:20-SSOP（0.209"，5.30mm 宽） 供应商设备封装:20-SSOP 包装:Digi-Reel® 其它名称:AS5132-HSST-500DKR |
| A1244LUA-I2-T | 功能描述:IC HALL EFFECT LATCH SIP-3 RoHS:是 类别:传感器，转换器 >> 磁性 - 霍尔效应，数字式开关，线性，罗盘 (IC) 系列:- 标准包装:1 系列:- 传感范围:20mT ~ 80mT 类型:旋转 电源电压:4.5 V ~ 5.5 V 电流 - 电源:15mA 电流 - 输出（最大）:- 输出类型:数字式，PWM，8.5 位串行 特点:可编程 工作温度:-40°C ~ 150°C 封装/外壳:20-SSOP（0.209"，5.30mm 宽） 供应商设备封装:20-SSOP 包装:Digi-Reel® 其它名称:AS5132-HSST-500DKR |
| A1245LLHLT-I1-T | 功能描述:IC HALL EFFECT LATCH SOT23-3 制造商:allegro microsystems, llc 系列:- 包装:带卷（TR） 零件状态:有效 功能:卡销 技术:霍尔效应 极化:南极 感应范围:4mT 跳闸，-4mT 释放 测试条件:-40°C ~ 150°C 电压 - 电源:3 V ~ 24 V 电流 - 电源（最大值）:6.9mA 电流 - 输出（最大值）:- 输出类型:开路漏极 特性:- 工作温度:-40°C ~ 150°C（TA） 封装/外壳:TO-236-3，SC-59，SOT-23-3 供应商器件封装:SOT-23-3 标准包装:3,000 |
| A1245LLHLT-I2-T | 功能描述:IC HALL EFFECT LATCH SOT23-3 制造商:allegro microsystems, llc 系列:- 包装:带卷（TR） 零件状态:有效 功能:卡销 技术:霍尔效应 极化:南极 感应范围:4mT 跳闸，-4mT 释放 测试条件:-40°C ~ 150°C 电压 - 电源:3 V ~ 24 V 电流 - 电源（最大值）:5mA 电流 - 输出（最大值）:- 输出类型:开路漏极 特性:- 工作温度:-40°C ~ 150°C（TA） 封装/外壳:TO-236-3，SC-59，SOT-23-3 供应商器件封装:SOT-23-3 标准包装:3,000 |
发布紧急采购，3分钟左右您将得到回复。