- 您现在的位置：买卖IC网 > PDF目录253950 > A165S-J2A-2 ROTARY SWITCH-2POSITIONS, DPDT, LATCHED, 3A, 30VDC, PANEL MOUNT PDF资料下载
参数资料
| 型号： | A165S-J2A-2 |
| 元件分类： | 开关 |
| 英文描述： | ROTARY SWITCH-2POSITIONS, DPDT, LATCHED, 3A, 30VDC, PANEL MOUNT |
| 文件页数： | 7/17页 |
| 文件大小： | 1920K |
| 代理商： | A165S-J2A-2 |
A165S/W
15
Safety Precautions
Refer to Safety Precautions for All Pushbutton Switches.
Do not apply a voltage between the incandescent
lamp and the terminal that is greater than the rated
voltage. If the incandescent lamp is broken, the
operating part may pop out.
Always turn OFF the power and wait for 10 minutes
before replacing the incandescent lamp. If the lamp is
replaced immediately after the power is turned OFF,
the remaining heat may cause burns.
Mounting
Always make sure that the power is turned OFF before mounting,
removing, or wiring the Switch, or performing maintenance.
Do not tighten the mounting nut more than necessary using tools
such as pointed-nose pliers. Doing so will damage the mounting
nut.
The tightening torque is 0.29 to 0.49 Nm.
Wiring
Solder terminals and quick-connect terminals (#110) are commonly
used for terminals.
Be sure to use electrical wires that are a size appropriate for the
applied voltage and carry current (conductor size is 0.5 to 0.75
mm2). Perform soldering according to the conditions provided
below. If the soldering is not properly performed, the lead wires will
become detached, resulting in short-circuits.
1. Hand soldering: 350
°C, within 3 s
2. Dip soldering: 350
°C, within 3 s
Wait for one minute after soldering before exerting any external
force on the solder.
Use non-corrosive resin fluid as the flux.
Make sure that the electric cord is wired so that it does not touch
the Unit. If the electric cord touches the Unit, then electric wires with
a heat resistance of 100
°C min. must be used.
After wiring the Switch, maintain an appropriate clearance and
creepage distance.
Operating Environment
The IP65 model is designed with a degree of protection so that it
will not sustain damage if it is subjected to water from any direction
to the front of the panel.
Using the Microload
Insert a contact protection circuit, if necessary, to prevent the
reduction of life expectancy due to extreme wear on the contacts
caused by loads where inrush current occurs when the contact is
opened and closed.
The A16 allows both a standard load (125 V at 5A, 250 V at 3 A)
and a microload. If a standard load is applied, however, the
microload area cannot be used. If the microload area is used with a
standard load, the contact surface will become rough, and the
opening and closing of the contact for a microload may become
unreliable.
The minimum applicable load is the N-level reference value. This
value indicates the malfunction reference level for the reliability
level of 60% (
λ 60) (conforming to JIS C5003).
The equation,
λ 60 = 0.5 × 10-4/operations indicates that the
estimated malfunction rate is less than 1/2,000,000 operations with
a reliability level of 60%.
LED
The LED current-limiting resistor is built-in, so external resistance
is not required.
WARNING
Precautions for Correct Use
Rated voltage
Internal limiting resistor
5 VDC
Red, yellow: 300
Green: 160
12 VAC/VDC
Red, yellow: 1 k
Green: 910
24 VAC/VDC
2.4 k
Invalid
area
0.1
1
10
100
1,000
1 mA
5
12
24
30
0.15 mA
Current (mA)
V
oltage
(V)
0
Microload area
相关PDF资料 |
PDF描述 |
|---|---|
| A165W-A2MG-24D-2 | ROTARY SWITCH-2POSITIONS, DPDT, LATCHED, 3A, 30VDC, PANEL MOUNT |
| A018225 | KEYLOCK SWITCH, DPDT, LATCHED, PANEL MOUNT |
| A20415RNZGE | ROTARY SWITCH-4POSITIONS, DP4T, LATCHED, 0.35A, 125VDC, PANEL MOUNT-THREADED |
| A20442MNMCBE | ROTARY SWITCH-4POSITIONS, DP4T, LATCHED, 0.02A, 20VDC, THROUGH HOLE-STRAIGHT |
| A20442MSCGK | ROTARY SWITCH-4POSITIONS, DP4T, LATCHED, 0.35A, 125VDC, THROUGH HOLE-STRAIGHT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| A165SJ2M | 制造商:OMRON AUTOMATION AND SAFETY 功能描述:SWITCH UNIT RECT ALT 2POS BLACK 制造商:OMRON INDUSTRIAL AUTOMATION 功能描述:Switch Access Selector Switch Rectangular Operator |
| A165S-J2M | 功能描述:旋钮开关 KNOB-TYPE REC 2POS MAINT SELECTOR SWCH RoHS:否 制造商:C&K Components 位置数量:5 卡片组数量: 每卡片组极数:2 电流额定值:250 mA 电压额定值:125 V 指数角: 触点类型: 触点形式:DPST 端接类型:Solder 安装类型:Panel 触点电镀:Silver |
| A165SJ2M1 | 制造商:OMRON AUTOMATION AND SAFETY 功能描述:SWITCH KNOB RECT 2-POS SPDT 制造商:OMRON INDUSTRIAL AUTOMATION 功能描述:Switch Selector N.O./N.C. SPDT 90° Knob 5A 250VAC 30VDC Solder 250000Cycles Panel Mount 制造商:OMRON INDUSTRIAL AUTOMATION 功能描述:Electromechanical Switch Selector Switch N.O./N.C. SPDT 5A |
| A165S-J2M-1 | 功能描述:旋钮开关 KNOB-TYPE SQ 2POS MAINT SPDT SelecSwch RoHS:否 制造商:C&K Components 位置数量:5 卡片组数量: 每卡片组极数:2 电流额定值:250 mA 电压额定值:125 V 指数角: 触点类型: 触点形式:DPST 端接类型:Solder 安装类型:Panel 触点电镀:Silver |
| A165SJ2M2 | 制造商:OMRON AUTOMATION AND SAFETY 功能描述:SWITCH KNOB RECT ALT 2POS DPDT 制造商:Omron Electronic Components LLC 功能描述:Electromechanical Switch Selector Switch N.O./N.C. DPDT 5A 制造商:Omron Electronic Components LLC 功能描述:2 position rotary selector switch 制造商:OMRON INDUSTRIAL AUTOMATION 功能描述:Electromechanical Switch Selector Switch N.O./N.C. DPDT 5A 制造商:OMRON INDUSTRIAL AUTOMATION 功能描述:Switch Selector N.O./N.C. DPDT 90° Knob 5A 250VAC 30VDC Solder 250000Cycles Panel Mount |
发布紧急采购，3分钟左右您将得到回复。