- 您现在的位置：买卖IC网 > PDF目录210106 > A165W-A2MG-T1-2 ROTARY SWITCH-2POSITIONS, DPDT, LATCHED, 3A, 30VDC, PANEL MOUNT PDF资料下载
参数资料
| 型号： | A165W-A2MG-T1-2 |
| 元件分类： | 开关 |
| 英文描述： | ROTARY SWITCH-2POSITIONS, DPDT, LATCHED, 3A, 30VDC, PANEL MOUNT |
| 文件页数： | 14/45页 |
| 文件大小： | 1465K |
| 代理商： | A165W-A2MG-T1-2 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页当前第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页
A16/M16
A16/M16
22
Precautions
WARNING
Do not apply a voltage between the incandescent lamp and
the terminal that is greater than the rated voltage. If the incan-
descent lamp is broken, the operating part may pop out.
Always turn OFF the power and wait for 10 minutes before
replacing the incandescent lamp. If the lamp is replaced
immediately after the power is turned OFF, the remaining heat
may cause burns.
J
CORRECT USE
Mounting
Always make sure that the power is turned OFF before mounting,
removing, or wiring the Switch, or performing maintenance.
Do not tighten the mounting nut more than necessary using tools
such as pointed-nose pliers. Doing so will damage the mounting
nut. The tightening torque is 0.20 to 0.39 N m(3to5kgf cm).
Wiring
Solder terminals and quick-connect terminals (#110) are
commonly used for terminals.
Be sure to use electrical wires that are a size appropriate for the
applied voltage and carry current (conductor size is 0.5 to 0.75
mm2). Perform soldering according to the conditions provided
below. If the soldering is not properly performed, the lead wires
will become detached, resulting in short-circuits.
1. Hand soldering: 30 W, within 5 s
2. Dip soldering: 240°C, within 3 s
Wait for one minute after soldering before exerting any external
force on the solder.
Use non-corrosive resin fluid as the flux.
Make sure that the electric cord is wired so that it does not touch
the Unit. If the electric cord will touch the Unit, then electric wires
with a heat resistance of 100°C min. must be used.
After wiring the Switch, maintain an appropriate clearance and
creepage distance.
Operating Environment
The IP65 model is designed with a protective structure so that it
will not sustain damage if it is subjected to water from any
direction to the front of the panel.
Using the Microload
Insert a contact protection circuit, if necessary, to prevent the
reduction of life expectancy due to extreme wear on the contacts
caused by loads where inrush current occurs when the contact is
opened and closed.
The A16 allows both a general-purpose load (125 V at 5A, 250 V
at 3 A) and a microload. If a general-purpose load is applied,
however, the microload area cannot be used. If the microload
area is used with a general-purpose load, the contact surface will
become rough, and the opening and closing of the contact for a
microload may become unreliable.
The minimum applicable load is the N-level reference value. This
value indicates the malfunction reference level for the reliability
level of 60% (λ 60) (conforming to JIS C5003).
The equation, λ 60 = 0.5 x 10--4/time indicates that the estimated
malfunction rate is less than 1/2,000,000 with a reliability level of
60%.
Area of use
General-purpose load area
Microload area
Invalid
area
V
ol
tage
(V
)
Current (mA)
LEDs
The LED current-limiting resistor is built-in, so internal resistance
is not required.
Rated voltage
Internal limiting resistor
5VDC
33
12 VDC
270
24 VDC
1600
Others
The oil-resistant IP65 uses NBR rubber and is resistant to
general cutting oil and cooling oil. Some particular oils cannot be
used with the oil-resistant IP65, however, so contact your
OMRON representative for details.
If the panel is to be finished with coating, etc., make sure that the
panel meets the specified dimensions after the coating.
Do not subject the Switch to extreme shock or vibration. Doing so
will cause malfunctions and damage to the Switch.
Do not let sharp objects come into contact with the Switches that
are made of resin. Doing so will damage the Switches, causing
scratches on the outside of the operating parts, and malfunction.
When handling the Switches, do not throw or drop them.
Do not allow the Switch
to drop and hit the
ground.
Do not place or drop
heavy objects on the
Switch.
Do not operate the Switch
with hard or sharp objects.
Hammer Screwdriver
!
相关PDF资料 |
PDF描述 |
|---|---|
| A018304 | KEYLOCK SWITCH, 4PDT, MOMENTARY, PANEL MOUNT |
| A30303MSZBK | ROTARY SWITCH-3POSITIONS, 3P3T, LATCHED, 0.02A, 20VDC, PANEL MOUNT-THREADED |
| A11042RSMCBF | ROTARY SWITCH-10POSITIONS, SP10T, LATCHED, 0.02A, 20VDC, THROUGH HOLE-STRAIGHT |
| A110S1MNMCQE | ROTARY SWITCH-10POSITIONS, SP10T, LATCHED, 0.35A, 125VDC, THROUGH HOLE-STRAIGHT |
| A10042MNMCQF | ROTARY SWITCH-12POSITIONS, SP12T, LATCHED, 0.35A, 125VDC, THROUGH HOLE-STRAIGHT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| A165WA2MR | 制造商:OMRON AUTOMATION AND SAFETY 功能描述:SWITCH UNIT SQUARE ALT 2POS RED 制造商:OMRON INDUSTRIAL AUTOMATION 功能描述:Switch Access Selector Switch Square Operator |
| A165W-A2MR | 功能描述:旋钮开关 IL SQ 2POS MAINT RED Selector Switch RoHS:否 制造商:C&K Components 位置数量:5 卡片组数量: 每卡片组极数:2 电流额定值:250 mA 电压额定值:125 V 指数角: 触点类型: 触点形式:DPST 端接类型:Solder 安装类型:Panel 触点电镀:Silver |
| A165WA2MR24D1 | 制造商:OMRON AUTOMATION AND SAFETY 功能描述:SWITCH KNOB SQ 2-POS SPDT ILL 制造商:OMRON INDUSTRIAL AUTOMATION 功能描述:Electromechanical Switch Selector Switch N.O./N.C. SPDT 5A |
| A165W-A2MR-24D-1 | 功能描述:旋钮开关 IL SQ 2POS MNT 24V RED SPDT SELECT SWCH RoHS:否 制造商:C&K Components 位置数量:5 卡片组数量: 每卡片组极数:2 电流额定值:250 mA 电压额定值:125 V 指数角: 触点类型: 触点形式:DPST 端接类型:Solder 安装类型:Panel 触点电镀:Silver |
| A165WA2MR24D2 | 制造商:OMRON AUTOMATION AND SAFETY 功能描述:SWITCH KNOB SQUAR ILLUM 2POS RED 制造商:Omron Electronic Components LLC 功能描述:Electromechanical Switch Selector Switch N.O./N.C. DPDT 5A 制造商:OMRON INDUSTRIAL AUTOMATION 功能描述:Electromechanical Switch Selector Switch N.O./N.C. DPDT 5A |
发布紧急采购，3分钟左右您将得到回复。