- 您现在的位置：买卖IC网 > PDF目录235891 > A165W-A3AY-T1-2 ROTARY SWITCH-3POSITIONS, DPDT, MOMENTARY, 3A, 30VDC, PANEL MOUNT PDF资料下载
参数资料
| 型号： | A165W-A3AY-T1-2 |
| 元件分类： | 开关 |
| 英文描述： | ROTARY SWITCH-3POSITIONS, DPDT, MOMENTARY, 3A, 30VDC, PANEL MOUNT |
| 文件页数： | 39/45页 |
| 文件大小： | 1465K |
| 代理商： | A165W-A3AY-T1-2 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页当前第39页第40页第41页第42页第43页第44页第45页
M2BJ-B
M2BJ-B
45
Correct Use
J
NUT MOUNTING
Insert the buzzer unit from the front of the panel and tighten the
mounting nut inserted from the rear of the panel.
Since a projection exists on the rear portion of the buzzer unit, if
the mounting nut cannot be fitted into position, turn the nut
slightly.
The tightening torque of the mounting nut should be less than
5kg-cm.
Solder the terminals after mounting the nut. Otherwise, the
terminals, when thickened by solder, may prevent the nut from
being screwed down onto the buzzer unit.
J
MOUNTING
Tighten the mounting nut at a torque of less than 5 kg-cm.
J
WIRING
Exercise caution that the input terminals are not short-circuited
by the short-circuiting jumper.
Finish soldering within 5 seconds with a 30 watt soldering iron, or
within 3 seconds at a solder temperature of 240°C. For about a
minute after soldering, do not apply any force to the buzzer unit,
to avoid deforming the softened plastic buzzer unit base.
Use an non-corrosive, resin-based soldering flux.
J
SNAP-IN MOUNTING
Attach the mounting leaf spring to the buzzer. Engage the edges
of the leaf spring in the two grooves on the threaded section of
the buzzer. After inserting the leaf spring edges into the grooves,
confirm that the leaf spring has seated. Be sure to attach both
leaf springs.
Insert the buzzer assembly into the hole on the mounting panel
from the front.
J
SHORT-CIRCUITING JUMPER
The buzzer sounds continuously or intermittently depending on
how the short-circuiting bracket is attached to the case guide.
When the bracket is attached with the triangle on it facing
direction A (PC board side), the buzzer sounds intermittently.
To produce continuous sounds, attach the bracket to the case
guide so that the triangle on the bracket faces direction B.
相关PDF资料 |
PDF描述 |
|---|---|
| A165W-T3MG-T1-2 | ROTARY SWITCH-3POSITIONS, DPDT, LATCHED, 3A, 30VDC, PANEL MOUNT |
| A165W-T2MG-24D-1 | ROTARY SWITCH-2POSITIONS, SPDT, LATCHED, 3A, 30VDC, PANEL MOUNT |
| A101MD9AV2Q | TOGGLE SWITCH, SPDT, LATCHED, 2A, 30VDC, THROUGH HOLE-RIGHT ANGLE |
| A6S-7102-PH | SLIDE DIP SWITCH-7SWITCHES, 7PST, LATCHED,0.025A, 24VDC, SURFACE MOUNT-STRAIGHT |
| A6E-7101 | SLIDE DIP SWITCH-1SWITCHES, 7PST, LATCHED,0.025A, 24VDC, THROUGH HOLE-STRAIGHT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| A165WA3MG | 制造商:OMRON AUTOMATION AND SAFETY 功能描述:SWITCH UNIT SQUARE ALT 3POS GRN 制造商:OMRON INDUSTRIAL AUTOMATION 功能描述:Switch Access Selector Switch Square Operator |
| A165W-A3MG | 功能描述:旋钮开关 IL SQ 3POS MAINT GRN Selector Switch RoHS:否 制造商:C&K Components 位置数量:5 卡片组数量: 每卡片组极数:2 电流额定值:250 mA 电压额定值:125 V 指数角: 触点类型: 触点形式:DPST 端接类型:Solder 安装类型:Panel 触点电镀:Silver |
| A165WA3MG24D2 | 制造商:OMRON INDUSTRIAL AUTOMATION 功能描述:Electromechanical Switch Selector Switch N.O./N.C. DPDT 5A |
| A165W-A3MG-24D-2 | 功能描述:旋钮开关 SQ 3PS MNT 24VDC GRN IP65 DPDT Illum RoHS:否 制造商:C&K Components 位置数量:5 卡片组数量: 每卡片组极数:2 电流额定值:250 mA 电压额定值:125 V 指数角: 触点类型: 触点形式:DPST 端接类型:Solder 安装类型:Panel 触点电镀:Silver |
| A165WA3MG24D2OMA | 制造商:OMRON AUTOMATION AND SAFETY 功能描述:SWITCH KNOB SQ 3-POS DPDT ILL |
发布紧急采购，3分钟左右您将得到回复。