- 您现在的位置：买卖IC网 > PDF目录235896 > A22-DB-02A PUSHBUTTON SWITCH, DPST, MOMENTARY, 10A, 24VDC, PANEL MOUNT-THREADED PDF资料下载
参数资料
| 型号： | A22-DB-02A |
| 元件分类： | 开关 |
| 英文描述： | PUSHBUTTON SWITCH, DPST, MOMENTARY, 10A, 24VDC, PANEL MOUNT-THREADED |
| 文件页数： | 20/30页 |
| 文件大小： | 5020K |
| 代理商： | A22-DB-02A |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页当前第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页
A22
27
Securing the Connector Cable
1. Insert the connector into the cable port hole in the Box and secure
with the fixing nut inside the box.
2. Open a hole in the thin rubber section of the rubber ring.
3. Pass the tightening cap through the cable, insert the cable into the
connector, and tighten the hexagonal nut to secure the cable.
Switch Blocks
Installing the Switch Blocks
Hook the small protrusion on the Switch Block into the groove on
the Mounting Latch on the other side of the lever, then push up the
Switch Block in the direction indicated by the arrow in the figure
below.
Removing the Switch Blocks
Insert a screwdriver between the Mounting Latch and the Switch
Block, then push down the screwdriver in the direction indicated by
the arrow in the following figure.
Wiring
Wiring Round Crimp Terminals
Loosen the terminal screw from the Switch Unit until it completely
comes off the groove, insert a screwdriver as shown in the following
figure, then push up the washer in the direction indicated by the
arrow to temporarily secure it. Now, a round crimp terminal can be
connected. After inserting the terminal, tighten the screws to
complete wiring.
Engraving
Engrave the characters on the surface on the
Cap. Make sure that the characters are
aligned parallel to the imaginary line
connecting the two protruding portions to the
left and right of the Cap.
The characters must not be engraved deeper
than 0.5 mm. Apply an alcohol-based paint
coating, such as melamine, alkyd, or acrylic
resin paint coating, to the engraved
characters.
Cable diameter
Connector
7 to 9 dia.
A22Z-3500-1
9 to 11 dia.
A22Z-3500-2
Fixing nut
Rubber washer
Connector
Tightening cap
Cable
Inside
Outside
Box
Mounting
Latch
Lever
Protrusion
Switch Block
Use either of the following screwdrivers.
Flat-head
screwdriver
Phillips
screwdriver
3 to 6 mm
Screwdriver
Washer
Screw
Protruding portions
on Cap
相关PDF资料 |
PDF描述 |
|---|---|
| A22-TB-01A | PUSHBUTTON SWITCH, SPST, MOMENTARY, 10A, 24VDC, PANEL MOUNT-THREADED |
| AP4N400SWBE | PUSHBUTTON SWITCH, SPST, MOMENTARY, 0.2A, 24VDC, PANEL MOUNT |
| AP4N602SZBE | PUSHBUTTON SWITCH, SPST, MOMENTARY, 0.2A, 24VDC, PANEL MOUNT |
| A22L-GG-12A-02M | PUSHBUTTON SWITCH, DPST, MOMENTARY, 10A, 24VDC, PANEL MOUNT-THREADED |
| A22L-GG-T1-01A | PUSHBUTTON SWITCH, SPST, MOMENTARY, 10A, 24VDC, PANEL MOUNT-THREADED |
相关代理商/技术参数 |
参数描述 |
|---|---|
| A22DB02M | 制造商:OMRON AUTOMATION AND SAFETY 功能描述:SWITCH PUSH DPST-NC 10A 110V 制造商:OMRON INDUSTRIAL AUTOMATION 功能描述:Switch Push Button N.C. DPST Square Button 10A 440VAC 380VDC Momentary Contact Screw Panel Mount |
| A22-DB-02M | 功能描述:按钮开关 DPST-NC MOM SQ BLACK Full-guard actuator RoHS:否 制造商:C&K Components 触点形式:2 NC - 2 NO 开关功能:ON ? OFF 电流额定值:4 A 电压额定值 AC:12 V to 250 V 电压额定值 DC:12 V to 50 V 功率额定值: 安装风格:Through Hole 照明:Illuminated 照明颜色:None IP 等级:IP 40 端接类型:Solder 触点电镀:Silver 执行器:Square 盖颜色: 封装: 可燃性等级:UL 94 V-0 |
| A22DB10A | 制造商:Omron Electronic Components LLC 功能描述:Switch Push Button N.O. SPST Square Button 10A 440VAC 380VDC Alternate Contact Screw Panel Mount 制造商:OMRON INDUSTRIAL AUTOMATION 功能描述:Switch Push Button N.O. SPST Square Button 10A 440VAC 380VDC Alternate Contact Screw Panel Mount |
| A22-DB-10A | 功能描述:按钮开关 SPST-NO ALT SQ BLACK Full-guard actuator RoHS:否 制造商:C&K Components 触点形式:2 NC - 2 NO 开关功能:ON ? OFF 电流额定值:4 A 电压额定值 AC:12 V to 250 V 电压额定值 DC:12 V to 50 V 功率额定值: 安装风格:Through Hole 照明:Illuminated 照明颜色:None IP 等级:IP 40 端接类型:Solder 触点电镀:Silver 执行器:Square 盖颜色: 封装: 可燃性等级:UL 94 V-0 |
| A22DB10AOMA | 制造商:OMRON AUTOMATION AND SAFETY 功能描述:SWITCH PUSH SPST-NO 10A 110V |
发布紧急采购，3分钟左右您将得到回复。