- 您现在的位置：买卖IC网 > PDF目录364573 > A29800SERIES 1024K X 8 Bit / 512K X 16 Bit CMOS 5.0 Volt-only. Boot Sector Flash Memory PDF资料下载
参数资料
| 型号： | A29800SERIES |
| 英文描述： | 1024K X 8 Bit / 512K X 16 Bit CMOS 5.0 Volt-only. Boot Sector Flash Memory |
| 中文描述： | 1024K × 8位/ 16位为512k ×电压的CMOS 5.0只。引导扇区闪存 |
| 文件页数： | 5/34页 |
| 文件大小： | 341K |
| 代理商： | A29800SERIES |
第1页第2页第3页第4页当前第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页
A29800 Series
PRELIMINARY (December, 2002, Version 0.1)
5
AMIC Technology, Corp.
Word/Byte Configuration
The
BYTE
pin determines whether the I/O pins I/O
15
-I/O
0
operate in the byte or word configuration. If the
BYTE
pin
is set at logic ”1”, the device is in word configuration, I/O
15
-
I/O
0
are active and controlled by
CE
and
OE
.
If the
BYTE
pin is set at logic “0”, the device is in byte
configuration, and only I/O
0
-I/O
7
are active and controlled
by
CE
and
OE
. I/O
8
-I/O
14
are tri-stated, and I/O
15
pin is
used as an input for the LSB(A-1) address function.
Requirements for Reading Array Data
To read array data from the outputs, the system must drive
the
CE
and
OE
pins to V
IL
.
CE
is the power control and
selects the device.
OE
is the output control and gates
array data to the output pins.
WE
should remain at V
IH
all
the time during read operation. The internal state machine
is set for reading array data upon device power-up, or after
a hardware reset. This ensures that no spurious alteration
of the memory content occurs during the power transition.
No command is necessary in this mode to obtain array
data. Standard microprocessor read cycles that assert valid
addresses on the device address inputs produce valid data
on the device data outputs. The device remains enabled for
read access until the command register contents are
altered.
See "Reading Array Data" for more information. Refer to the
AC Read Operations table for timing specifications and to
the Read Operations Timings diagram for the timing
waveforms, l
CC1
in the DC Characteristics table represents
the active current specification for reading array data.
Writing Commands/Command Sequences
To write a command or command sequence (which
includes programming data to the device and erasing
sectors of memory), the system must drive
WE
and
CE
to
V
IL
, and
OE
to V
IH
. An erase operation can erase one
sector, multiple sectors, or the entire device. The Sector
Address Tables indicate the address range that each sector
occupies. A "sector address" consists of the address inputs
required to uniquely select a sector. See the "Command
Definitions" section for details on erasing a sector or the
entire chip, or suspending/resuming the erase operation.
After the system writes the autoselect command sequence,
the device enters the autoselect mode. The system can
then read autoselect codes from the internal register (which
is separate from the memory array) on I/O
7
- I/O
0
. Standard
read cycle timings apply in this mode. Refer to the
"Autoselect Mode" and "Autoselect Command Sequence"
sections for more information.
I
CC2
in the DC Characteristics table represents the active
current specification for the write mode. The "AC
Characteristics" section contains timing specification tables
and timing diagrams for write operations.
Program and Erase Operation Status
During an erase or program operation, the system may
check the status of the operation by reading the status bits
on I/O
7
- I/O
0
. Standard read cycle timings and I
CC
read
specifications apply. Refer to "Write Operation Status" for
more information, and to each AC Characteristics section
for timing diagrams.
Standby Mode
When the system is not reading or writing to the device, it
can place the device in the standby mode. In this mode,
current consumption is greatly reduced, and the outputs are
placed in the high impedance state, independent of the
OE
input.
The device enters the CMOS standby mode when the
CE
&
RESET
pins are both held at V
CC
±
0.5V. (Note that this
is a more restricted voltage range than V
IH
.) The device
enters the TTL standby mode when
CE
is held at V
IH
, while
RESET
is held at VCC
±
0.5V. The device requires the
standard access time (t
CE
) before it is ready to read data.
If the device is deselected during erasure or programming,
the device draws active current until the operation is
completed.
I
CC3
in the DC Characteristics tables represents the standby
current specification.
Output Disable Mode
When the
OE
input is at V
IH
, output from the device is
disabled. The output pins are placed in the high impedance
state.
RESET
: Hardware Reset Pin
The
RESET
pin provides a hardware method of resetting
the device to reading array data. When the system drives
the
RESET
pin low for at least a period of t
RP
, the device
immediately terminates any operation in progress, tristates
all data output pins, and ignores all read/write attempts for
the duration of the
RESET
pulse. The device also resets
the internal state machine to reading array data. The
operation that was interrupted should be reinitiated once
the device is ready to accept another command sequence,
to ensure data integrity.
The
RESET
pin may be tied to the system reset circuitry. A
system reset would thus also reset the Flash memory,
enabling the system to read the boot-up firmware from the
Flash memory.
Refer to the AC Characteristics tables for
RESET
parameters and diagram.
相关PDF资料 |
PDF描述 |
|---|---|
| A2982ELW | Octal Peripheral Driver |
| A2982SLWTR | Octal Peripheral Driver |
| A2982 | 8-CHANNEL SOURCE DRIVERS |
| A2982SLW | 8-CHANNEL SOURCE DRIVERS |
| UDQ2982A | High temperature 16 A Triacs |
相关代理商/技术参数 |
参数描述 |
|---|---|
| A29800TM-55 | 制造商:AMICC 制造商全称:AMIC Technology 功能描述:1024K X 8 Bit / 512K X 16 Bit CMOS 5.0 Volt-only, Boot Sector Flash Memory |
| A29800TM-70 | 制造商:AMICC 制造商全称:AMIC Technology 功能描述:1024K X 8 Bit / 512K X 16 Bit CMOS 5.0 Volt-only, Boot Sector Flash Memory |
| A29800TM-90 | 制造商:AMICC 制造商全称:AMIC Technology 功能描述:1024K X 8 Bit / 512K X 16 Bit CMOS 5.0 Volt-only, Boot Sector Flash Memory |
| A29800TV-55 | 制造商:AMICC 制造商全称:AMIC Technology 功能描述:1024K X 8 Bit / 512K X 16 Bit CMOS 5.0 Volt-only, Boot Sector Flash Memory |
| A29800TV-70 | 制造商:AMICC 制造商全称:AMIC Technology 功能描述:1024K X 8 Bit / 512K X 16 Bit CMOS 5.0 Volt-only, Boot Sector Flash Memory |
发布紧急采购，3分钟左右您将得到回复。