- 您现在的位置：买卖IC网 > PDF目录364573 > A29L800SERIES 1M X 8 Bit / 512K X 16 Bit CMOS 3.0 Volt-only. Boot Sector Flash Memory PDF资料下载
参数资料
| 型号： | A29L800SERIES |
| 英文描述： | 1M X 8 Bit / 512K X 16 Bit CMOS 3.0 Volt-only. Boot Sector Flash Memory |
| 中文描述： | 100万× 8位/ 16位为512k ×电压的CMOS 3.0只。引导扇区闪存 |
| 文件页数： | 2/41页 |
| 文件大小： | 396K |
| 代理商： | A29L800SERIES |
第1页当前第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页
General Description
A29L800 Series
PRELIMINARY (September, 2002, Version 0.2)
2
AMIC Technology, Inc.
The A29L800 is an 8Mbit, 3.0 volt-only Flash memory
organized as 1,048,576 bytes of 8 bits or 524,288 words of
16 bits each. The 8 bits of data appear on I/O
0
- I/O
7
; the 16
bits of data appear on I/O
0
~I/O
15
. The A29L800 is offered in
48-ball TFBGA,
44-pin SOP and 48-Pin TSOP packages.
This device is designed to be programmed in-system with the
standard system 3.0 volt VCC supply. Additional 12.0 volt
VPP is not required for in-system write or erase operations.
However, the A29L800 can also be programmed in standard
EPROM programmers.
The A29L800 has the first toggle bit, I/O
6
, which indicates
whether an Embedded Program or Erase is in progress, or it
is in the Erase Suspend. Besides the I/O
6
toggle bit, the
A29L800 has a second toggle bit, I/O
2
, to indicate whether
the addressed sector is being selected for erase. The
A29L800 also offers the ability to program in the Erase
Suspend mode. The standard A29L800 offers access times
of 70 and 90ns, allowing high-speed microprocessors to
operate without wait states. To eliminate bus contention the
device has separate chip enable (
CE
), write enable (
WE
)
and output enable (
OE
) controls.
The device requires only a single 3.0 volt power supply for
both read and write functions. Internally generated and
regulated voltages are provided for the program and erase
operations.
The A29L800 is entirely software command set compatible
with the JEDEC single-power-supply Flash standard.
Commands are written to the command register using
standard microprocessor write timings. Register contents
serve as input to an internal state-machine that controls the
erase and programming circuitry. Write cycles also internally
latch addresses and data needed for the programming and
erase operations. Reading data out of the device is similar to
reading from other Flash or EPROM devices.
Device programming occurs by writing the proper program
command sequence. This initiates the Embedded Program
algorithm - an internal algorithm that automatically times the
program pulse widths and verifies proper program margin.
Device erasure occurs by executing the proper erase
command sequence. This initiates the Embedded Erase
algorithm - an internal algorithm that automatically
preprograms the array (if it is not already programmed)
before executing the erase operation. During erase, the
device automatically times the erase pulse widths and
verifies proper erase margin. The Unlock Bypass mode
facilitates faster programming times by requiring only two
write cycles to program data instead of four.
The host system can detect whether a program or erase
operation is complete by observing the RY /
BY
pin, or
by
reading the I/O
7
(
Data
Polling) and I/O
6
(toggle) status bits.
After a program or erase cycle has been completed, the
device is ready to read array data or accept another
command.
The sector erase architecture allows memory sectors to be
erased and reprogrammed without affecting the data
contents of other sectors. The A29L800 is fully erased when
shipped from the factory.
The hardware sector protection feature disables operations
for both program and erase in any combination of the
sectors of memory. This can be achieved via programming
equipment.
The Erase Suspend/Erase Resume feature enables the user
to put erase on hold for any period of time to read data from,
or program data to, any other sector that is not selected for
erasure. True background erase can thus be achieved.
The hardware
RESET
pin terminates any operation in
progress and resets the internal state machine to reading
array data. The
RESET
pin may be tied to the system reset
circuitry. A system reset would thus also reset the device,
enabling the system microprocessor to read the boot-up
firmware from the Flash memory.
The device offers two power-saving features. When
addresses have been stable for a specified amount of time,
the device enters the automatic sleep mode. The system can
also place the device into the standby mode. Power
consumption is greatly reduced in both these modes.
相关PDF资料 |
PDF描述 |
|---|---|
| A31-1 | 10 TO 2000 MHz CECASCADABLE AMPLIFIER |
| A3134*LT | BIPOLAR HALL-EFFECT SWITCH FOR HIGH-TEMPERATURE OPERATION |
| A3134*UA | BIPOLAR HALL-EFFECT SWITCH FOR HIGH-TEMPERATURE OPERATION |
| A3134ELL | Hall-Effect Switch |
| A3134ELT | BIPOLAR HALL-EFFE T SWITCH FOR HIGH-TEMPERATURE OPERATION |
相关代理商/技术参数 |
参数描述 |
|---|---|
| A29L800TG-70 | 制造商:AMICC 制造商全称:AMIC Technology 功能描述:1M X 8 Bit / 512K X 16 Bit CMOS 3.0 Volt-only, Boot Sector Flash Memory |
| A29L800TG-90 | 制造商:AMICC 制造商全称:AMIC Technology 功能描述:1M X 8 Bit / 512K X 16 Bit CMOS 3.0 Volt-only, Boot Sector Flash Memory |
| A29L800TG-90U | 制造商:AMICC 制造商全称:AMIC Technology 功能描述:1M X 8 Bit / 512K X 16 Bit CMOS 3.0 Volt-only, Boot Sector Flash Memory |
| A29L800TM-70 | 制造商:AMICC 制造商全称:AMIC Technology 功能描述:1M X 8 Bit / 512K X 16 Bit CMOS 3.0 Volt-only, Boot Sector Flash Memory |
| A29L800TM-90 | 制造商:AMICC 制造商全称:AMIC Technology 功能描述:1M X 8 Bit / 512K X 16 Bit CMOS 3.0 Volt-only, Boot Sector Flash Memory |
发布紧急采购，3分钟左右您将得到回复。