- 您现在的位置：买卖IC网 > PDF目录298734 > A3241LUA (Allegro MicroSystems, Inc.) Chopper-Stabilized Unipolar Hall-Effect Switches PDF资料下载
参数资料
| 型号： | A3241LUA |
| 厂商： | Allegro MicroSystems, Inc. |
| 英文描述： | Chopper-Stabilized Unipolar Hall-Effect Switches |
| 中文描述： | 斩波稳定单极霍尔效应开关 |
| 文件页数： | 12/12页 |
| 文件大小： | 401K |
| 代理商： | A3241LUA |
9
A3241-DS, Rev. 2
Worcester, Massachusetts 01615-0036 (508) 853-5000
115 Northeast Cutoff, Box 15036
www.allegromicro.com
Allegro MicroSystems, Inc.
Chopper-Stabilized Unipolar Hall Effect Switches
A3241 and A3242
Figure 2. Chopper Stabilization Circuit (Dynamic Quadrature Offset Cancellation)
Amp
Regulator
Clock/Logic
Hall Element
Sa
mp
le
an
d
Ho
ld
Lo
w-P
as
s
Filte
r
Chopper Stabilization Technique
When using Hall-effect technology, a limiting factor for
switchpoint accuracy is the small signal voltage developed
across the Hall element. This voltage is disproportionally small
relative to the offset that can be produced at the output of the
Hall sensor. This makes it difcult to process the signal while
maintaining an accurate, reliable output over the specied oper-
ating temperature and voltage ranges.
Chopper stabilization is a unique approach used to minimize
Hall offset on the chip. The patented Allegro technique, namely
Dynamic Quadrature Offset Cancellation, removes key sources
of the output drift induced by thermal and mechanical stresses.
This offset reduction technique is based on a signal modulation-
demodulation process. The undesired offset signal is separated
from the magnetic-eld-induced signal in the frequency domain,
through modulation. The subsequent demodulation acts as a
modulation process for the offset, causing the magnetic-eld-
induced signal to recover its original spectrum at baseband,
while the dc offset becomes a high-frequency signal. The mag-
netic-eld-induced signal then can pass through a low-pass lter,
while the modulated dc offset is suppressed. This conguration
is illustrated in gure 2.
The chopper stabilization technique uses a 200 kHz high-fre-
quency clock. For demodulation process, a sample and hold
technique is used, where the sampling is performed at twice the
chopper frequency (400 kHz). This high-frequency operation
allows a greater sampling rate, which results in higher accuracy
and faster signal-processing capability. This approach desensi-
tizes the chip to the effects of thermal and mechanical stresses,
and produces devices that have extremely stable quiescent Hall
output voltages and precise recoverability after temperature
cycling. This technique is made possible through the use of a
BiCMOS process, which allows the use of low-offset, low-noise
ampliers in combination with high-density logic integration and
sample-and-hold circuits.
The repeatability of magnetic-eld-induced switching is affected
slightly by a chopper technique. However, the Allegro high-
frequency chopping approach minimizes the affect of jitter and
makes it imperceptible in most applications. Applications that
are more likely to be sensitive to such degradation are those
requiring precise sensing of alternating magnetic elds; for
example, speed sensing of ring-magnet targets. For such applica-
tions, Allegro recommends its digital sensor families with lower
sensitivity to jitter. For more information on those devices,
contact your Allegro sales representative.
相关PDF资料 |
PDF描述 |
|---|---|
| A3281ELT | HALL-EFFECT LATCHES FOR HIGH-TEMPERATURE OPERATION |
| A3421EKA | HALL-EFFECT, DIRECTION-DETECTION SENSORS |
| A3425LL-T | SPECIALTY ANALOG CIRCUIT, PDSO8 |
| A3FSDBX13 | GENERAL PURPOSE AUDIO CONNECTOR |
| A3FSDBXAU01 | GENERAL PURPOSE AUDIO CONNECTOR |
相关代理商/技术参数 |
参数描述 |
|---|---|
| A3241LUA-T | 功能描述:IC SWITCH HALL EFFECT 3-SIP RoHS:是 类别:传感器，转换器 >> 磁性 - 霍尔效应，数字式开关，线性，罗盘 (IC) 系列:- 标准包装:1 系列:- 传感范围:20mT ~ 80mT 类型:旋转 电源电压:4.5 V ~ 5.5 V 电流 - 电源:15mA 电流 - 输出（最大）:- 输出类型:数字式，PWM，8.5 位串行 特点:可编程 工作温度:-40°C ~ 150°C 封装/外壳:20-SSOP（0.209"，5.30mm 宽） 供应商设备封装:20-SSOP 包装:Digi-Reel® 其它名称:AS5132-HSST-500DKR |
| A3242 | 制造商:ALLEGRO 制造商全称:Allegro MicroSystems 功能描述:Chopper-Stabilized Unipolar Hall-Effect Switches |
| A3242ELHLT | 功能描述:IC SWITCH HALL EFFECT SOT23W RoHS:否 类别:传感器，转换器 >> 磁性 - 霍尔效应，数字式开关，线性，罗盘 (IC) 系列:- 标准包装:1 系列:- 传感范围:20mT ~ 80mT 类型:旋转 电源电压:4.5 V ~ 5.5 V 电流 - 电源:15mA 电流 - 输出（最大）:- 输出类型:数字式，PWM，8.5 位串行 特点:可编程 工作温度:-40°C ~ 150°C 封装/外壳:20-SSOP（0.209"，5.30mm 宽） 供应商设备封装:20-SSOP 包装:Digi-Reel® 其它名称:AS5132-HSST-500DKR |
| A3242ELHLT-T | 功能描述:IC SWITCH HALL EFFECT SOT23W RoHS:是 类别:传感器，转换器 >> 磁性 - 霍尔效应，数字式开关，线性，罗盘 (IC) 系列:- 标准包装:1 系列:- 传感范围:20mT ~ 80mT 类型:旋转 电源电压:4.5 V ~ 5.5 V 电流 - 电源:15mA 电流 - 输出（最大）:- 输出类型:数字式，PWM，8.5 位串行 特点:可编程 工作温度:-40°C ~ 150°C 封装/外壳:20-SSOP（0.209"，5.30mm 宽） 供应商设备封装:20-SSOP 包装:Digi-Reel® 其它名称:AS5132-HSST-500DKR |
| A3242EUA | 功能描述:IC SWITCH HALL EFFECT 3-SIP RoHS:否 类别:传感器，转换器 >> 磁性 - 霍尔效应，数字式开关，线性，罗盘 (IC) 系列:- 标准包装:1 系列:- 传感范围:20mT ~ 80mT 类型:旋转 电源电压:4.5 V ~ 5.5 V 电流 - 电源:15mA 电流 - 输出（最大）:- 输出类型:数字式，PWM，8.5 位串行 特点:可编程 工作温度:-40°C ~ 150°C 封装/外壳:20-SSOP（0.209"，5.30mm 宽） 供应商设备封装:20-SSOP 包装:Digi-Reel® 其它名称:AS5132-HSST-500DKR |
发布紧急采购，3分钟左右您将得到回复。