- 您现在的位置：买卖IC网 > PDF目录16488 > A3935KLQ (Allegro Microsystems Inc)IC CTRLR MOSFET 3PH 36-SOIC PDF资料下载
参数资料
| 型号： | A3935KLQ |
| 厂商： | Allegro Microsystems Inc |
| 文件页数： | 8/13页 |
| 文件大小： | 0K |
| 描述： | IC CTRLR MOSFET 3PH 36-SOIC |
| 标准包装： | 31 |
| 应用： | DC 电机驱动器，无刷（BLDC），3 相 |
| 输出数： | 1 |
| 电压 - 负载： | 7 V ~ 40 V |
| 电源电压： | 4.75 V ~ 5.25 V |
| 工作温度： | -40°C ~ 135°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 36-QSOP |
| 供应商设备封装： | 36-QSOP |
| 包装： | 管件 |
A3935
3-Phase Power MOSFET Controller for Automotive Applications
Terminal Descriptions
AHI, BHI, and CHI. Direct control of high-side gate outputs
GHA, GHB, and GHC. Logic 1 drives the gate on. Logic 0 pulls
the gate down, turning off the external power MOSFET. Inter-
nally pulled down when the terminal is open.
ALO, BLO, and CLO. Direct control of low-side gate outputs
GHA, GHB, and GHC. Logic 1 drives the gate on. Logic 0 pulls
the gate down, turning off the external power MOSFET . Inter-
nally pulled down when the terminal is open.
BOOSTD. Boost converter switch drain connection .
BOOSTS. Boost converter switch source connection.
CA, CB, and CC. High-side connection for the bootstrap
capacitors, CBOOT x , positive supply for high-side gate drive.
The bootstrap capacitor is charged to V REG when the output S x
terminal is low. When the output swings high, the voltage on this
terminal rises with the output to provide the boosted gate voltage
needed for N-channel power MOSFETs.
CSN. Input for current-sense differential amplifier, on the
inverting, negative side. Kelvin connection for the ground side of
the current-sense resistor, RSENSE.
CSOUT. Amplifier output voltage proportional to the current
sensed across an external low-value resistor placed in the ground
side of the power MOSFET bridge.
CSP. Input for current-sense differential amplifier, on the non-
inverting, positive side. Connected to the positive side of the
sense resistor, RSENSE.
ENABLE. Logic 0 disables the gate control signals and switches
off all the gate drivers (low) causing a coast condition. Can be
used in conjunction with the gate inputs to PWM (pulse wave
modulate) the load current. Internally pulled down when the
terminal is open.
ˉFˉ ˉAˉ ˉUˉ ˉLˉ ˉTˉ . Diagnostic logic output signal. When low, indicates
that one or more fault conditions have occurred.
GHA, GHB, and GHC. High-side gate drive outputs for
N-channel MOSFET drivers. External series gate resistors can
control the slew rate seen at the power driver gate, thereby
controlling the di / dt and dv / dt of S x outputs.
GLA, GLB, and GLC. Low-side gate drive outputs for external,
N-channel MOSFET drivers. External series gate resistors can
control slew rate.
GND. Ground, or negative, side of VDD and VBAT supplies.
LSS. Low-side gate driver return. Connects to the common
sources on the low sides of the power MOSFET bridge.
OVFLT. Logic 1 indicates that the V BAT level exceeded the
VBAT overvoltage trip point set by the OVSET level. It will
recover after exceeding a hysteresis below that maximum value.
Normally, it has a high-impedance state. If OVFLT and UVFLT
are both in high-impedance state; then, at least, a thermal
shutdown or VDD undervoltage has occurred.
OVSET. A positive dc level that controls the VBAT overvoltage
trip point. Usually, set by a precision resistor divider network
between VDD and GND, but can be held grounded for a preset
value. When this terminal is open, it sets an unspecified but high
overvoltage trip point.
SA, SB, and SC. Directly connected to the motor terminals,
these terminals sense the voltages switched across the load and
are connected to the negative side of the bootstrap capacitors,
CBOOT x . Also, are the negative supply connection for the
floating high-side drivers.
UVFLT. Logic 1 indicates that the V BAT level is below its
minimum value. It will recover after exceeding a hysteresis above
that minimum value. Has a high-impedance state. If UVFLT and
OVFLT are both in high-impedance state; then, at least, a thermal
shutdown or VDD undervoltage has occurred.
VBAT. Battery voltage. Positive input. usually connected to the
motor voltage supply.
VBOOST. Boost converter output, 16 V nominal, is also the
input to the regulator for VREG. Has internal boost-current
and boost-voltage control loops. In high-voltage systems is
approximately one diode drop below V BAT .
VDD. Logic supply, +5 V nominal.
VDRAIN. Kelvin connection for drain-to-source voltage monitor.
Connected to the high-side drains of the MOSFET bridge. High
impedance when this terminal is open, and registers as a short-to-
ground fault on all motor phases.
VDSTH. A positive dc level that sets the drain-to-source monitor
threshold voltage. Internally pulled down when this terminal is
open.
VREG. High-side gate driver supply, 13.5 V nominal. Has low-
voltage dropout (LDO) feature.
Allegro MicroSystems, Inc.
115 Northeast Cutoff, Box 15036
Worcester, Massachusetts 01615-0036 (508) 853-5000
www.allegromicro.com
8
相关PDF资料 |
PDF描述 |
|---|---|
| 9-6278027-9 | CA 62.5/125 ZIP ST MT-RJ 0.5M |
| GBM36DRUH | CONN EDGECARD 72POS DIP .156 SLD |
| VI-24N-EX | CONVERTER MOD DC/DC 18.5V 75W |
| GBM28DRTI | CONN EDGECARD 56POS DIP .156 SLD |
| XR16M570IL32-0B-EB | EVAL BOARD FOR XR16M570-B 32QFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| A3935KLQ-01 | 制造商:Allegro MicroSystems LLC 功能描述: |
| A3935KLQ-T | 功能描述:IC CTRLR MOSFET 3PH 36-SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 电机和风扇控制器，驱动器 系列:- 标准包装:1 系列:- 应用:直流电机驱动器，步进电机驱动器 评估套件:- 输出数:1 或 2 电流 - 输出:750mA 电压 - 负载:10 V ~ 40 V 电源电压:4.5 V ~ 5.5 V 工作温度:-20°C ~ 70°C 安装类型:表面贴装 封装/外壳:24-BFSOP（0.295"，7.50mm 宽） 供应商设备封装:24-SOP 包装:Digi-Reel® 其它名称:MTS62C19A-HS105DKR |
| A3935KLQTR | 功能描述:IC CTRLR MOSFET 3PH 36-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 电机和风扇控制器，驱动器 系列:- 标准包装:1 系列:- 应用:直流电机驱动器，步进电机驱动器 评估套件:- 输出数:1 或 2 电流 - 输出:750mA 电压 - 负载:10 V ~ 40 V 电源电压:4.5 V ~ 5.5 V 工作温度:-20°C ~ 70°C 安装类型:表面贴装 封装/外壳:24-BFSOP（0.295"，7.50mm 宽） 供应商设备封装:24-SOP 包装:Digi-Reel® 其它名称:MTS62C19A-HS105DKR |
| A3935KLQTR-T | 功能描述:IC CTLR MOSFET 3PH AUTO 36-SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 电机和风扇控制器，驱动器 系列:- 标准包装:1 系列:- 应用:直流电机驱动器，步进电机驱动器 评估套件:- 输出数:1 或 2 电流 - 输出:750mA 电压 - 负载:10 V ~ 40 V 电源电压:4.5 V ~ 5.5 V 工作温度:-20°C ~ 70°C 安装类型:表面贴装 封装/外壳:24-BFSOP（0.295"，7.50mm 宽） 供应商设备封装:24-SOP 包装:Digi-Reel® 其它名称:MTS62C19A-HS105DKR |
| A3936-0000T | 制造商:3M 制造商全称:3M Electronics 功能描述:100 x 100, PCB Two Row |
发布紧急采购，3分钟左右您将得到回复。