- 您现在的位置：买卖IC网 > PDF目录16645 > A3966SLBTR-T (Allegro Microsystems Inc)IC MOTOR DRIVER PWM FULL 16SOIC PDF资料下载
参数资料
| 型号： | A3966SLBTR-T |
| 厂商： | Allegro Microsystems Inc |
| 文件页数： | 7/8页 |
| 文件大小： | 0K |
| 描述： | IC MOTOR DRIVER PWM FULL 16SOIC |
| 标准包装： | 1 |
| 应用： | 步进电机驱动器，2 相 |
| 输出数： | 1 |
| 电流 - 输出： | ±650mA |
| 电压 - 负载： | 4.75 V ~ 30 V |
| 电源电压： | 4.75 V ~ 5.5 V |
| 工作温度： | -20°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SOIC（0.295"，7.50mm 宽） |
| 供应商设备封装： | 16-SOIC W |
| 包装： | 标准包装 |
| 产品目录页面： | 1140 (CN2011-ZH PDF) |
| 其它名称： | 620-1139-6 |
A3966
Dual Full-Bridge PWM Motor Driver
FUNCTIONAL DESCRIPTION (continued)
Load Current Regulation. Due to internal logic and
switching delays, t d , the actual load current peak will be
slightly higher than the I TRIP value. These delays, plus the
blanking time, limit the minimum value the current control
circuitry can regulate. To produce zero current in a wind-
ing, the ENABLE terminal should be held high, turning off
all output drivers for that full-bridge.
Logic Inputs . A logic high on the PHASE input results
in current ? owing from OUT A to OUT B of that full-bridge.
A logic low on the PHASE input results in current ? owing
from OUT B to OUT A . An internally generated dead time,
t codt , of approximately 1 μ s prevents crossover-current
spikes that can occur when switching the PHASE input.
A logic high on the ENABLE input turns off all four
output drivers of that full-bridge. This results in a fast cur-
rent decay through the internal ground clamp and ? yback
diodes. A logic low on the ENABLE input turns on the
selected source and sink driver of that full-bridge.
The ENABLE inputs can be pulse-width modulated
for applications that require a fast current-decay PWM. If
external current-sensing circuitry is used, the internal cur-
rent-control logic can be disabled by connecting the R T C T
terminal to ground.
The REFERENCE input voltage is typically set with a
resistor divider from V CC . This reference voltage is inter-
nally divided down by 4 to set up the current-comparator
trip-voltage threshold. The reference input voltage range is
0 to 2 V.
Output Drivers . To minimize on-chip power dissipa-
tion, the sink drivers incorporate a Satlington structure.
The Satlington output combines the low V CE(sat) features
of a saturated transistor and the high peak-current capabil-
ity of a Darlington (connected) transistor. A graph showing
typical output saturation voltages as a function of output
current is on page 5.
Miscellaneous Information . Thermal protection
circuitry turns off all output drivers should the junction
temperature reach 165 °C typical. This is intended only to
protect the device from failures due to excessive junction
temperatures and should not imply that output short circuits
are permitted. Normal operation is resumed when the junc-
tion temperature has decreased about 15°C.
The A3966 current control employs a ? xed-frequency,
variable duty cycle PWM technique. As a result, the cur-
rent-control regulation may become unstable if the duty
cycle exceeds 50%.
To minimize current-sensing inaccuracies caused by
ground trace I R drops, each current-sensing resistor should
have a separate return to the ground terminal of the device.
For low-value sense resistors, the I x R drops in the printed-
wiring board can be signi ? cant and should be taken into ac-
count. The use of sockets should be avoided as their contact
resistance can cause variations in the effective value of R S .
The LOAD SUPPLY terminal, V BB , should be decou-
pled with an electrolytic capacitor (47 μ F recommended)
placed as close to the device as physically practical. To
minimize the effect of system ground I x R drops on the
logic and reference input signals, the system ground should
have a low-resistance return to the load supply voltage.
The frequency of the clock oscillator will determine the
amount of ripple current. A lower frequency will result in
higher current ripple, but reduced heating in the motor and
driver IC due to a corresponding decrease in hysteretic core
losses and switching losses respectively. A higher frequen-
cy will reduce ripple current, but will increase switching
losses and EMI.
Allegro MicroSystems, LLC
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
7
相关PDF资料 |
PDF描述 |
|---|---|
| GCA31DTKD | CONN EDGECARD 62POS DIP .125 SLD |
| EBM30DTKS | CONN EDGECARD 60POS DIP .156 SLD |
| EMM11DSES | CONN EDGECARD 22POS .156 EYELET |
| A4950ELJTR-T | IC PWM MOTOR DVR FULL BRDG 8SOIC |
| RCC10DREH-S734 | CONN EDGECARD 20POS .100 EYELET |
相关代理商/技术参数 |
参数描述 |
|---|---|
| A3967 | 制造商:ALLEGRO 制造商全称:Allegro MicroSystems 功能描述:MICROSTEPPING DRIVER WITH TRANSLATOR |
| A3967SLB | 功能描述:IC MOTOR DRIVER PWM FULL 24SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 电机和风扇控制器，驱动器 系列:- 标准包装:1 系列:- 应用:直流电机驱动器，步进电机驱动器 评估套件:- 输出数:1 或 2 电流 - 输出:750mA 电压 - 负载:10 V ~ 40 V 电源电压:4.5 V ~ 5.5 V 工作温度:-20°C ~ 70°C 安装类型:表面贴装 封装/外壳:24-BFSOP（0.295"，7.50mm 宽） 供应商设备封装:24-SOP 包装:Digi-Reel® 其它名称:MTS62C19A-HS105DKR |
| A3967SLB-T | 功能描述:IC MOTOR DRIVER PWM FULL 24-SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 电机和风扇控制器，驱动器 系列:- 标准包装:1 系列:- 应用:直流电机驱动器，步进电机驱动器 评估套件:- 输出数:1 或 2 电流 - 输出:750mA 电压 - 负载:10 V ~ 40 V 电源电压:4.5 V ~ 5.5 V 工作温度:-20°C ~ 70°C 安装类型:表面贴装 封装/外壳:24-BFSOP（0.295"，7.50mm 宽） 供应商设备封装:24-SOP 包装:Digi-Reel® 其它名称:MTS62C19A-HS105DKR |
| A3967SLB-T | 制造商:Allegro MicroSystems 功能描述:Motor Controller / Driver IC |
| A3967SLBTR | 功能描述:IC MOTOR DRIVER PWM FULL 24SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 电机和风扇控制器，驱动器 系列:- 标准包装:1 系列:- 应用:直流电机驱动器，步进电机驱动器 评估套件:- 输出数:1 或 2 电流 - 输出:750mA 电压 - 负载:10 V ~ 40 V 电源电压:4.5 V ~ 5.5 V 工作温度:-20°C ~ 70°C 安装类型:表面贴装 封装/外壳:24-BFSOP（0.295"，7.50mm 宽） 供应商设备封装:24-SOP 包装:Digi-Reel® 其它名称:MTS62C19A-HS105DKR |
发布紧急采购，3分钟左右您将得到回复。