- 您现在的位置：买卖IC网 > PDF目录16472 > A3967SLB (Allegro Microsystems Inc)IC MOTOR DRIVER PWM FULL 24SOIC PDF资料下载
参数资料
| 型号： | A3967SLB |
| 厂商： | Allegro Microsystems Inc |
| 文件页数： | 5/15页 |
| 文件大小： | 0K |
| 描述： | IC MOTOR DRIVER PWM FULL 24SOIC |
| 标准包装： | 31 |
| 应用： | 步进电机驱动器 |
| 输出数： | 1 |
| 电流 - 输出： | ±750mA |
| 电压 - 负载： | 4.75 V ~ 30 V |
| 电源电压： | 3 V ~ 5.5 V |
| 工作温度： | -20°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-SOIC（0.295"，7.50mm 宽） |
| 供应商设备封装： | 24-SOIC W |
| 包装： | 管件 |
A3967
Microstepping Driver with Translator
Functional Description
Device Operation. The A3967 is a complete microstep-
ping motor driver with built in translator for easy operation
with minimal control lines. It is designed to operate bipolar
stepper motors in full-, half-, quarter- and eighth-step
modes. The current in each of the two output full bridges
is regulated with ? xed off time pulse-width modulated
(PWM) control circuitry. The full-bridge current at each
step is set by the value of an external current sense resis-
tor (R S ), a reference voltage (V REF ), and the DACs output
voltage controlled by the output of the translator.
At power up, or reset, the translator sets the DACs and
phase current polarity to initial home state (see ? gures for
home-state conditions), and sets the current regulator for
both phases to mixed-decay mode. When a step command
signal occurs on the STEP input the translator automati-
cally sequences the DACs to the next level (see table 2 for
the current level sequence and current polarity). The mic-
rostep resolution is set by inputs MS 1 and MS 2 as shown in
table 1. If the new DAC output level is lower than the pre-
vious level the decay mode for that full bridge will be set
by the PFD input (fast, slow or mixed decay). If the new
DAC level is higher or equal to the previous level then the
decay mode for that Full bridge will be slow decay. This
automatic current-decay selection will improve microstep-
ping performance by reducing the distortion of the current
waveform due to the motor BEMF.
Reset Input (RESET). The RESET input (active low)
sets the translator to a prede ? ned home state (see ? gures
for home state conditions) and turns off all of the outputs.
STEP inputs are ignored until the RESET input goes high.
Step Input (STEP). A low-to-high transition on the
STEP input sequences the translator and advances the
motor one increment. The translator controls the input to
the DACs and the direction of current ? ow in each wind-
ing. The size of the increment is determined by the state of
inputs MS 1 and MS 2 (see table 1).
Microstep Select (MS 1 and MS 2 ). Input terminals
MS1 and MS 2 select the microstepping format per
table 1. Changes to these inputs do not take effect until the
STEP command (see ? gure).
Direction Input (DIR). The state of the DIRECTION
input will determine the direction of rotation of the motor.
Internal PWM Current Control. Each full bridge is
controlled by a ? xed off-time PWM current-control cir-
cuit that limits the load current to a desired value (I TRIP ).
Initially, a diagonal pair of source and sink outputs are
enabled and current ? ows through the motor winding and
R S . When the voltage across the current-sense resistor
equals the DAC output voltage, the current-sense compara-
tor resets the PWM latch, which turns off the source driver
(slow-decay mode) or the sink and source drivers (fast- or
mixed-decay modes).
The maximum value of current limiting is set by the
selection of R S and the voltage at the V REF input with a
transconductance function approximated by:
I TRIP max = V REF /8R S
The DAC output reduces the V REF output to the cur-
rent-sense comparator in precise steps (see table 2 for %
I TRIP max at each step).
I TRIP = (% I TRIP max/100) x I TRIP max
Fixed Off-Time. The internal PWM current-control
circuitry uses a one shot to control the time the driver(s)
remain(s) off. The one shot off-time, t off , is determined by
the selection of an external resistor (R T ) and capacitor (C T )
connected from the RC timing terminal to ground. The off
time, over a range of values of C T = 470 pF to 1500 pF and
R T = 12 k Ω to 100 k Ω is approximated by:
t off = R T C T
Allegro MicroSystems, LLC
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
5
相关PDF资料 |
PDF描述 |
|---|---|
| RCM28DCMD | CONN EDGECARD 56POS .156 WW |
| M3AAA-5018R | IDC CABLE - MSC50A/MC50M/MSC50A |
| M3TKK-1040K | IDC CABLE - MSD10K/MC10F/MPK10K |
| L-14W39NKV4E | WIREWOUND INDUCTOR 39NH 0603 |
| A3966SLBTR | IC MOTOR DRIVER PWM FULL 16SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| A3967SLB-T | 功能描述:IC MOTOR DRIVER PWM FULL 24-SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 电机和风扇控制器，驱动器 系列:- 标准包装:1 系列:- 应用:直流电机驱动器，步进电机驱动器 评估套件:- 输出数:1 或 2 电流 - 输出:750mA 电压 - 负载:10 V ~ 40 V 电源电压:4.5 V ~ 5.5 V 工作温度:-20°C ~ 70°C 安装类型:表面贴装 封装/外壳:24-BFSOP（0.295"，7.50mm 宽） 供应商设备封装:24-SOP 包装:Digi-Reel® 其它名称:MTS62C19A-HS105DKR |
| A3967SLB-T | 制造商:Allegro MicroSystems 功能描述:Motor Controller / Driver IC |
| A3967SLBTR | 功能描述:IC MOTOR DRIVER PWM FULL 24SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 电机和风扇控制器，驱动器 系列:- 标准包装:1 系列:- 应用:直流电机驱动器，步进电机驱动器 评估套件:- 输出数:1 或 2 电流 - 输出:750mA 电压 - 负载:10 V ~ 40 V 电源电压:4.5 V ~ 5.5 V 工作温度:-20°C ~ 70°C 安装类型:表面贴装 封装/外壳:24-BFSOP（0.295"，7.50mm 宽） 供应商设备封装:24-SOP 包装:Digi-Reel® 其它名称:MTS62C19A-HS105DKR |
| A3967SLBTR-T | 功能描述:IC MOTOR DRIVER PWM FULL 24SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 电机和风扇控制器，驱动器 系列:- 标准包装:1 系列:- 应用:步进电机驱动器，1-2 相，2 相 评估套件:- 输出数:1 电流 - 输出:800mA 电压 - 负载:10 V ~ 28 V 电源电压:4.75 V ~ 5.25 V 工作温度:-20°C ~ 90°C 安装类型:表面贴装 封装/外壳:28-SOP + 2 翼片裸露焊盘 供应商设备封装:28-HSOPHC（15.2x7.9） 包装:剪切带 (CT) 其它名称:869-1268-1 |
| A3967SLBTR-T-CUT | 制造商:Allegro MicroSystems LLC 功能描述: |
发布紧急采购，3分钟左右您将得到回复。