- 您现在的位置：买卖IC网 > PDF目录16465 > A3982SLBTR (Allegro Microsystems Inc)IC MOTOR DRIVER STEPPER 24-SOIC PDF资料下载
参数资料
| 型号： | A3982SLBTR |
| 厂商： | Allegro Microsystems Inc |
| 文件页数： | 7/11页 |
| 文件大小： | 0K |
| 描述： | IC MOTOR DRIVER STEPPER 24-SOIC |
| 标准包装： | 1,000 |
| 应用： | 步进电机驱动器 |
| 输出数： | 1 |
| 电流 - 输出： | ±2A |
| 电压 - 负载： | 8 V ~ 35 V |
| 电源电压： | 3 V ~ 5.5 V |
| 工作温度： | -20°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-SOIC（0.295"，7.50mm 宽） |
| 供应商设备封装： | 24-SOIC W |
| 包装： | 带卷 (TR) |
A3982
DMOS Stepper Motor Driver with Translator
Functional Description
Device Operation. The A3982 is a complete stepper
motor driver with a built-in translator for easy operation
with minimal control lines. It is designed to operate bipolar
stepper motors in full- and half-step modes. The currents in
each of the two output full-bridges and all of the N-channel
DMOS FETs are regulated with fixed off-time PMW (pulse
width modulated) control circuitry. At each step, the current
for each full-bridge is set by the value of its external current-
sense resistor (R S1 or R S2 ), a reference voltage (V REF ), and
the output voltage of its DAC (which in turn is controlled by
the output of the translator).
At power-on or reset, the translator sets the DACs and the
phase current polarity to the initial Home state (shown in
figures 2 and 3), and the current regulator to Mixed Decay
Mode for both phases. When a step command signal occurs
on the STEP input, the translator automatically sequences
the DACs to the next level and current polarity. (See table 2
for the current-level sequence.) The step resolution is set by
input MS1 , as shown in table 1.
When stepping, if the new output levels of the DACs are
increment is determined by input MS1 , as shown in table 1.
Direction Input (DIR). This determines the direction of
rotation of the motor. When low, the direction will be clock-
wise and when high, counterclockwise. Changes to this input
do not take effect until the next STEP rising edge.
Internal PWM Current Control. Each full-bridge is
controlled by a fixed off-time PWM current control circuit
that limits the load current to a desired value, I TRIP . Ini-
tially, a diagonal pair of source and sink DMOS outputs are
enabled and current flows through the motor winding and
the current sense resistor, R S x . When the voltage across R S x
equals the DAC output voltage, the current sense compara-
tor resets the PWM latch. The latch then turns off either the
source DMOS FET (when in Slow Decay Mode) or the sink
and source DMOS FETs (when in Mixed Decay Mode).
The maximum value of current limiting is set by the selec-
tion of R S x and the voltage at the VREF pin. The transcon-
ductance function is approximated by the maximum value of
current limiting, I TripMAX (A), which is set by
lower than their previous output levels, then the decay mode
for the active full-bridge is set to Mixed. If the new output
I TripMAX = V REF / ( 8
? R S )
levels of the DACs are higher than or equal to their previous
levels, then the decay mode for the active full-bridge is set to
Slow. This automatic current decay selection improves step-
ping performance by reducing the distortion of the current
waveform that results from the back EMF of the motor.
RESET Input (RESET). The RESET input sets the
translator to a predefined Home state (shown in figures 2
and 3), and turns off all of the DMOS outputs. All STEP
inputs are ignored until the RESET input is set to high.
Step Input (STEP) . A low-to-high transition on the STEP
input sequences the translator and advances the motor one
increment. The translator controls the input to the DACs and
the direction of current flow in each winding. The size of the
where R S is the resistance of the sense resistor ( Ω ) and V REF
is the input voltage on the REF pin (V).
The DAC output reduces the V REF output to the current
sense comparator in precise steps, such that
I trip = (%I TripMAX / 100) × I TripMAX
(See table 2 for %I TripMAX at each step.)
It is critical that the maximum rating (0.5 V) on the SENSE1
and SENSE2 pins is not exceeded.
Fixed Off-Time. The internal PWM current control cir-
cuitry uses a one-shot circuit to control the duration of time
that the DMOS FETs remain off. The one shot off-time, t OFF ,
Allegro MicroSystems, LLC
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
7
相关PDF资料 |
PDF描述 |
|---|---|
| A3982SLB | IC MOTOR DRIVER STEPPER 24-SOIC |
| VI-J0M-EX | CONVERTER MOD DC/DC 10V 75W |
| LK2125R10K-T | INDUCTOR MULTILAYER .1UH 0805 |
| A3980KLPTR | IC DRIVER MICROSTEPPING 28-TSSOP |
| ECC25DRYH | CONN EDGECARD 50POS DIP .100 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| A3982SLBTR-T | 功能描述:IC MOTOR DRIVER STEPPER 24-SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 电机和风扇控制器，驱动器 系列:- 标准包装:1 系列:- 应用:步进电机驱动器，1-2 相，2 相 评估套件:- 输出数:1 电流 - 输出:800mA 电压 - 负载:10 V ~ 28 V 电源电压:4.75 V ~ 5.25 V 工作温度:-20°C ~ 90°C 安装类型:表面贴装 封装/外壳:28-SOP + 2 翼片裸露焊盘 供应商设备封装:28-HSOPHC（15.2x7.9） 包装:剪切带 (CT) 其它名称:869-1268-1 |
| A3983 | 制造商:ALLEGRO 制造商全称:Allegro MicroSystems 功能描述:DMOS Microstepping Driver with Translator |
| A3983_08 | 制造商:ALLEGRO 制造商全称:Allegro MicroSystems 功能描述:DMOS Microstepping Driver with Translator |
| A3983_10 | 制造商:ALLEGRO 制造商全称:Allegro MicroSystems 功能描述:The A3983 is a complete microstepping motor driver with built-in translator for easy operation. |
| A3983SLP | 功能描述:IC DRIVER MICROSTEPPING 24-TSSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 电机和风扇控制器，驱动器 系列:- 标准包装:1 系列:- 应用:直流电机驱动器，步进电机驱动器 评估套件:- 输出数:1 或 2 电流 - 输出:750mA 电压 - 负载:10 V ~ 40 V 电源电压:4.5 V ~ 5.5 V 工作温度:-20°C ~ 70°C 安装类型:表面贴装 封装/外壳:24-BFSOP（0.295"，7.50mm 宽） 供应商设备封装:24-SOP 包装:Digi-Reel® 其它名称:MTS62C19A-HS105DKR |
发布紧急采购，3分钟左右您将得到回复。