参数资料
| 型号： | A42MX16-1PQG100 |
| 厂商： | Microsemi SoC |
| 文件页数： | 52/142页 |
| 文件大小： | 0K |
| 描述： | IC FPGA MX SGL CHIP 24K 100-PQFP |
| 标准包装： | 66 |
| 系列： | MX |
| 输入/输出数： | 83 |
| 门数： | 24000 |
| 电源电压： | 3 V ~ 3.6 V，4.75 V ~ 5.25 V |
| 安装类型： | 表面贴装 |
| 工作温度： | 0°C ~ 70°C |
| 封装/外壳： | 100-BQFP |
| 供应商设备封装： | 100-PQFP（14x20） |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页当前第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页第130页第131页第132页第133页第134页第135页第136页第137页第138页第139页第140页第141页第142页
40MX and 42MX FPGA Families
Re vi s i on 11
1 - 13
Design Consideration
It is recommended to use a series 70
Ω termination resistor on every probe connector (SDI, SDO, MODE,
DCLK, PRA and PRB). The 70
Ω series termination is used to prevent data transmission corruption
during probing and reading back the checksum.
IEEE Standard 1149.1 Boundary Scan Test (BST) Circuitry
42MX24 and 42MX36 devices are compatible with IEEE Standard 1149.1 (informally known as Joint
Testing Action Group Standard or JTAG), which defines a set of hardware architecture and mechanisms
for cost-effective board-level testing. The basic MX boundary-scan logic circuit is composed of the TAP
(test access port), TAP controller, test data registers and instruction register (Figure 1-13 on page 1-14).
This circuit supports all mandatory IEEE 1149.1 instructions (EXTEST, SAMPLE/PRELOAD and
BYPASS) and some optional instructions. Table 1-3 on page 1-14 describes the ports that control JTAG
testing, while Table 1-4 on page 1-14 describes the test instructions supported by these MX devices.
Each test section is accessed through the TAP, which has four associated pins: TCK (test clock input),
TDI and TDO (test data input and output), and TMS (test mode selector).
The TAP controller is a four-bit state machine. The '1's and '0's represent the values that must be
present at TMS at a rising edge of TCK for the given state transition to occur. IR and DR indicate that the
instruction register or the data register is operating in that state.
The TAP controller receives two control inputs (TMS and TCK) and generates control and clock signals
for the rest of the test logic architecture. On power-up, the TAP controller enters the Test-Logic-Reset
state. To guarantee a reset of the controller from any of the possible states, TMS must remain high for
five TCK cycles.
42MX24 and 42MX36 devices support three types of test data registers: bypass, device identification,
and boundary scan. The bypass register is selected when no other register needs to be accessed in a
device. This speeds up test data transfer to other devices in a test data path. The 32-bit device
identification register is a shift register with four fields (lowest significant byte (LSB), ID number, part
number and version). The boundary-scan register observes and controls the state of each I/O pin.
Each I/O cell has three boundary-scan register cells, each with a serial-in, serial-out, parallel-in, and
parallel-out pin. The serial pins are used to serially connect all the boundary-scan register cells in a
device into a boundary-scan register chain, which starts at the TDI pin and ends at the TDO pin. The
Table 1-2
Device Configuration Options for Probe Capability
Security Fuse(s)
Programmed
Mode
PRA, PRB1
SDI, SDO, DCLK1
No
LOW
User I/Os2
No
HIGH
Probe Circuit Outputs
Probe Circuit Inputs
Yes
–
Probe Circuit Secured
Notes:
1. Avoid using SDI, SDO, DCLK, PRA and PRB pins as input or bidirectional ports. Since these pins are
active during probing, input signals will not pass through these pins and may cause contention.
2. If no user signal is assigned to these pins, they will behave as unused I/Os in this mode. See the "Pin
Descriptions" section on page 1-83 for information on unused I/O pins.
相关PDF资料 |
PDF描述 |
|---|---|
| A42MX16-PQG100I | IC FPGA MX SGL CHIP 24K 100-PQFP |
| RSM43DRMD | CONN EDGECARD 86POS .156 WW |
| ABC43DRYS-S93 | CONN EDGECARD 86POS DIP .100 SLD |
| HMM43DRXN | CONN EDGECARD 86POS DIP .156 SLD |
| FMM18DSES | CONN EDGECARD 36POS .156 EYELET |
相关代理商/技术参数 |
参数描述 |
|---|---|
| A42MX16-1PQG100I | 功能描述:IC FPGA MX SGL CHIP 24K 100-PQFP RoHS:是 类别:集成电路 (IC) >> 嵌入式 - FPGA（现场可编程门阵列） 系列:MX 标准包装:40 系列:SX-A LAB/CLB数:6036 逻辑元件/单元数:- RAM 位总计:- 输入/输出数:360 门数:108000 电源电压:2.25 V ~ 5.25 V 安装类型:表面贴装 工作温度:0°C ~ 70°C 封装/外壳:484-BGA 供应商设备封装:484-FPBGA（27X27） |
| A42MX16-1PQG100M | 制造商:Microsemi Corporation 功能描述:FPGA 24K GATES 608 CELLS 119MHZ/198MHZ 0.45UM 3.3V/5V 100PQF - Trays 制造商:Microsemi Corporation 功能描述:IC FPGA MX SGL CHIP 24K 100-PQFP 制造商:Microsemi Corporation 功能描述:IC FPGA 83 I/O 100PQFP |
| A42MX16-1PQG160 | 功能描述:IC FPGA MX SGL CHIP 24K 160-PQFP RoHS:是 类别:集成电路 (IC) >> 嵌入式 - FPGA（现场可编程门阵列） 系列:MX 标准包装:40 系列:SX-A LAB/CLB数:6036 逻辑元件/单元数:- RAM 位总计:- 输入/输出数:360 门数:108000 电源电压:2.25 V ~ 5.25 V 安装类型:表面贴装 工作温度:0°C ~ 70°C 封装/外壳:484-BGA 供应商设备封装:484-FPBGA（27X27） |
| A42MX16-1PQG160I | 功能描述:IC FPGA MX SGL CHIP 24K 160-PQFP RoHS:是 类别:集成电路 (IC) >> 嵌入式 - FPGA（现场可编程门阵列） 系列:MX 标准包装:40 系列:SX-A LAB/CLB数:6036 逻辑元件/单元数:- RAM 位总计:- 输入/输出数:360 门数:108000 电源电压:2.25 V ~ 5.25 V 安装类型:表面贴装 工作温度:0°C ~ 70°C 封装/外壳:484-BGA 供应商设备封装:484-FPBGA（27X27） |
| A42MX16-1PQG160M | 制造商:Microsemi Corporation 功能描述:FPGA 24K GATES 608 CELLS 119MHZ/198MHZ 0.45UM 3.3V/5V 160PQF - Trays 制造商:Microsemi Corporation 功能描述:IC FPGA 125 I/O 160PQFP |
发布紧急采购，3分钟左右您将得到回复。