参数资料
型号: A4970SLBTR-T
厂商: Allegro Microsystems Inc
文件页数: 5/9页
文件大小: 0K
描述: IC PWM MOTOR DVR FULL 24-SOICW
特色产品: A4970 Motor Driver IC
标准包装: 1
应用: 直流电机驱动器,PWM 电机驱动器,步进电机驱动器
输出数: 1 或 2
电流 - 输出: 750mA
电压 - 负载: 7.45 V ~ 45 V
电源电压: 4.75 V ~ 5.25 V
工作温度: -20°C ~ 85°C
安装类型: 表面贴装
封装/外壳: 24-SOIC(0.295",7.50mm 宽)
供应商设备封装: 24-SOIC W
包装: 标准包装
其它名称: 620-1437-6
A4970
Dual Full-Bridge Motor Driver
APPLICATIONS INFORMATION
PWM CURRENT CONTROL
The A4970 dual bridges drive both windings of a bipolar stepper
motor. Output current is sensed and controlled independently
in each bridge by an external sense resistor, R S , internal
comparator, and monostable multivibrator.
When the bridge is turned on, current increases in the motor
winding and it is sensed by the external sense resistor until the
sense voltage, V SENSE , reaches the level set at the comparator
input:
I TRIP = V REF /10 R S
The comparator then triggers the monostable, which turns off
the source driver of the bridge.
The actual load current peak will be slightly higher than the
trip point (especially for low-inductance loads) because of the
internal logic and switching delays. This delay, t d , is typically 2
μ s. After turn-off, the motor current decays, circulating through
the ground-clamp diode and sink transistor. The source driver
off-time (and therefore the magnitude of the current decrease)
This equation assumes that the current control loop duty cycle
is greater than 5% and the voltage on the SENSE pin will reach
99% of the target value set for V SENSE . These assumptions will
apply to the majority of applications and can be regarded as a
starting value for further optimization by calculation or waveform
measurement.
Depending on load type, many applications will not require these
external components (SENSE connected to E).
PWM OUTPUT CURRENT WAVE FORM
V P HAS E
+
is determined by the external RC timing components of the
monostable:
I OUT
0
where:
t off = R T C T
I T R IP
R T = 20 to 100 k Ω , and
C T = 100 to 1000 pF.
t d
t off
Dwg. WM-003-1A
The ? xed off-time should be short enough to keep the current
BB
chopping above the audible range (< 46 μ s) and long enough to
properly regulate the current. Because only slow-decay current
control is available, short off times (< 10 μ s) require additional
efforts to ensure proper current regulation. Factors that can
negatively affect the ability to properly regulate the current when
using short off times include: higher motor-supply voltage, light
load, and longer than necessary blank time.
When the source driver is re-enabled, the winding current (the
sense voltage) is again allowed to rise to the comparator ’s
threshold. This cycle repeats itself, maintaining the average
motor winding current at the desired level.
Loads with high distributed capacitances may result in high turn-
on current peaks. This peak (appearing across R S ) will attempt
to trip the comparator, resulting in erroneous current control or
high-frequency oscillations. An external R C C C time delay should
be used to further delay the action of the comparator.
The time constant for the delay to produce suitable blank time can
be estimated using:
R C C C = 0.0114 × R T C T
LOAD CURRENT PATHS
V
RS
Bridge On
Source Off, Slow Decay
All Off, Fast Decay
Allegro MicroSystems, LLC
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
5
相关PDF资料
PDF描述
A4973SLBTR-T IC PWM MOTOR DVR FULL 16SOIC
A4975SB-T IC PWM MICROSTEP DVR FULL 16DIP
A4979GLPTR-T IC MOTOR DRVR MICRO STEP 28TSSOP
A4980KLPTR-T IC STEPPER DVR PROGR 28-TSSOP
A4982SLPTR-T IC DRIVER MICROSTEPPING 24-TSSOP
相关代理商/技术参数
参数描述
A49721-000 制造商:TE Connectivity 功能描述:Shrink Boot Adapters 90 制造商:TE Connectivity 功能描述:HEX40-AB-90-15-A5-3 - Bulk
A4972-6-02 制造商:Esna Technologies 功能描述:
A4973 制造商:ALLEGRO 制造商全称:Allegro MicroSystems 功能描述:Full-Bridge PWM Motor Driver
A497-3982-01 制造商:Bel Fuse 功能描述: 制造商:BELFUSE 功能描述:
A4973SB-T 功能描述:IC PWM MOTOR DVR FULL 16DIP RoHS:是 类别:集成电路 (IC) >> PMIC - 电机和风扇控制器,驱动器 系列:- 标准包装:1 系列:- 应用:步进电机驱动器,1-2 相,2 相 评估套件:- 输出数:1 电流 - 输出:800mA 电压 - 负载:10 V ~ 28 V 电源电压:4.75 V ~ 5.25 V 工作温度:-20°C ~ 90°C 安装类型:表面贴装 封装/外壳:28-SOP + 2 翼片裸露焊盘 供应商设备封装:28-HSOPHC(15.2x7.9) 包装:剪切带 (CT) 其它名称:869-1268-1