- 您现在的位置：买卖IC网 > PDF目录16634 > A4973SB-T (Allegro Microsystems Inc)IC PWM MOTOR DVR FULL 16DIP PDF资料下载
参数资料
| 型号： | A4973SB-T |
| 厂商： | Allegro Microsystems Inc |
| 文件页数： | 6/11页 |
| 文件大小： | 0K |
| 描述： | IC PWM MOTOR DVR FULL 16DIP |
| 特色产品： | A4973 Motor Driver |
| 标准包装： | 7,500 |
| 应用： | 直流电机驱动器，PWM 电机驱动器 |
| 输出数： | 1 |
| 电流 - 输出： | 1.5A |
| 电压 - 负载： | 5 V ~ 50 V |
| 电源电压： | 3 V ~ 5.5 V |
| 工作温度： | -20°C ~ 85°C |
| 安装类型： | 通孔 |
| 封装/外壳： | 16-DIP（0.300"，7.62mm） |
| 供应商设备封装： | 16-DIP |
| 包装： | 管件 |
| 其它名称： | 620-1434-5 A4973SB-T-ND |
1.05 × (t ON(min) max + t OFF ) × R LOAD
A4973
The operation of the circuit is as follows: when the PWM latch is
reset by the current comparator, the voltage on the RC terminal
will begin to decay from approximately 0.60V CC . When the
voltage on the RC terminal reaches approximately 0.22V CC , the
PWM latch is set, thereby enabling the driver(s).
RC Blanking. In addition to determining the fixed off-time of
the PWM control circuit, the C T component sets the comparator
blanking time. This function blanks the output of the comparator
when the outputs are switched by the internal current-control
circuitry (or by the PHASE, BRAKE, or ENABLE inputs).
The comparator output is blanked to prevent false over-current
detections due to reverse recovery currents of the clamp diodes,
and/or switching transients related to distributed capacitance in
the load.
During internal PWM operation, at the end of the t OFF time, the
comparator ’s output is blanked and C T begins to be charged
from approximately 0.22V CC by an internal current source of
approximately 1 mA. The comparator output remains blanked
until the voltage on C T reaches approximately 0.60V CC .
When a transition of the PHASE input occurs, C T is discharged
to near ground during the crossover delay time (the crossover
delay time is present to prevent simultaneous conduction of
the source and sink drivers). After the crossover delay, C T is
charged by an internal current source of approximately 1 mA.
The comparator output remains blanked until the voltage on C T
reaches approximately 0.60V CC .
When the device is disabled, via the ENABLE input, C T is
discharged to near ground. When the device is re-enabled, C T is
charged by an internal current source of approximately 1 mA.
The comparator output remains blanked until the voltage on C T
reaches approximately 0.60V CC .
For 3.3 V operation, the minimum recommended value
for C T is 680 pF ± 5 %. For 5.0 V operation, the minimum
recommended value for C T is 470 pF ± 5%. These values
ensure that the blanking time is sufficient to avoid false trips
of the comparator under normal operating conditions. For
optimal regulation of the load current, the above values for C T
are recommended and the value of R T can be sized to determine
t OFF . For more information regarding load current regulation, see
below.
Full-Bridge PWM Motor Driver
LOAD CURRENT REGULATION
WITH INTERNAL PWM
CURRENT-CONTROL CIRCUITRY
When the device is operating in slow current-decay mode,
there is a limit to the lowest level that the PWM current-
control circuitry can regulate load current. The limitation is the
minimum duty cycle, which is a function of the user-selected
value of t OFF and the minimum on-time pulse t ON(min) max that
occurs each time the PWM latch is reset. If the motor is not
rotating (as in the case of a stepper motor in hold/detent mode, a
brush dc motor when stalled, or at startup), the worst case value
of current regulation can be approximated by:
{ [ V BB – (2 × I × R DS ) ] × t ON(min) max } – [1.05 (I × R DS + V F ) × t OFF ]
I AVE ≈
where t OFF = R T x C T , R LOAD is the series resistance of the load,
V BB is the motor supply voltage and t ON(min) max is specified in
the Electrical Characteristics table. When the motor is rotating,
the back EMF generated will influence the above relationship.
For brush dc motor applications, the current regulation is
improved. For stepper motor applications, when the motor is
rotating, the effect is more complex. A discussion of this subject
is included in the section on stepper motors below.
The following procedure can be used to evaluate the worst-case
slow current-decay internal PWM load current regulation in the
system:
1. Set V REF to 0 volts. With the load connected and the PWM
current control operating in slow current-decay mode, use an
oscilloscope to measure the time the output is low (sink on) for
the output that is chopping. This is the typical minimum on time
(t ON(min) typ) for the device.
2. The C T then should be increased until the measured value
of t ON(min) is equal to t ON(min) max as specified in the electrical
characteristics table.
3. When the new value of C T has been set, the value of R T should
be decreased so the value for t OFF = R T x C T (with the artificially
increased value of C T ) is equal to the nominal design value.
4. The worst-case load-current regulation then can be measured
in the system under operating conditions.
Allegro MicroSystems, LLC
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
6
相关PDF资料 |
PDF描述 |
|---|---|
| MC33910BACR2 | IC SYSTEM BASIS CHIP 32LQFP |
| VE-B5V-EW | CONVERTER MOD DC/DC 5.8V 100W |
| VE-B40-EW | CONVERTER MOD DC/DC 5V 100W |
| A2MXS-3436G | ADM34S/AE34G/X |
| MC34910G5ACR2 | IC SYSTEM BASIS CHIP LIN 32-LQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| A4973SLBTR-T | 功能描述:IC PWM MOTOR DVR FULL 16SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 电机和风扇控制器，驱动器 系列:- 产品变化通告:ATA683(3,4)PLQW Obsolescence 09/Aug/2012 标准包装:1 系列:- 应用:DC 电机控制器，无刷（BLDC），3 相 评估套件:可供 输出数:1 电流 - 输出:100mA 电压 - 负载:5.25 V ~ 20 V 电源电压:5.25 V ~ 20 V 工作温度:-40°C ~ 150°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-VQFN（7x7） 包装:剪切带 (CT) 其它名称:ATA6833-PLQWCT |
| A4975 | 制造商:ALLEGRO 制造商全称:Allegro MicroSystems 功能描述:Full-Bridge PWM Microstepping Motor Driver |
| A4975SB-T | 功能描述:IC PWM MICROSTEP DVR FULL 16DIP RoHS:是 类别:集成电路 (IC) >> PMIC - 电机和风扇控制器，驱动器 系列:- 标准包装:1 系列:- 应用:直流电机驱动器，步进电机驱动器 评估套件:- 输出数:1 或 2 电流 - 输出:750mA 电压 - 负载:10 V ~ 40 V 电源电压:4.5 V ~ 5.5 V 工作温度:-20°C ~ 70°C 安装类型:表面贴装 封装/外壳:24-BFSOP（0.295"，7.50mm 宽） 供应商设备封装:24-SOP 包装:Digi-Reel® 其它名称:MTS62C19A-HS105DKR |
| A4975SLBTR-T | 功能描述:IC PWM MICROSTEP DVR FULL 16SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 电机和风扇控制器，驱动器 系列:- 产品变化通告:ATA683(3,4)PLQW Obsolescence 09/Aug/2012 标准包装:1 系列:- 应用:DC 电机控制器，无刷（BLDC），3 相 评估套件:可供 输出数:1 电流 - 输出:100mA 电压 - 负载:5.25 V ~ 20 V 电源电压:5.25 V ~ 20 V 工作温度:-40°C ~ 150°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-VQFN（7x7） 包装:剪切带 (CT) 其它名称:ATA6833-PLQWCT |
| A4979 | 制造商:ALLEGRO 制造商全称:Allegro MicroSystems 功能描述:The A4979 is a flexible microstepping motor driver with built-in translator for easy operation. |
发布紧急采购，3分钟左右您将得到回复。