- 您现在的位置：买卖IC网 > PDF目录1888 > A5358CLWTR-T (Allegro Microsystems Inc)IC SMOKE DETECTOR PHOTO 16-SOIC PDF资料下载
参数资料
| 型号： | A5358CLWTR-T |
| 厂商： | Allegro Microsystems Inc |
| 文件页数： | 11/13页 |
| 文件大小： | 0K |
| 描述： | IC SMOKE DETECTOR PHOTO 16-SOIC |
| 标准包装： | 3,000 |
| 类型： | 烟雾探测器 |
| 输入类型： | 光电 |
| 输出类型： | 电压 |
| 电流 - 电源： | 12µA |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SOIC（0.295"，7.50mm 宽） |
| 供应商设备封装： | 16-SOIC W |
| 包装： | 带卷 (TR) |
Photoelectric Smoke Detector
with Interconnect and Timer
A5358
7
Allegro MicroSystems, LLC
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
Pin and Circuit Description
(In Typical Application)
C1 Pin
A capacitor connected to this pin determines the gain, Ae, of
the photoamplifier during the push-to-test mode and during the
chamber monitor test. A typical capacitor value for this high-
gain (supervisory) mode is 0.047 μF, but it should be selected
based on the photochamber background reflections reaching the
detector and the desired level of sensitivity. Ae = 1 + (C1/ 10),
where C1 is in pF. Ae should not exceed 10,000 and thus C1
should not exceed 0.1 μF. Coupling of other signals to the C1,
C2, and DETECT inputs must be minimized.
C2 Pin
A capacitor connected to this pin determines the gain, Ae, of
the photoamplifier during standby. A typical capacitor value for
this low-gain mode is 4700 pF, but it should be selected based
on a specific photochamber and the desired level of sensitiv-
ity to smoke. Ae = 1 + (C2/ 10), where C2 is in pF. Ae should not
exceed 10,000 and thus C2 should not exceed 0.1 μF. This gain
increases by a nominal 10% after a local alarm is detected (three
consecutive detections). A resistor must be installed in series
with the C2 capacitor.
DETECT Pin
This is the input to the photoamplifier and is connected to the
cathode of the photodiode. The photodiode is operated at zero
bias and should have low dark leakage current and low capaci-
tance. A shunt resistor must be installed in parallel with the
photodiode.
STROBE Pin
This output provides a strobed, regulated voltage of VDD – 5 V.
The minus side of all internal and external photoamplifier cir-
cuitry is referenced to this pin.
VDD Pin
This pin is connected to the positive supply potential and can
range from 6 to 12 V with respect to VSS.
IRED Pin
This output provides a pulsed base current for the external NPN
transistor, which drives the IR emitter. Its beta should be greater
than 100. To minimize noise impact, the IRED output is not
active when the horn and visible LED outputs are active.
I/O Pin
A connection at this pin allows multiple smoke detectors to be
interconnected. If any single unit detects smoke, its I/O pin is
driven high, and all connected units will sound their associated
horns.
As an input, the I/O is sampled every fourth clock cycle (nomi-
nally 42 ms). When the I/O pin is driven high by another device,
three consecutive samples with I/O high plus one additional
cycle (nominally 10.5 ms) are required to cause an alarm. If the
I/O falls below its threshold at any time during those (nomi-
nally) 95 ms, an internal latch is reset and there will not be an
alarm. Thus, depending on when during the (nominally) 42 ms
sample cycle I/O is initially forced high, the I/O must remain
high for a minimum of (nominally) 95 to 137 ms to cause an
alarm. This filtering provides significant immunity to I/O noise.
The LED is suppressed when an alarm is signaled from an
interconnected unit, and any local alarm condition causes this
pin to be ignored as an input. This pin has an on-chip pull-down
device and must be left unconnected if not used. In the applica-
tion, there should be a series current-limiting resistor to other
smoke alarms.
HORN1, HORN2, and FEEDBACK Pins
These three pins are used with a self-resonating piezoelectric
transducer and horn-starting external passive components. The
output HORN1 is connected to the piezo metal support elec-
trode. The complementary output, HORN2, is connected to the
ceramic electrode. The FEEDBACK input is connected to the
feedback electrode. If the FEEDBACK pin is not used, it must
be connected to VSS.
LED Pin
This open-drain NMOS output is used to directly drive a visible
LED. The load for the low-battery test is applied to this output.
If an LED is not used, it should be replaced with an equivalent
resistor (typically 500 to 1000 Ω) such that the battery load-
ing remains about 10 mA. The low-battery test does not occur
coincident with any other test or alarm signal. The LED also
indicates detector status as follows (with component values as in
the typical application, all times nominal):
Condition
Pulse Occurrence
Standby
Every 43 s
Local Smoke
Every 0.67 s
Remote Alarm
No pulses
Test Mode
Every 0.67 s
Timer Mode
Every 10 s
相关PDF资料 |
PDF描述 |
|---|---|
| A5366CLWTR-T | IC SMOKE DETECTOR PHOTO 16-SOIC |
| A5367CA-T | IC SMOKE DETECTOR ION 16-DIP |
| A54SX32-1CQ256B | IC FPGA SX 48K GATES 256-CQFP |
| A54SX72A-1CQ256B | IC FPGA SX-A 108K 256-CQFP |
| A6850KLTR-T | IC SWITCH INTERFACE 2CHAN 8-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| A5361041420000 | 制造商: 功能描述: 制造商:undefined 功能描述: |
| A53627-000 | 制造商:TE Connectivity 功能描述:Labels Dot Matrix Printable Label Polyester White 6.4x6.4mm 制造商:TE Connectivity 功能描述:E-064064-10-9 - Bag 制造商:TE Connectivity 功能描述:LABEL ID PRODUCT |
| A53640PC4 | 制造商:TE Connectivity 功能描述: |
| A5364CA | 功能描述:IC SMOKE DETECTOR ION 16-DIP RoHS:否 类别:集成电路 (IC) >> 接口 - 传感器和探测器接口 系列:- 其它有关文件:Automotive Product Guide 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:74 系列:- 类型:触控式传感器 输入类型:数字 输出类型:数字 接口:JTAG，串行 电流 - 电源:100µA 安装类型:表面贴装 封装/外壳:20-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:20-TSSOP 包装:管件 |
| A5364CA-T | 功能描述:IC SMOKE DETECTOR ION 16-DIP RoHS:是 类别:集成电路 (IC) >> 接口 - 传感器和探测器接口 系列:- 其它有关文件:Automotive Product Guide 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:74 系列:- 类型:触控式传感器 输入类型:数字 输出类型:数字 接口:JTAG，串行 电流 - 电源:100µA 安装类型:表面贴装 封装/外壳:20-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:20-TSSOP 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。