- 您现在的位置：买卖IC网 > Datasheet目录306 > A6261KLPTR-T (Allegro Microsystems Inc)IC LED ARRAY DVR 400MA 16-TSSOP Datasheet资料下载
参数资料
| 型号： | A6261KLPTR-T |
| 厂商： | Allegro Microsystems Inc |
| 文件页数： | 6/19页 |
| 文件大小： | 0K |
| 描述： | IC LED ARRAY DVR 400MA 16-TSSOP |
| 标准包装： | 1 |
| 恒定电流： | 是 |
| 拓扑： | 线性（LDO），PWM |
| 输出数： | 4 |
| 内部驱动器： | 是 |
| 类型 - 主要： | 车载 |
| 类型 - 次要： | 高亮度 LED（HBLED） |
| 电源电压： | 6 V ~ 50 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-TSSOP（0.173"，4.40mm）裸露焊盘 |
| 供应商设备封装： | 16-TSSOP-EP |
| 包装： | 标准包装 |
| 工作温度： | -40°C ~ 125°C |
| 其它名称： | 620-1360-6 |
A6261
Protected LED Array Driver
Functional Description
(1)
I REF =
I LAx = G Hx × I REF
TheA6261 is a linear current regulator that is designed to provide
drive current and protection for parallel strings of series-con-
nected high brightness LEDs. The LP and LY options provide up
to four matched programmable current outputs, at up to 100 mA,
whereas the LJ option provides two outputs, LA1 = 200 mA and
LA2 = 100 mA. All the outputs have low minimum dropout volt-
ages below the main supply voltage. For 12 V power net applica-
tions, optimum performance is achieved when driving all strings
of 1 to 3 series connected LEDs, at rated current per string.
The A6261 is specifically designed for use in applications where
the LED current is controlled by a single logic input or a high-
side switched supply. In addition the A6261 disables all LEDs on
detecting a single open LED.
Current regulation is maintained and the LEDs protected during a
short-to-ground at any point in the LED string. A short-to-ground
on any regulator output terminal will disable that output and set
the fault flag. An open load on any output will set the fault flag
and disable all outputs. Remaining outputs can be re-enabled
by pulling the fault flag output low. Individual outputs can be
disabled by connecting the output to VIN.
Integrated thermal management reduces the regulated current
level at high internal junction temperatures to limit power dis-
sipation.
Pin Functions
LA[1:4] Current source connected to the anode of the first
LED in each string. Connect directly to VIN to disable the
respective output. In this document “LAx” indicates any one
output of the ICs.
FF Open drain fault flag, used with an external pull-up resistor,
to indicate open, short, or overtemperature conditions. FF is inac-
tive when a fault is present. During an open load condition, FF
can be pulled low to force the remaining outputs on.
LED Current Level
The LED current is controlled by four matching linear current
regulators between the VIN pin and each of the LAx outputs. The
basic equation that determines the nominal output current at each
LAx pin is:
Given EN = high,
1.2
R REF
and
(2)
where I LAx is in mA and R REF is in k Ω .
The output current may be reduced from the set level by the ther-
mal monitor circuit.
Conversely the reference resistors may be calculated from:
VIN Supply to the control circuit and current regulators. A small
value ceramic bypass capacitor, typically 100 nF, should be con-
nected from close to this pin to the GND pin.
R REF =
1.2 × G Hx
I LAx
(3)
R REF = = 167 Ω
GND Ground reference connection. Should be connected directly
to the negative supply.
EN Logic input to enable LED current output. This provides a
direct on/off action and can be used for direct PWM control.
IREF 1.2 V reference to set current reference. Connect resistor,
R REF , to GND to set reference current.
THTH Sets the thermal monitor threshold, T JM , where the output
current starts to reduce with increasing temperature. Connecting
THTH directly to GND will disable the thermal monitor function.
where I LAx is in mA and R REF is in k Ω .
For example, where the required current is 90 mA in LA2 the
resistor value will be :
15
90
These equations completely define the output currents with
respect to the setting resistors. However, for further reference, a
more detailed description of the internal reference current calcu-
lations is included below.
Allegro MicroSystems, LLC
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
6
相关PDF资料 |
PDF描述 |
|---|---|
| A6262KLPTR-T | IC LED ARRAY DRIVER AUTO 16TSSOP |
| A6264KLPTR-T | IC LED DVR STOP/TAIL 16-TSSOP |
| A6265KLPTR-T | IC LED CTLR HI CURRENT 16-TSSOP |
| A6266KLPTR-T | IC LED CTLR AUTO HI CURR 16TSSOP |
| A6267KLPTR-T | IC LED CTLR AUTO HI CURR 16TSSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| A6261KLYTR-T | 功能描述:IC LED ARRAY DVR 400MA 10-MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 特色产品:LM3445 TRIAC Dimmable LED Driver 标准包装:55 系列:PowerWise® 恒定电流:是 恒定电压:- 拓扑:PWM，降压（降压） 输出数:1 内部驱动器:无 类型 - 主要:- 类型 - 次要:高亮度 LED（HBLED） 频率:30kHz ~ 1MHz 电源电压:8 V ~ 12 V 输出电压:- 安装类型:表面贴装 封装/外壳:14-SOIC（0.154"，3.90mm 宽） 供应商设备封装:14-SOICN 包装:管件 工作温度:-40°C ~ 125°C 产品目录页面:1285 (CN2011-ZH PDF) 其它名称:LM3445M |
| A6262 | 制造商:ALLEGRO 制造商全称:Allegro MicroSystems 功能描述:The A6262 is a linear, programmable current regulator providing up to 100 mA from each of four outputs to drive arrays of high brightness LEDs. |
| A6262KLPTR-T | 功能描述:IC LED ARRAY DRIVER AUTO 16TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 恒定电流:- 恒定电压:- 拓扑:升压（升压），切换式电容器（充电泵） 输出数:1 内部驱动器:是 类型 - 主要:背光 类型 - 次要:白色 LED 频率:625kHz ~ 875kHz 电源电压:2.7 V ~ 5.3 V 输出电压:5V 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-µMAX 包装:带卷 (TR) 工作温度:-40°C ~ 85°C |
| A6262KLYTR-T | 功能描述:IC LED ARRAY DRIVER AUTO 10-MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 特色产品:LM3445 TRIAC Dimmable LED Driver 标准包装:55 系列:PowerWise® 恒定电流:是 恒定电压:- 拓扑:PWM，降压（降压） 输出数:1 内部驱动器:无 类型 - 主要:- 类型 - 次要:高亮度 LED（HBLED） 频率:30kHz ~ 1MHz 电源电压:8 V ~ 12 V 输出电压:- 安装类型:表面贴装 封装/外壳:14-SOIC（0.154"，3.90mm 宽） 供应商设备封装:14-SOICN 包装:管件 工作温度:-40°C ~ 125°C 产品目录页面:1285 (CN2011-ZH PDF) 其它名称:LM3445M |
| A6263 | 制造商:ALLEGRO 制造商全称:Allegro MicroSystems 功能描述:Protected LED Array Driver |
发布紧急采购，3分钟左右您将得到回复。