- 您现在的位置：买卖IC网 > Datasheet目录306 > A6267KLPTR-T (Allegro Microsystems Inc)IC LED CTLR AUTO HI CURR 16TSSOP Datasheet资料下载
参数资料
| 型号： | A6267KLPTR-T |
| 厂商： | Allegro Microsystems Inc |
| 文件页数： | 14/17页 |
| 文件大小： | 0K |
| 描述： | IC LED CTLR AUTO HI CURR 16TSSOP |
| 标准包装： | 8,000 |
| 恒定电流： | 是 |
| 拓扑： | 低端，PWM，降压（降压），升压（升压） |
| 输出数： | 1 |
| 内部驱动器： | 无 |
| 类型 - 主要： | 车载，背光 |
| 频率： | 100kHz ~ 700kHz |
| 电源电压： | 6.5 V ~ 50 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-TSSOP（0.173"，4.40mm）裸露焊盘 |
| 供应商设备封装： | 16-TSSOP-EP |
| 包装： | 带卷 (TR) |
| 工作温度： | -40°C ~ 150°C |
A6267
Automotive High Current LED Controller
levels usually defined, the smallest value being the figure to work
with:
? Saturation level, where the inductance value typically drops by
10%, or
? Temperature rise, where the part experiences a certain rise in
temperature at full rated current. This parameter can be defined
between a 20°C and 50°C rise in temperature. It is important to
understand how manufacturers define the maximum operating
temperature, because this can often incorporate the self-heating
temperature rise.
In most cases the limiting current is usually the saturation value.
To improve efficiency, the inductor should also have low winding
resistance, typically < 50 m Ω , and the core material will usually
be ferrite, with low losses at the oscillator frequency.
Recommended inductor manufacturers/series are:
? Coilcraft/ MSS1278T
? TDK/ SLF12575 type H
Diode The diode should have a low forward voltage, to reduce
conduction losses, and a low capacitance, to reduce switching
losses. Schottky diodes can provide both these features if care-
fully selected. The forward voltage drop is a natural advantage
for Schottky diodes and reduces as the current rating increases.
However, as the current rating increases, the diode capacitance
also increases so the optimum selection is usually the lowest cur-
rent rating above the required maximum, in this case I L(PK) .
Switch Current Sense Resistor (RSS) Neither the absolute
value of the switch current nor the accuracy of the measurement
is important, because the regulator will continuously adjust the
switch current, within a closed loop, to provide sufficient energy
for the output. For maximum accuracy the switch sense resistor
value should be chosen to maximize the differential signal seen
by the sense amplifier. The input limit of the sense amplifier,
V IDS , and the maximum switch current, I S (max), therefore define
the maximum value of the sense resistor as:
switch current control is within a closed loop, it is possible to
reduce the value of the sense resistor to reduce its power dissipa-
tion. However this will reduce the accuracy of the regulated LED
current.
In Boost mode, the power loss in the switch sense resistor is
worse at the lowest input voltage:
P LOSS = ( V LED [ V LED – V IN (min)] / V IN (min) 2 ) × R SS × I 2LED (23)
In Buck Boost mode, the power loss in the switch sense resistor
is worse at the lowest input voltage:
P LOSS = ( V LED / V IN (min))( V LED + V IN (min)) × R SS × I 2LED (24)
External Switch MOSFET A logic-level N-channel MOSFET
is used as the switch for the DC-to-DC converter. In the boost
configuration the voltage at the drain of the MOSFET is equal
to the maximum voltage across the string of LEDs. In the
buck-boost configuration the output voltage is referenced to
the positive supply. This means that the voltage at the drain of
the MOSFET will reach a voltage equal to the sum of the LED
voltage and the supply voltage. Under load dump conditions,
up to 90 V may be present on this node. In this case the external
MOSFET should therefore be rated at greater than 100 V.
The peak switch current is defined by the maximum inductor cur-
rent, I L(PK) . However in most cases the MOSFET will be chosen
by selecting low on-resistance, which usually results in a current
rating of several times the required peak current.
In addition to minimizing cost, the choice of MOSFET should
consider both the on-resistance and the total gate charge. The
total gate charge will determine the average current required from
the internal regulator and thus the power dissipation.
Output Capacitor There are several points to consider when
selecting the output capacitor.
Unlike some switch-mode regulators, the value of the output
capacitor in this case is not critical for output stability. The
R SS = V IDS / I S (max)
(22)
capacitor value is only limited by the required maximum ripple
voltage.
Where I S (max) is the maximum switch current and should be set
above the maximum inductor current, I L(PK) .
This represents the maximum measurable value of the switch
(and inductor) current; however, the peak switch current will
always be less than this, set by the control circuit, depending on
the input voltage and the required load conditions. Because the
Due to the switching topology used, the ripple current for this
circuit is high because the output capacitor provides the LED
current when the switch is active. The capacitor is then recharged
each time the inductor passes energy to the output. The ripple
current on the output capacitor will be equal to the peak inductor
current.
Allegro MicroSystems, LLC
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
14
相关PDF资料 |
PDF描述 |
|---|---|
| A6268KLPTR-T | IC LED CTLR AUTOMOBILE 16TSSOP |
| A6280EA-T | IC LED DRIVER PWM CONTROL 16-DIP |
| A6281EESTR-T | IC LED DRIVER PWM CONTROL 16-QFN |
| A6282ELPTR-T | IC LED DRIVER LINEAR 24-TSSOP |
| A8431EEHTR-T | IC LED DRVR WHITE BCKLGHT 6-MLP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| A6268 | 制造商:ALLEGRO 制造商全称:Allegro MicroSystems 功能描述:The A6268 is a DC-to-DC converter controller, providing a programmable constant current output for driving high power LEDs in series. |
| A6268KLPTR-T | 功能描述:IC LED CTLR AUTOMOBILE 16TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 恒定电流:- 恒定电压:- 拓扑:升压（升压），切换式电容器（充电泵） 输出数:1 内部驱动器:是 类型 - 主要:背光 类型 - 次要:白色 LED 频率:625kHz ~ 875kHz 电源电压:2.7 V ~ 5.3 V 输出电压:5V 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-µMAX 包装:带卷 (TR) 工作温度:-40°C ~ 85°C |
| A6269 | 制造商:ALLEGRO 制造商全称:Allegro MicroSystems 功能描述:Automotive LED Array Driver |
| A6269KLJTR-T | 制造商:Allegro MicroSystems 功能描述:TWO CHANNEL LINEAR LED DRIVER 制造商:ALLEGRO MICROSYSTEMS, LLC 功能描述:IC LED DRVR AUTOMOTIVE 8SOICN |
| A626A | 功能描述:ADAPTER PROGRAMMER 32-SSOP RoHS:否 类别:编程器，开发系统 >> 过时/停产零件编号 系列:- 标准包装:1 系列:- 类型:MCU 适用于相关产品:Freescale MC68HC908LJ/LK（80-QFP ZIF 插口） 所含物品:面板、缆线、软件、数据表和用户手册 其它名称:520-1035 |
发布紧急采购，3分钟左右您将得到回复。