- 您现在的位置：买卖IC网 > PDF目录364585 > A6D-4100 DIL SCHALTER OBEN 4POL 12.2MM PDF资料下载
参数资料
| 型号： | A6D-4100 |
| 英文描述： | DIL SCHALTER OBEN 4POL 12.2MM |
| 中文描述： | 迪勒SCHALTER奥本4POL 12.2MM |
| 文件页数： | 3/3页 |
| 文件大小： | 125K |
| 代理商： | A6D-4100 |
A6D
A6D
3
Precautions
The terminal pitch of all OMRON DIP switches is the same as a digi-
tal IC chip, which has a 2.54mm pitch. Moreover, Models A6C and
A6D DIP switches are also identical to an DIL-IC chip in shape, so
that they can be mounted on a PC board in exactly the same manner
as ordinary IC chips.
When using these OMRON DIP switches, pay attention to the fol-
lowing points:
Circuit Design
Design the circuit for the DIP switch so that the switch can be used
within the rated voltage and current ranges. The rated maximum
voltage and current must not be exceeded (even momentarily)
when the switch breaks or makes contact. The rated minimum cur-
rent is 10
μ
A (at 3.5 VDC). When CMOS iCs are used on the same
PC board as the DIP switch, the momentary current applied to the
DIP switch can be increased to improve the contact reliability on
some occasions. At this time, however, the peak value of the current
must not exceed the rated maximum value.
Mounting
The rotor is set to position 0 at the factory. Do not move the rotor to
any other position, until after the switch has been mounted on a PC
board, soldered, cleaned and dried.
1.Automatic mounting
The top actuated types of models A6C and A6D are in the same
shape as DIL-IC packages. Therefore, an automatic IC chip
mounter can be used to mount these DIP switches without modifica-
tion or, at worst, by slightly modifying the stopper. (A body stopper is
recommended as the stopper for the shoot. Do not use a half-lead
stopper. However, this depends on the automatic chip mounter to be
used. Check the specifications of the chip mounter in advance.)
Use a PC board 1.2 to 1.6mm thick.
The mounting holes on the PC board should be 0.9mm or larger in
diameter.
2.Manual mounting or use of IC socket
Use a commercially available IC chip inserting tool.
IC sockets (such as OMRON model XR) can be used to mount the
DIP switch on a PC board as the terminal size and pitch of the switch
are the same as ordinary IC chips.
When manually inserting the DIP switch terminal into the mounting
holes on a PC board, position the Dip switch so that the terminals
can be inserted into the respective mounting holes on the PC board
(or on an IC socket) all at once. Then push down the switch as far as
it will go. Apply the force at right angles to the PC board. When
removing the DIP switch from the PC board or IC socket, do not twist
the tip of a screwdriver or similar object inserted between the switch
and the PC board or IC socket. Convenient pullout tools are com-
mercially available.
Soldering
Before soldering, confirm that all the terminals of the DIP switch
have been deeply inserted into the mounting holes on the PC board.
Dip the PC board on which the DIP switch(es) are mounted in the
solder flux. The flux must not come over the surface of the PC board.
A6CV, A6DR
A6C, A6D
PC board
Flux
Both hand and automatic soldering are possible, under the following
conditions:
Max. solder
temperature
350 C
260 C
Max. solder time
Hand soldering
Automatic
soldering
3 seconds
5 seconds
Cleaning
Use freon TES to remove the solder flux. Dip the switch in an ultra-
sonic oven, a solution oven and a vapophase oven to a depth of
5cm, for 60 seconds each.
Ethyl acohol or isopropyl alcohol can also be used. If used, however,
finish the cleaning process within 5 minutes.
Do not use cleaning solvents other than these, as the switch materi-
als may degrade.
Operation
1
Use the tip of a standard screwdriver or similar object to oper-
ate the rotary DIP switch.
Use an appropriately sized screwdriver. If the tip is too large or
small, the groove of the actuator may be damaged or
deformed.
2.
The actuators of a slide type DIP switch can be moved by a
stick or ball-point pen having a round tip. Do not use sharp
edged objects such as tweezers.
3.
The top actuated types and side actuated types of the slide
DIP switches can also be operated with the fingers.
相关PDF资料 |
PDF描述 |
|---|---|
| A6D6100 | DIL SCHALTER OBEN 6POL 17.3MM |
| A6D8100 | DIL SCHALTER OBEN 8POL 22.4MM |
| A6DR-0100 | DIL SCHALTER PIANO 10POL 27.4MM |
| A6DR-4100 | DIL SCHALTER PIANO 4POL 12.2MM |
| A6DR-6100 | DIL SCHALTER PIANO 6POL 17.3MM |
相关代理商/技术参数 |
参数描述 |
|---|---|
| A6D4100 | 制造商:Omron Electronic Components LLC 功能描述:SWITCH DIL 4 WAY |
| A6D4101 | 制造商:Omron Electronic Components LLC 功能描述:Switch DIP OFF ON SPST 4 Flush Slide 0.1A 30VDC PC Pins 5000Cycle 2.54mm Thru-Hole |
| A6D4103 | 制造商:Omron Electronic Components LLC 功能描述:SWIT DIP ON OFF 4P 4 RAISED SLIDE 0.1A 30VDC PC PINS 5000CYC - Bulk 制造商:Omron Electronic Components LLC 功能描述:SWITCH DIP 4POS EXTEND ACT SLD 制造商:Omron Electronic Components LLC 功能描述:SWITCH DIP RAISED ACTUATOR 4 WAY 制造商:Omron Electronic Components LLC 功能描述:SWITCH, DIP, RAISED ACTUATOR, 4 WAY 制造商:Omron Electronic Components LLC 功能描述:Switch DIP 4 way Raised Slide Thru-Hole 制造商:Omron Electronic Components LLC 功能描述:Switch DIP ON OFF SPST 4 Raised Slide 0.1A 30VDC PC Pins 5000Cycle 2.54mm Thru-Hole Tube |
| A6D-4103 | 功能描述:DIP 开关/ SIP 开关 4 PIN SEALED RSD ACT RoHS:否 制造商:Omron Electronics 位置数量:10 开关类型:DIP 执行器:Rotary 端子节距:2.54 mm 触点形式: 端接类型:Solder Pin 电流额定值:100 mA 电压额定值 DC: 工作温度范围: 安装:Through Hole |
| A6D43DS29C2 | 功能描述:CONN CARDEDGE 43DL POS .156 GOLD 制造商:te connectivity amp connectors 系列:- 包装:散装 零件状态:有效 卡类型:非指定 - 双边 公母:母头 位/盘/排数:- 针脚数:86 卡厚度:0.054" ~ 0.071"（1.37mm ~ 1.80mm） 排数:2 间距:0.156"（3.96mm） 特性:- 安装类型:通孔 端接:焊接 触头材料:铜合金 触头镀层:金 触头镀层厚度:30μin（0.76μm） 触头类型:- 颜色:黑 法兰特性:- 工作温度:-55°C ~ 125°C 材料 - 绝缘:热塑性塑料 - 玻璃纤维 读数:双 标准包装:1,000 |
发布紧急采购，3分钟左右您将得到回复。